Low IQ, 2.25MHz, Triple Output, Buck/Buck/Boost Synchronous Controller Features: Dual Buck Plus Single Boost Synchronous Controllers Wide Bias Input Voltage Range: 4.5V to 38V Outputs Remain in Regulation Through Cold Crank Down to a 2.5V Input Supply Voltage Buck Output Voltage Range: 0.8V ≤ VOUT ≤ 24V Boost Output Voltage Up to 60V Low Operating IQ: 28μA (One Channel On) RSENSE or DCR Current Sensing 100% Duty Cycle for Boost Synchronous MOSFET Even in Burst Mode® Operation Phase-Lockable Frequency (320kHz to 2.25MHz) Programmable Fixed Frequency (320kHz to 2.25MHz) Very Low Buck Dropout Operation: 98% Duty Cycle Small 38-Lead 5mm × 7mm QFN Package

High Speed Rail-to-Rail Input Comparator with LVDS Compatible Outputs Features: Low Propagation Delay: 1.8ns Typ. Low Overdrive Dispersion: 1ns Typ. (10mV to 125mV Overdrive) High Toggle Rate: 890Mbps Typ. LVDS Compatible Output Stage Rail-to-Rail Inputs Extend Beyond Both Rails Low Quiescent Current: 13.4mA Supply Range: 2.4V to 5.25V Features within the LTC6754 Family: Separate Input and Output Supplies Shutdown Pin for Reduced Power Output Latch and Adjustable Hysteresis SC70 and 3mm × 3mm QFN Packages

100mA Wireless Li-Ion Charger with Low Battery Disconnect Features: Complete Wireless Power Receiver, Li-Ion Charger and PowerPath™ Controller Wireless Input Power Control and Rectification Wideband Wireless Power Frequency: DC to >10MHz Pin-Selectable Charge Current: 10mA/25mA/50mA/100mA Pin-Selectable Charge Voltage: 4.0V/4.1V/4.2V/4.35V Pin-Selectable Low Battery Disconnect: 2.7V/3.2V Zero Battery Drain Current in Disconnect/Ship Mode Pin-Selectable Low Battery Pre-Charge Current Enable NTC Input for Temperature Qualified Charging Safety Charge Termination Timer Tiny Total Solution Size with Few Externals Small Thermally Enhanced 12-lead 2mm × 2mm LQFN Package

100mA Wireless Li-Ion Charger with Low Battery Disconnect Features: Complete Wireless Power Receiver, Li-Ion Charger and PowerPath™ Controller Wireless Input Power Control and Rectification Wideband Wireless Power Frequency: DC to >10MHz Pin-Selectable Charge Current: 10mA/25mA/50mA/100mA Pin-Selectable Charge Voltage: 4.0V/4.1V/4.2V/4.35V Pin-Selectable Low Battery Disconnect: 2.7V/3.2V Zero Battery Drain Current in Disconnect/Ship Mode Pin-Selectable Low Battery Pre-Charge Current Enable NTC Input for Temperature Qualified Charging Safety Charge Termination Timer Tiny Total Solution Size with Few Externals Small Thermally Enhanced 12-lead 2mm × 2mm LQFN Package

Dual 1.4A, Single 2.8A Step-Down Silent Switcher Module Regulator Features: Two Complete Step-Down Switching Power Supplies Low Noise Silent Switcher® Architecture CISPR25 Class 5 Compliant Wide Input Voltage Range: 3V to 40V Wide Output Voltage Range: 0.8V to 10V 1.4A Continuous Output Current per Channel at 24VIN, 3.3VOUT, TA = 85°C Multiphase Parallel Operation to Increase Current Selectable Switching Frequency: 300kHz to 3MHz Compact Package (6.25mm × 6.25mm × 2.22mm) Surface Mount BGA

