The AD7745/AD7746 are a high resolution, ?-? capacitance-to-digital converter (CDC). The capacitance to be measured is connected directly to the device inputs. The architecture fea-tures inherent high resolution (24-bit no missing codes, up to 21-bit effective resolution), high linearity (?0.01%), and high accuracy (?4 fF factory calibrated). The AD7745/AD7746 capacitance input range is ?4 pF (changing), while it can accept up to 17 pF common-mode capacitance (not changing), which can be balanced by a programmable on-chip, digital-to-capacitance converter (CAPDAC). The AD7745 has one capacitance input channel, while the AD7746 has two channels. Each channel can be configured as single-ended or differential. The AD7745/AD7746 are designed for floating capacitive sensors. For capacitive sensors with one plate connected to ground, the AD7747 is recommended. The parts have an on-chip temperature sensor with a resolution of 0.1?C and accuracy of ?2?C. The on-chip voltage reference and the on-chip clock generator eliminate the need for any external components in capacitive sensor applications. The parts have a standard voltage input, which together with the differential reference input allows easy interface to an external temperature sensor, such as an RTD, thermistor, or diode. The AD7745/AD7746 have a 2-wire, I2C-compatible serial interface. Both parts can operate with a single power supply from 2.7 V to 5.25 V. They are specified over the automotive temperature range of ?40?C to +125?C and are housed in a 16-lead TSSOP package. ApplicationsAutomotive, Industrial and Medical Systems for: Pressure Measurement Position Sensors Level Sensors Flowmeters Humidity Sensors Impurity Detection

The AD7745/AD7746 are a high resolution, ?-? capacitance-to-digital converter (CDC). The capacitance to be measured is connected directly to the device inputs. The architecture fea-tures inherent high resolution (24-bit no missing codes, up to 21-bit effective resolution), high linearity (?0.01%), and high accuracy (?4 fF factory calibrated). The AD7745/AD7746 capacitance input range is ?4 pF (changing), while it can accept up to 17 pF common-mode capacitance (not changing), which can be balanced by a programmable on-chip, digital-to-capacitance converter (CAPDAC). The AD7745 has one capacitance input channel, while the AD7746 has two channels. Each channel can be configured as single-ended or differential. The AD7745/AD7746 are designed for floating capacitive sensors. For capacitive sensors with one plate connected to ground, the AD7747 is recommended. The parts have an on-chip temperature sensor with a resolution of 0.1?C and accuracy of ?2?C. The on-chip voltage reference and the on-chip clock generator eliminate the need for any external components in capacitive sensor applications. The parts have a standard voltage input, which together with the differential reference input allows easy interface to an external temperature sensor, such as an RTD, thermistor, or diode. The AD7745/AD7746 have a 2-wire, I2C-compatible serial interface. Both parts can operate with a single power supply from 2.7 V to 5.25 V. They are specified over the automotive temperature range of ?40?C to +125?C and are housed in a 16-lead TSSOP package. ApplicationsAutomotive, Industrial and Medical Systems for: Pressure Measurement Position Sensors Level Sensors Flowmeters Humidity Sensors Impurity Detection

The AD7796/AD7797 are complete, analog front ends for highprecision, bridge sensor applications such as weigh scales. TheAD7796/AD7797 contain a ?-? ADC capable of 16-/24-bitresolution, respectively. The on-chip instrumentation amplifierhas a fixed gain of 128, allowing small amplitude signals such asthose from bridge sensors to be directly interfaced to the ADC.Each device has one differential input and contains a temperaturesensor that is internally connected to the ADC. This sensor canbe used to perform temperature compensation of the bridge.The devices can be operated with the internal clock or an externalclock. The output data rate from the devices is software-programmableand can be varied from 4.17 Hz to 123 Hz.The AD7796/AD7797 operate with a power supply from 2.7 Vto 5.25 V. Each device consumes a current of 250 ?A typical andis housed in a 16-lead TSSOP.Applications Weigh scales Strain gages Industrial process control Instrumentation Portable instrumentation

