x2 Active Multiplier SMT, 20 - 25 GHz Features: Output Power: +11 dBm Wide Input Power Range: -4 to +6 dBm Fo, 3Fo Isolation: >20 dBc @ Fout= 20 GHz 100 KHz SSB Phase Noise: -135 dBc/Hz Single Supply: +5V@ 48 mA RoHS Compliant 3×3 mm SMT Package

Medium Power Amplifier SMT, 5 - 20 GHz Features: Gain: 19 dB Saturated Power: +21 dBm @ 21% PAE Output IP3: +30 dBm Single Supply: +5V @ 114 mA 50 Ohm Matched Input/Output RoHS Compliant 3x3 mm SMT package

1 Watt Power Amplifier SMT, 0.4 - 2.2 GHz Features: Output IP3: +48 dBm 22.5 dB Gain @ 400 MHz 9 dB Gain @ 2100 MHz 53% PAE @ +31 dBm Pout +24 dBm CDMA2000 Channel Power@ -45 dBc ACP Single +5V Supply Integrated Power Control (VPD) QSOP16G SMT Package: 29.4 mm²

GaAs pHEMT MMIC Low Noise Amplifier, DC - 20 GHz Features: Noise Figure: 2.5 dB @ 10 GHz Gain: 14 dB @ 10 GHz P1dB Output Power: +16.5 dBm @ 10 GHz Supply Voltage: +8V @ 75 mA 50 Ohm Matched Input/Output 32 Lead Ceramic 5 x 5 mm SMT Package: 25 mm2

VCO SMT w/Buffer Amplifier, 6.1 - 6.72 GHz Features: Pout: +4.5 dBm Phase Noise: -101 dBc/Hz @100 KHz No External Resonator Needed Single Supply: +3V @ 31 mA QFN Leadless SMT Package, 16 mm2

1 dB LSB GaAs MMIC 3-Bit Digital Positive Control Attenuator, DC-6 GHz Features: 1 dB LSB Steps to 7 dB High IP3: +55 dBm ±0.25 dB Typical Bit Error Single Control Line Per Bit Single +5V Supply 16 Lead 3×3 mm SMT Package: 9 mm2

Dual SiGe HBT Gain Block Amplifier SMT, DC - 5 GHz Features: +20 dBm P1dB Output Power 20 dB Gain  Output IP3: +34 dBm Supply (Vs): +6V to +12V  14.9 mm² Ultra Small 8 Lead MSOP

HMC474MP86 / HMC474SC70SiGe, HBT gain block amplifiers, SMT, dc to 6 GHz Features: Gain: 15 dB or 15.5 dB P1dB output power: 8 dB Output third-order intercept points (IP3s): 20 dBm or 22 dBm Cascadable 50 inputs/outputs Single supply: 3 V to 10 V Industry standard SC70 Package

SiGe HBT Gain Block MMIC Amplifier, DC - 5 GHz Features: P1dB Output Power: +20 dBm Gain: 20 dB Output IP3: +33 dBm Cascadable 50 Ohm I/Os Single Supply: +6V to +12V Included in the HMC-DK001 Designer’s Kit

DBL-BAL Mixer SMT w/LO Amplifier, 4 - 7 GHz Features: Low Conversion Loss: 7 dB Double-Balanced Topology Integrated LO Amp: 0 to +6 dBm Drive Input IP3: +15 dBm Single Supply: +5V @ 46 mA MSOP8-G Package: 14.8 mm²

Low Noise Amplifier, 0.4 GHz to 11 GHz Features: Low noise figure: 1.4 dB typical Single positive supply (self biased) High gain: ≤15.5 dB typical High OIP3: ≤33 dBm typical RoHS-compliant, 2 mm × 2 mm, 6-lead LFCSPHMC8412TCPZ-EP Supports defense and aerospace applications (AQEC standard) Download the HMC8412TCPZ-EP data sheet (pdf) Military temperature range (−55°C to +125°C) Controlled manufacturing baseline 1 assembly/test site 1 fabrication site Product change notification Qualification data available on request V62/21602 DSCC Drawing Number