Quad DC/DC Module Regulator with Configurable 1.2A Output Array Features: Quad Output Step-Down µModule Regulator with 1.2A per Output Channel Wide Input Voltage Range: 2.7V to 17V 0.6V to 5.5V Output Voltage 1.2A DC, Parallelable, Output Current Each Channel ±1.5% Total Output Voltage Regulation 100% Duty Cycle Operation Current Mode Control, Fast Transient Response External Frequency Synchronization Selectable Burst Mode® Operation Power Good Indicator Over Voltage, Current and Temperature Protection 6.25mm × 6.25mm × 2.1mm BGA Package Pin Compatible with LTM4668 (0.6V to 1.8V Output, 1MHz)

Single Channel Transimpedance Amplifier with Output Multiplexing Features: 220MHz –3dB Bandwidth with 2pF Input Capacitance Single-Ended Output 74kΩ Transimpedance Gain 4.8pA/√Hz Input Current Noise Density at 200MHz (2pF) 64nARMS Integrated Input Current Noise Over 200MHz (2pF) Linear Input Range 0µA to 30µA Overload Current > ±400mA Peak Fast Overload Recovery: 1mA in 10ns Fast Output MUXing: <50ns Single 5V Supply 90mW Power Dissipation 2VP-P Output Swing on 100Ω Load 3mm × 3mm, 16-Lead QFN Package Output MUX Combines Multiple LTC6560 Devices AEC-Q100 Qualified for Automotive Applications

Quad Output Module Regulator with Digital Power System Management Features: Quad Outputs, Dual 12A and Dual 5A, Step-Down μModule® Regulator with Digital Interface Wide Input Voltage Range: 4.5V to 15V Dual 12A DC Output From 0.6V to 3.3V Dual 5A DC Output From 0.6V to 5.5V ±0.5% Total Output Voltage Regulation with Servo ±5% Current Readback Accuracy in 12A Channels 400kHz PMBus-Compliant I2C Serial Interface Integrated 16-Bit ΔΣ ADC Accurate Monitoring Input and Four Output Voltages, Currents, and Temperatures Digital Programmable Output Voltage Trim, Sequencing and Margining for Each Channel Manage Faults and Warnings Onboard EEPROM Fault Log Record Dual True Differential Sensing Amplifier Parallelable Output for Higher Output Current Drop-In Pin Compatible with Quad Output LTM4671 Non-PSM μModule Regulator 16mm × 16mm × 4.72mm BGA Package

25A Monolithic Synchronous DC/DC Step-Down Converter with PMBus Interface Features: 4.5V to 20V VIN Range 1% Total VOUT Accuracy Over Temperature Single Resistor-Programmable Reference Voltage: 0.4V to 3.5V PMBus Compliant Serial Interface: Programmable Output Voltage Margining: Up to ±25% VOUT Range with 0.1% Resolution Read Back of Average and Peak Temperature, Current, and Voltage (25Hz Refresh Rate) Fault Status Phase-Lockable Fixed Frequency Up to 2MHz Less Than 1ms Power-Up Time Optional External Reference Input Pin Selectable Fast-Margining of the Output Voltage Power Good Flag with Pin Programmable Thresholds and Filter Delay Differential Remote Output Voltage Sensing Master Shutdown Mode: 125μA Supply Current Clock Out for 2-Phase Operation (50A Load) Available in a Thermally-Enhanced 6.25mm × 7.5mm × 2.22mm BGA Package

65A+ Power/Energy Monitor with Integrated Sense Resistor Features: Measures Current, Voltage, Power, Charge, Energy ±65A Current Range with Low 18mA Offset Integrated 150µΩ Sense Resistor 0V to 15V Input Range Independent of Supply Voltage Instantaneous Multiplication of Voltage and Current 0.5% Voltage Accuracy 1% Current and Charge Accuracy 1.2% Power and Energy Accuracy Alerts When Thresholds Exceeded Stores Maximum and Minimum Values Shutdown Mode with IQ < 10µA I2C/SPI Compatible Interface Available in 38-Lead 5mm × 7mm QFN Package