The AD7843 is a 12-bit successive-approximation ADC with a synchronous serial interface and low on resistance switches for driving touch screens. The part operates from a single 2.2 V to 5.25 V power supply and features throughput rates greater than 125 kSPS. The external reference applied to the AD7843 can be varied from 1 V to +VCC, while the analog input range is from 0 V to VREF. The device includes a shutdown mode that reduces the current consumption to less than 1 ?A. This part is available in a 16-lead 0.15' Quarter Size Outline (QSOP) package and a 16-lead Thin Shrink Small Outline (TSSOP) package.?Also see the AD7843 sister part, which is the AD7873. This part is similar to the AD7843 but has added functionality such as an on-chip temperature sensor (-40?C to + 85?C), on-chip 2.5 V reference and direct battery and touch-pressure measurement.

The AD7879/AD7889 are 12-bit successive approximationanalog-to-digital converters (SAR ADCs) with a synchronousserial interface and low on-resistance switches for driving 4-wireresistive touch screens. The AD7879/AD7889 work with a verylow power supply?a single 1.6 V to 3.6 V supply?and feature athroughput rate of 105 kSPS. The devices include a shutdownmode that reduces current consumption to less than 6 ?A.To reduce the effects of noise from LCDs and other sources, theAD7879/AD7889 contain a preprocessing block. Thepreprocessing function consists of a median filter and anaveraging filter. The combination of these two filters provides amore robust solution, discarding the spurious noise in the signaland keeping only the data of interest. The size of both filters isprogrammable. Other user-programmable conversion controlsinclude variable acquisition time and first conversion delay; upto 16 averages can be taken per conversion. The AD7879/AD7889can run in slave mode or standalone (master) mode, using anautomatic conversion sequencer and timer.The AD7879/AD7889 have a programmable pin that canoperate as an auxiliary input to the ADCs, as a battery monitor,or as a general-purpose input/output (GPIO). In addition, aprogrammable interrupt output can operate in three modes: as ageneral-purpose interrupt to signal when new data is available(DAV), as an interrupt to indicate when limits are exceeded(INT), or as a pen-down interrupt when the screen is touched(PENIRQ). The AD7879/AD7889 offer temperaturemeasurement and touch pressure measurement.The AD7879 is available in a 12-ball, 1.6 mm ? 2 mm WLCSPand in a 16-lead, 4 mm ? 4 mm LFCSP. The AD7889 is availablein a backside coated version of the WLCSP. Both devices supportan SPI interface (AD7879/AD7889) or an I2C interface (AD7879-1/AD7889-1).Applications Personal digital assistants Smart handheld devices Touch screen monitors Point-of-sale terminals Medical devices Cell phones

The AD7879/AD7889 are 12-bit successive approximationanalog-to-digital converters (SAR ADCs) with a synchronousserial interface and low on-resistance switches for driving 4-wireresistive touch screens. The AD7879/AD7889 work with a verylow power supply?a single 1.6 V to 3.6 V supply?and feature athroughput rate of 105 kSPS. The devices include a shutdownmode that reduces current consumption to less than 6 ?A.To reduce the effects of noise from LCDs and other sources, theAD7879/AD7889 contain a preprocessing block. Thepreprocessing function consists of a median filter and anaveraging filter. The combination of these two filters provides amore robust solution, discarding the spurious noise in the signaland keeping only the data of interest. The size of both filters isprogrammable. Other user-programmable conversion controlsinclude variable acquisition time and first conversion delay; upto 16 averages can be taken per conversion. The AD7879/AD7889can run in slave mode or standalone (master) mode, using anautomatic conversion sequencer and timer.The AD7879/AD7889 have a programmable pin that canoperate as an auxiliary input to the ADCs, as a battery monitor,or as a general-purpose input/output (GPIO). In addition, aprogrammable interrupt output can operate in three modes: as ageneral-purpose interrupt to signal when new data is available(DAV), as an interrupt to indicate when limits are exceeded(INT), or as a pen-down interrupt when the screen is touched(PENIRQ). The AD7879/AD7889 offer temperaturemeasurement and touch pressure measurement.The AD7879 is available in a 12-ball, 1.6 mm ? 2 mm WLCSPand in a 16-lead, 4 mm ? 4 mm LFCSP. The AD7889 is availablein a backside coated version of the WLCSP. Both devices supportan SPI interface (AD7879/AD7889) or an I2C interface (AD7879-1/AD7889-1).Applications Personal digital assistants Smart handheld devices Touch screen monitors Point-of-sale terminals Medical devices Cell phones