GaAS MMIC 6 Bit Digital Phase Shifters, 1.2 - 1.4 GHz Features: Low RMS phase error: 1.2° Low insertion loss: 5 dB High linearity: +45 dBm Positive control logic 360° coverage, LSB = 5.625° 28 lead 6x6 mm SMT package: 36mm2

5.6 GHz to 8.6 GHz, GaAs, MMIC, I/Q Downconverter Features: Conversion gain: 13 dB typical Image rejection: 32 dBc typical Input P1dB compression: −6 dBm typical Input IP3: 3 dBm typical, 6.0 GHz to 8.6 GHz Noise figure: 2 dB typical LO to RF isolation: 48 dBm typical LO to IF isolation: 13 dBm typical RF to IF isolation: 10 dBm typical Amplitude balance: 0.2 dB typical Phase balance: −2° typical RF return loss: 10 dB typical LO return loss: 15 dB typical IF return loss: 15 dB typical Exposed paddle, 4 mm × 4 mm, 24-lead, LFCSP

High Precision Analog Front End Features: Analog input/output Multichannel, 16-bit, 1 MSPS SAR ADC 17 external voltage input channels 4 TIA input channels Internal channels 11 IDAC monitor channels 9 VDAC monitor channels 3 power monitor channels Single-ended mode IDACs 11 low noise, 16-bit, IDAC outputs Four channels either 0 mA to 150 mA or 0 mA to 200 mA Seven channels 0 to 20 mA or, 0 to 50 mA channels VDACs: Nine 16-bit output VDAC channels Channel 0, Channel 1, Channel 3, and Channel 4: 0 V to 5 V, 150 Ω Channel 2: 0 V to 5 V, 1 kΩ Channel 5 to Channel 8: 0 V to 2.5 V, 500 Ω On-chip voltage reference, 2.5 V SPI interface up to 40 MHz Power Multiple supplies AVDDx for VDACs and ADC to 5 V 1.65 V to AVDDx − 0.5 V for PVDD_IDACx Packages and temperature range 4.5 mm × 4.6 mm, 100-ball WLCSP Fully specified for −40°C to +120°C (TJA operation)

Quad-Channel, Software Configurable Input and Output Features: Quad-channel software configurable input/output circuit Screw terminals tolerant to ±40 V dc Line protectors to block power from the screw terminals to supplies User configurable modes Voltage input Current input Voltage output Current output Digital input RTD measurement Internal 16-bit, Σ- ADC with optional 50 Hz and 60 Hz rejection 13-bit monotonic DACs Charge pump for true zero voltage output HART-compatible Internal temperature sensor, ±5°C accuracy On-chip diagnostics including open circuit and short-circuit detection SPI-compatible Temperature range: −40°C to +105°C 64-lead LFCSP

High Performance, Multiphase Energy, and Power Quality Measurement IC Features: 7 high performance ADCs 101 dB SNR Wide input voltage range: ±1 V, 707 mV rms FS at gain = 1 Differential inputs ±25 ppm/°C maximum channel drift (including ADC, internal VREF, PGA drift) enabling 10000:1 dynamic input range Class 0.2 metrology with standard external components Power quality measurements Enables implementation of IEC 61000-4-30 Class S VRMS ½, IRMS ½ rms voltage refreshed each half cycle 10 cycle rms/12 cycle rms Dip and swell monitors Line frequency—one per phase Zero crossing, zero-crossing timeout Phase angle measurements Supports CTs and Rogowski coil (di/dt) sensors Multiple range phase/gain compensation for CTs Digital integrator for Rogowski coils Flexible waveform buffer Able to resample waveform to ensure 128 points per line cycle for ease of external harmonic analysis Events, such as dip and swell, can trigger waveform storage Simplifies data collection for IEC 61000-4-7 harmonic analysis Advanced metrology feature set Total and fundamental active power, volt amperes reactive (VAR), volt amperes (VA), watthour, VAR hour, and VA hour Total and fundamental IRMS, VRMS Total harmonic distortion Power factor Supports active energy standards: IEC 62053-21 and IEC 62053-22; EN50470-3; OIML R46; and ANSI C12.20 Supports reactive energy standards: IEC 62053-23, IEC 62053-24 High speed communication port: 20 MHz serial port interface (SPI) Integrated temperature sensor with 12-bit successive approximation register (SAR) ADC ±3°C accuracy from −40°C to +85°C