7.5kVRMS SPI/Digital or I2C Module Isolator with Transformer Driver Features: 6-Channel Logic Isolator: 7500VRMS for 1 Minute 16.2mm Creepage CSA (IEC/UL) Approved, File #255632 3V to 5.5V Supply Operation Transformer Driver with Integrated Isolated Side LDO SPI/Digital (LTM2810-S) or I2C (LTM2810-I) Options High Common Mode Transient Immunity: 50kV/μs High Speed Operation: 10MHz Digital Isolation 4MHz/8MHz SPI Isolation 400kHz I2C Isolation Operation Up to 125°C (H-Grade) 1.62V to 5.5V Logic Supplies for Flexible Digital Interfacing ±25kV ESD HBM Across the Isolation Barrier Maximum Continuous Working Voltage: 1kVRMS, 1.6kVDC Low Current Shutdown Mode (<10µA) 22mm × 6.25mm × 2.06mm BGA Package

Low IQ Boost/SEPIC/Inverting Converter with 1.5A, 150V Switch Features: Wide Input Voltage Range: 2.8V to 60V Ultralow Quiescent Current and Low Ripple Burst Mode® Operation: IQ = 9µA 1.5A, 150V Power Switch Positive or Negative Output Voltage Programming with a Single Feedback Pin Programmable Frequency (100kHz to 500kHz) Synchronizable to an External Clock Spread Spectrum Frequency Modulation for Low EMI BIAS Pin for Higher Efficiency Programmable Undervoltage Lockout (UVLO) Thermally Enhanced 16-lead MSOP Package AEC-Q100 Qualified for Automotive Applications

20V, 200mA, Ultralow Noise, Ultrahigh PSRR RF Linear Regulator Features: Ultralow RMS Noise: 0.8μVRMS (10Hz to 100kHz) Ultralow Spot Noise: 2nV/√Hz at 10kHz Ultrahigh PSRR: 79dB at 1MHz Output Current: 200mA Wide Input Voltage Range: 1.8V to 20V Single Capacitor Improves Noise and PSRR 100μA SET Pin Current: ±1% Initial Accuracy Single Resistor Programs Output Voltage High Bandwidth: 1MHz Programmable Current Limit Low Dropout Voltage: 350mV Output Voltage Range: 0V to 15V Programmable Power Good Fast Start-Up Capability Precision Enable/UVLO Parallelable for Lower Noise and Higher Current Internal Current Limit with Foldback Minimum Output Capacitor: 4.7μF Ceramic Reverse Battery and Reverse Current Protection 10-Lead MSOP and 3mm × 3mm DFN Packages AEC-Q100 Qualified for Automotive Applications

300mA Low Voltage Buck-Boost Converter with PowerPath and 1.6A Quiescent Current Features:Dual Input Buck-Boost with Integrated PowerPath™ ManagerUltralow Start-Up Voltages: 850mV Start with No Backup Source, 300mV with a Backup SourceCompatible with Primary or Rechargeable Backup BatteriesDigitally Selectable VOUT and VSTOREMaximum Power Point ControlUltralow Quiescent Current: 1.6μARegulated Output with VIN or VSTORE Above, Below or Equal to the OutputOptional Backup Battery Trickle ChargerShelf Mode Disconnect Function to Preserve Battery Shelf LifeBurst Mode® OperationAccurate RUN Pin ThresholdPower Good Output Voltage IndicatorSelectable Peak Current Limit: 90mA/650mAAvailable in Thermally Enhanced 3mm × 4mm 16-Pin QFN and 20-Pin TSSOP Packages

Dual 13A or Single 26A DC/DC Module (Power Module) Regulator Features: Dual 13A or Single 26A Output Wide Input Voltage Range: 4.5V to 16V Output Voltage Range: 0.6V to 5.3V ±1.5% Maximum Total DC Output Error Multiphase Current Sharing with Multiple LTM4620As Up to 100A Higher Efficiency and Wider VOUT Range Than LTM4620 Differential Remote Sense Amplifier Current Mode Control/Fast Transient Response Adjustable Switching Frequency Overcurrent Foldback Protection Frequency Synchronization Internal Temperature Monitor Output Overvoltage Protection Pin Compatible with the LTM4628 (Dual 8A) and LTM4620 (Dual 13A) Thermally Enhanced (15mm × 15mm × 4.41mm) LGA Package and (15mm × 15mm × 5.01mm) BGA Package