The AD7902 is a dual 16-bit, successive approximation, analog-to-digital converter (ADC) that operates from a single power supply, VDDx, per ADC. It contains two low power, high speed, 16-bit sampling ADCs and a versatile serial port interface (SPI). On the CNVx rising edge, the AD7902 samples an analog input, ?IN+ in the range of 0 V to VREF with respect to a ground sense, IN?. The externally applied reference voltage of the REFx pins (VREF) can be set independently from the supply voltage pins, VDDx. The power of the device scales linearly with throughput.Using the SDIx inputs, the SPI-compatible serial interface can also daisy-chain multiple ADCs on a single 3-wire bus and provide an optional busy indicator. It is compatible with 1.8 V, 2.5 V, 3 V, or 5 V logic, using the separate VIOx supplies.The AD7902 is available in a 20-lead QSOP package with operation specified from ?40?C to +125?C.APPLICATIONS Battery-powered equipment Communications Automated test equipment (ATE) Data acquisition Medical instrumentation Redundant measurement Simultaneous sampling

The AD7915/AD7916 are 16-bit, successive approximation, analog-to-digital converters (ADCs) that operate from a single power supply, VDD. They contain a low power, high speed, 16-bit sampling ADC and a versatile serial interface port. On the CNV rising edge, the AD7915/AD7916 sample the voltage difference between the IN+ and IN? pins. The voltages on these pins typically swing in opposite phases between 0 V and VREF. The reference voltage, REF, is applied externally and can be set independent of the supply voltage, VDD. The power consumption of the AD7915/AD7916 scales linearly with throughput.The AD7915/AD7916 are serial peripheral interface (SPI) compatible, which features the ability, using the SDI input, to daisy-chain several ADCs on a single 3-wire bus. They are compatible with 1.8 V, 2.5 V, 3 V, and 5 V logic using the separate VIO supply.The AD7915/AD7916 are available in a 10-lead MSOP or a 10-lead LFCSP with operation specified from ?40?C to +125?C.APPLICATIONS Automated test equipment Data acquisition systems Medical instruments Machine automation

The AD9837 is a low power, programmable waveform generatorcapable of producing sine, triangular, and square wave outputs.Waveform generation is required in various types of sensing,actuation, and time domain reflectometry (TDR) applications. The outputfrequency and phase are software programmable, allowing easytuning. The frequency registers are 28 bits: with a 16 MHz clock rate, resolution of 0.06 Hz can be achieved; with a 5 MHz clock rate, the AD9837can be tuned to 0.02 Hz resolution.The AD9837 is written to via a 3-wire serial interface. This serialinterface operates at clock rates up to 40 MHz and is compatiblewith DSP and microcontroller standards. The device operateswith a power supply from 2.3 V to 5.5 V.The AD9837 has a power-down (SLEEP) function. Sections of the device that are not being used can be powered down to minimize the current consumption of the part. For example, the DAC can be powered down when a clock output is being generated.The AD9837 is available in a 10-lead LFCSP_WD package.APPLICATIONS Frequency stimulus/waveform generation Liquid and gas flow measurement Sensory applications: proximity, motion, and defect detection Line loss/attenuation Test and medical equipment Sweep/clock generators Time domain reflectometry (TDR) applications

