LTC4053EMSE-4.2 | Li-Ion Battery Charger, VIN = 4.25V to 6.3V, Bat = 4.2V @ 0.5A/1A
Analog Devices Inc.DC705A: Demo Board for the LTC4053-4.2 USB Compatible Lithium-Ion Battery Charger with Thermal Regulation.
TMP108EVM - Evaluate TMP108 Digital Temperature Sensor with Two-Wire Interface in WCSP
Texas InstrumentsTMP108EVM - Evaluate TMP108 Digital Temperature Sensor with Two-Wire Interface in WCSP
LTC3558EUD | Linear USB Battery Charger with Buck and Buck-Boost Regulators
Analog Devices Inc.DC1276B: Demo Board for LTC3558 - Linear USB Battery Charger with Buck and Buck-Boost Regulators
LM3414 LM3414HV 1A 65V LED Driver PSOP-8 Evaluation Board
Texas InstrumentsLM3414 LM3414HV 1A 65V LED Driver PSOP-8 Evaluation Board
controlCARD with Piccolo TMS320F28069MPZT; InstaSPIN-FOC and InstaSPIN-MOTION enabled
Texas InstrumentscontrolCARD with Piccolo TMS320F28069MPZT; InstaSPIN-FOC and InstaSPIN-MOTION enabled
C2000 Piccolo MCU F28027F LaunchPad™ development kit
Texas InstrumentsC2000 Piccolo MCU F28027F LaunchPad™ development kit
ADP8140EB-EVALZ
Analog Devices Inc.The ADP8140 provides high current control of up to four LED drivers. Each driver can sink up to 500 mA. The sink current is programmed for all four drivers with one external resistor.The device features a feedback output that controls an external power supply for optimal efficiency. The ADP8140 also protects the LEDs, power supply, and itself against thermal events, short circuits, overvoltages, and LED open circuits. Multiple ADP8140 ICs are easily connected in parallel to drive additional LED strings or higher current LEDs. The ADP8140 is available in a small, thermally enhanced, lead frame chip scale package (LFCSP).Applications High brightness LED lighting Large format LED backlighting
TUSB320LAI USB Type-C Configuration Channel Logic and Port Control Evaluation Module
Texas InstrumentsTUSB320LAI USB Type-C Configuration Channel Logic and Port Control Evaluation Module
High-Efficiency, Switch-Mode Battery Charge and Power Path Management Evaluation Module
Texas InstrumentsHigh-Efficiency, Switch-Mode Battery Charge and Power Path Management Evaluation Module
Triple op amp evaluation module for SSOP-16 (flow-through pinout) package
Texas InstrumentsTriple op amp evaluation module for SSOP-16 (flow-through pinout) package
Evaluation Module for bq27425 System-Side Impedance Track? Fuel Gauge Battery | Gas Gauge Battery
Texas InstrumentsEvaluation Module for bq27425 System-Side Impedance Track? Fuel Gauge Battery | Gas Gauge Battery
520kHz 1.6MHz - Space-Efficient Boost and SEPIC DC-DC Regulator LM2735X SEPIC 6-Pin LLP Demo Board
Texas Instruments520kHz 1.6MHz - Space-Efficient Boost and SEPIC DC-DC Regulator LM2735X SEPIC 6-Pin LLP Demo Board
OPA2810 FET-input; Voltage-feedback Operational Amplifier Evaluation Module
Texas InstrumentsOPA2810 FET-input; Voltage-feedback Operational Amplifier Evaluation Module
EVALZ-ADPD2214
Analog Devices Inc.The ADPD2214 is an optical sensor optimized for biomedical applications. Very low power consumption and near theoretical signal-to-noise ratio (SNR) are achieved by packaging an ultralow capacitance deep junction silicon photodiode operated in zero bias photoconductive mode with a low noise current amplifier. The ADPD2214 offers a typical 75 kHz bandwidth performance, which is well suited for use with pulsed excitation. The ADPD2214 uses very little power during operation and incorporates a power-down pin, enabling power cycling to optimize battery life in portable applications. The ADPD2214 provides shot noise limited performance, making it an excellent choice for measuring signals with the highest possible fidelity in low light conditions. This combination of low power, very high SNR, and electromagnetic interference (EMI) immunity enables low-power system solutions not possible with traditional photodiode (PD) and transimpedance amplifier (TIA) systems.Applications Heart rate, pulse oximetry monitoring (photoplethysmography) Battery-powered medical sensors Chemical analysis
DC1199A
Analog Devices Inc. The LT3595 is a high performance LED Driver designed to drive sixteen independent channels of up to 10 LEDs at currents up to 50mA. Series connection of the LEDs provides identical LED currents resulting in uniform brightness. Power switches, Schottky diodes, and compensation components are all internal, providing a small converter footprint and lower component cost. The high 2MHz switching frequency permits the use of tiny, low pro? le inductors and capacitors. A fixed frequency, current mode architecture results in stable operation over a wide range of supply and output voltage. A single external resistor sets the LED current for all sixteen channels, and dimming is then controlled for each channel by pulse width modulating the individual PWM pins. Relative current matching among the sixteen drivers is 8% and the PWM dimming range is 5000:1. The part is available in a 5mm x 9mm x 0.75mm 56-pin QFN package. Applications LED Video Billboards LCD Televisions Stadium and Advertising Displays