Energy Metering IC with Autocalibration Features: mSure autocalibration Automatic calibration based on a direct measurement of the full signal path Calibration procedure not requiring a reference meter mSure autocalibration Class 1 meter guaranteed 3 high performance ADCs 88 dB SNR High gain current channel: ±26.04 mV peak, 18.4 mV rms input at highest gain setting Advanced metrology feature set WATT, VAR, VA, Wh, VARh, and VAh Supports active energy standards: IEC 62053-21; IEC 62053-22; EN50470-3; OIML R46; and ANSI C12.20 Supports reactive energy standards: IEC 62053-23 and IEC 62053-24 Current and voltage rms measurement Power quality measurements Operating temperature, industrial range: −40°C to +85°C

Low Phase Noise, Fast Settling PLL Frequency Synthesizer Features: New, fast settling, fractional-N PLL architecture Single PLL replaces ping-pong synthesizers Frequency hop across GSM band in 5 µs with phase settled by 20 µs 0.5° rms phase error at 2 GHz RF output Digitally programmable output phase RF input range up to 3.5 GHz 3-wire serial interface On-chip, low noise differential amplifier Phase noise figure of merit: –216 dBc/Hz Loop filter design possible using ADIsimPLL™ Qualified for automotive applications

9.85 GHz to 20.5 GHz, Wideband, MMIC VCO Features: Wide output frequency range: 9.85 GHz to 20.5 GHz Wide tuning bandwidth Low single sideband phase noise: −83 dBc/Hz at 100 kHz offset No external resonator needed Supply current: 70 mA typical at VCC = 5 V 24-terminal, 3.90 mm × 3.90 mm, ceramic LCC package

Configurable Impedance Network Analyzer & Potentiostat with Integrated Cortex M3 Core Features: Analog performance 160 kSPS, 16-bit, precision analog-to-digital converter (ADC) 4 dedicated voltage measurement channels 8 current measurement channels Impedance measurement engine High precision voltage reference Supply noise rejection filtering Ultralow leakage configurable switch matrix 12-bit digital-to-analog converter (DAC) Precision instrumentation amplifier control loop 6-channel CapTouch controller Temperature sensor Analog hardware accelerators Autonomous analog front-end (AFE) controller Independent sequencer for AFE functions Direct digital synthesizer (DDS)/arbitrary waveform generator Receive filters Complex impedance measurement (DFT) engine Processing 16 MHz ARM Cortex-M3 processor 384 kB of embedded flash memory 32 kB system SRAM 16 kB Flash configured EEPROM Integrated full-speed USB 2.0 controller and PHY Multilayer advanced microcontroller bus architecture (AMBA) bus matrix Central direct memory access (DMA) controller Real-time clock (RTC) General-purpose, wake-up, and watchdog timers Communication Input/output I2S and beeper interface LCD display controller (parallel and serial) LCD segment controller SPI, I2C, and UART peripheral interfaces Programmable GPIOs Power Coin cell battery compatible 2.5 V to 3.6 V active measurement range Power management unit (PMU) Power-on reset (POR) and power supply monitor (PSM) Packages and temperature range Operating temperature range: −40°C to +85°C Package: 120-lead, 8 mm × 8 mm CSP_BGA