NEWER ALTERNATIVES: AD5764R Quad, 16-Bit, 1LSB INL, Bipolar Voltage Output DAC with Internal Reference AD5754R Complete, Quad, 16-Bit, Unipolar/Bipolar Voltage Output DAC with Internal Reference AD5754 Complete, Quad, 16-Bit, Unipolar/Bipolar Voltage Output DACThe AD5764 is a quad, 16-bit, serial input, bipolar voltage output DAC that operates from supply voltages of ?11.4 V to ?16.5 V. Nominal full-scale output range is ?10 V. The AD5764 provides integrated output amplifiers, reference buffers, and proprietary power-up/power-down control circuitry. The part also features a digital I/O port that is programmed via the serial interface. The part incorporates digital offset and gain adjust registers per channel.The AD5764 is a high performance converter that offers guaranteed monotonicity, integral nonlinearity (INL) of ?1 LSB, low noise, and 10 ?s settling time. During power-up (when the supply voltages are changing), VOUTx is clamped to 0 V via a low impedance path.The AD5764 uses a serial interface that operates at clock rates of up to 30 MHz and is compatible with DSP and microcontroller interface standards. Double buffering allows the simultaneous updating of all DACs. The input coding is programmable to either twos complement or offset binary formats. The asynchronous clear function clears the data register to either bipolar zero or zero scale depending on the coding used. The AD5764 is ideal for both closed-loop servo control and open-loop control applications. The AD5764 is available in a 32-lead TQFP, and offers guaranteed specifications over the ?40?C to +85?C industrial temperature range. See Figure 1 for the functional block diagram.APPLICATIONS Industrial automation Open-loop/closed-loop servo control Process control Data acquisition systems Automatic test equipment Automotive test and measurement High accuracy instrumentation

The AD5755-1 is a quad, voltage and current output digital-to-analog converter (DAC) that operates with a power supply range from ?26.4 V to +33 V. On-chip dynamic power control minimizes package power dissipation in current mode. This is achieved by regulating the voltage on the output driver from 7.4 V to 29.5 V using a dc-to-dc boost converter optimized for minimum on-chip power dissipation. Each channel has a corresponding CHART pin so that HART signals can be coupled onto the current output of the AD5755-1.The device uses a versatile 3-wire serial interface that operates at clock rates of up to 30 MHz and is compatible with standard SPI, QSPI?, MICROWIRE?, DSP, and microcontroller interface standards. The interface also features optional CRC-8 packet error checking, as well as a watchdog timer that monitors activity on the interface.PRODUCT HIGHLIGHTS Dynamic power control for thermal management. 16-bit performance. Multichannel. HART compliant.?APPLICATIONS Process control Actuator control Programmable logic controllers (PLCs) HART network connectivity

Data Conversion IC Development Tools EVALUATION CONTROL BOARD I.C.

The AD7734 is a high precision, high throughput analog front end. True 16-bit p-p resolution is achievable with a total conversion time of 500 ?s (2 kHz channel switching), making it ideally suitable for high resolution multiplexing applications.The device can be configured via a simple digital interface, which allows users to balance the noise performance against data throughput up to a 15.4 kHz.The analog front end features four single-ended input channels with unipolar or true bipolar input ranges to ?10 V while operating from a single +5 V analog supply. The device has an overrange and underrange detection capability and accepts an analog input overvoltage to ?16.5 V without degrading the performance of the adjacent channels.The differential reference input features ?No-Reference? detect capability. The ADC also supports per channel system calibration options. The digital serial interface can be configured for 3-wire operation and is compatible with microcontrollers and digital signal processors. All interface inputs are Schmitt triggered.The device is specified for operation over the extended industrial temperature range of ?40?C to +105?C.Other devices in the AD7734 family are the AD7732?and the AD7738.The AD7732 is similar to AD7734, but its analog front end features two fully differential input channels.The AD7738 analog front end is configurable for four fully differential or eight single-ended input channels, features 0.625 V to 2.5 V bipolar/unipolar input ranges, and accepts a common-mode input voltage from 200 mV to AVDD?300 mV. The AD7738 multiplexer output is pinned out externally, allowing the user to implement programmable gain or signal conditioning before being applied to the ADC.APPLICATIONS PLCs/DCS Multiplexing applications Process control Industrial instrumentation