Dual 18A or Single 36A DC/DC Module Regulator Features: Dual 18A or Single 36A Output Input Voltage Range: 4.5V to 18V (after date code 1720*) Output Voltage Range: 0.6V to 8V (after date code 1720*) ±1.5% Maximum Total DC Output Error Over Line, Load and Temperature Higher Light Load Efficiency and Wider VOUT Range Than LTM4630 Differential Remote Sense Amplifier Current Mode Control/Fast Transient Response Multiphase Parallel Current Sharing Up to 144A Internal Temperature Monitor Pin Compatible with the LTM4620A (Dual 13A, Single 26A) and LTM4630 (Dual 18A, Single 36A) Adjustable Switching Frequency or Synchronization Overcurrent Foldback Protection Selectable Burst Mode® Operation, Pulse Skipping Mode Operation Soft-Start/Voltage Tracking Output Overvoltage Protection 16mm × 16mm × 4.41mm LGA and 16mm × 16mm × 5.01mm BGA Packages

Ultrathin Dual 10A or Single 20A DC/DC Module Regulator Features:Dual 10A or Single 20A OutputInput Voltage Range: 4.5V to 15VOutput Voltage Range: 0.6V to 1.8V±1.5% Maximum Total DC Output Error Over Line, Load and TemperatureDifferential Remote Sense AmplifierCurrent Mode Control/Fast Transient ResponseAdjustable Switching FrequencyOvercurrent Foldback ProtectionMultiphase Parallel Current Sharing with Multiple LTM4631sFrequency SynchronizationInternal Temperature MonitorSelectable Burst Mode® OperationSoft-Start/Voltage TrackingOutput Overvoltage ProtectionUltrathin 16mm × 16mm × 1.91mm LGA and 16mm x 16mm x 2.51mm BGA Packages

SmartMesh IP Wireless 802.15.4e System-on-Chip Features: 72-pin 10mm × 10mm QFN package 2.4 GHz, IEEE 802.15.4e System-on-Chip, Complete with Embedded SmartMesh Networking Software >99.999% Network Reliability in the Most Challenging RF Environments Sub 50µA Routing Nodes Serves as either a Wireless Mote, EManager, or Access Point Mote in a SmartMesh IP network These products contain encryption. Import/export restrictions may apply.

Hot Swap Controller with I2C Compatible Monitoring Features: Allows Safe Board Insertion Into Live Backplane 12-/16-Bit ADC with ±0.7% Total Unadjusted Error Monitors Current, Voltage, Power and Energy Internal EEPROM for Nonvolatile Configuration Wide Operating Voltage Range: 2.9V to 33V I2C/SMBus Digital Interface (Coexists with PMBus Devices) 12V Gate Drive for Lower MOSFET RDS(ON) Programmable Current Limit with 2% Accuracy MOSFET Power Limiting with Current Foldback Continuously Monitors MOSFET Health Stores Minimum and Maximum Measurements Alerts When Alarm Thresholds Exceeded Reboots on I2C Command Input Overvoltage and Undervoltage Protection Three General Purpose Input/Outputs Internal ±5% or External Timebases 28-Pin 4mm × 5mm QFN Package AEC-Q100 Qualified for Automotive Applications

24-Bit, 1.5Msps/2Msps, Low Power SAR ADC with Integrated Digital Filter Features:Guaranteed 24-Bits No Missing Codes±0.5ppm INL (Typ)Integrated Digital Filter with Real-Time AveragingLow Power: 28mW at 2Msps100dB SNR (Typ) at 1.5Msps145dB Dynamic Range (Typ) at 30.5sps–117dB THD (Typ) at fIN = 2kHz50Hz/60Hz RejectionDigital Gain Compression (DGC)Guaranteed Operation to 85°CSingle 2.5V SupplyFully Differential Input Range Up to ±5V1.8V to 5V SPI-Compatible Serial I/O with Daisy- Chain Mode16-Lead MSOP and 4mm × 3mm DFN Packages