The ADCMP604?/ ADCMP605 are very fast comparators fabricated on the Analog Devices, Inc. proprietary XFCB2 process. These comparators are exceptionally versatile and easy to use. Features include an input range from VEE ? 0.5 V to VCCI + 0.2 V, low noise, LVDS-compatible output drivers, and TTL/CMOS latch inputs with adjustable hysteresis and/or shut-down inputs.The devices offer 1.5 ns propagation delays with 1 ps rms random jitter (RJ). Overdrive and slew rate dispersion are typically less than 50 ps.A flexible power supply scheme allows the devices to operate with a single 2.5 V positive supply and a ?0.5 V to +2.7 V input signal range up to a 5.5 V positive supply with a ?0.5 V to +5.7 V input signal range. Split input/output supplies, with no sequencing restrictions on the ADCMP605, support a wide input signal range with greatly reduced power consumption.The LVDS-compatible output stage is designed to drive any standard LVDS input. The comparator input stage offers robust protection against large input overdrive, and the outputs do not phase reverse when the valid input signal range is exceeded. High speed latch and programmable hysteresis features are also provided in a unique single-pin control option.The ADCMP604 is available in a 6-lead SC70 package, and the ADCMP605 is available in a 12-lead LFCSP.APPLICATIONS High speed instrumentation Clock and data signal restoration Logic level shifting or translation Pulse spectroscopy High speed line receivers Threshold detection Peak and zero-crossing detectors High speed trigger circuitry Pulse-width modulators Current-/voltage-controlled oscillators Automatic test equipment (ATE)

DC736A: Demo Board for the LT3724 High Voltage, Current Mode Switching Regulator Controller.

DC740A-A: Demo Board for the LTC2922 Power Supply Tracker with Input Monitors.

Demonstration circuit 742B features the LTC2449, an 8-/16-channel, high speed, 24-bit ΔΣ ADC with ten selectable speed/resolution modes from 6.9Hz/200nVRMS to 3.5kHz/25μVRMS (4kHz with external oscillator). Key DC specifications include 5ppm INL, 5μV offset, 10ppm fullscale error and 20nV/°C offset drift. In the 6.9Hz/200nVRMS mode, input normal mode rejection of 50Hz and 60Hz noise is better than 87dB. The accuracy (offset, full-scale, linearity, drift) and power dissipation are independent of the speed selected. The LTC2449 performs auto-zeroing of the ADC by reversing the inputs through the multiplexer output/ADC input connections. This allows an external dual buffer amplifier to isolate the signal inputs from the sampling current of the ADC.

DC751A-C: Demo Board for the LTC2232 10-Bit, 105Msps ADCs.

The LTC2704-16/LTC2704-14/LTC2704-12 are serial input, 12-, 14- or 16-bit, voltage output SoftSpan? DACs that operate from 3V to 5V logic and ?5V to ?15V analog supplies. SoftSpan offers six output spans?two unipolar and four bipolar?fully programmable through the 3-wire SPI serial interface. INL is accurate to 1LSB (2LSB for the LTC2704-16). DNL is accurate to 1LSB for all versions. Readback commands allow verification of any on-chip register in just one 24- or 32- bit instruction cycle. All other commands produce a ?rolling readback? response from the LTC2704, dramatically reducing the needed number of instruction cycles. A Sleep command allows any combination of DACs to be powered down. There is also a reset flag and an offset adjustment pin for each channel.Applications Process Control and Industrial Automation Direct Digital Waveform Generation Software Controlled Gain Adjustment Automated Test Equipment

DC766A: Demo Board for the LTC4068-4.2 Standalone Linear Li-Ion Battery Charger with Programmable Termination.