Digital to Analog Converters - DAC Quad 3V 12bit I2C DAC with reference

3.3V 20Mbps RS485/RS422 Transceiver Features: 3.3V Supply Voltage 20Mbps Maximum Data Rate No Damage or Latchup Up to ±15kV HBM High Input Impedance Supports 256 Nodes (C, IGrade) Operation Up to 125°C (H-Grade) Guaranteed Failsafe Receiver Operation Over the Entire Common Mode Range Current Limited Drivers and Thermal Shutdown Delayed Micropower Shutdown: 5μA Maximum (C, I-Grade) Power Up/Down Glitch-Free Driver Outputs Low Operating Current: 370μA Typical in Receive Mode Compatible with TIA/EIA-485-A Specifications Available in 8-Pin and 10-Pin 3mm × 3mm DFN, 8-Pin and 10-Pin MSOP, and 8-Pin and 14-Pin SO Packages

Precision Amplifiers 16V SingleLowPower/Noise AMP

Wideband, 43 dB Isolation at 1 GHz, CMOS 1.65 V to 2.75 V, 2:1 Mux/SPDT Switches Features: Wideband switch: −3 dB at 4 GHz Absorptive/reflective switches High off isolation (43 dB at 1 GHz) Low insertion loss (0.8 dB at 1 GHz) Single 1.65 V to 2.75 V power supply CMOS/LVTTL control logic 8-lead MSOP and tiny 3 mm × 3 mm LFCSP Low power consumption (<1 µA)

Linear Voltage Regulators 200mA LDO 2.75Vout

Digital to Analog Converters - DAC 10-Bit 2-ch 12c nanoDAC+with on-chip ref

Isolated Module DC DC Converter 1 Output 2.5 ~ 12V 440mA 3.1V - 31V Input

Very Low Quiescent Current, 150 mA, with Output Discharge LDO Regulator Features: Very low quiescent current IQ = 590 nA with 0 µA load IQ = 890 nA with 1 µA load Maintains very low quiescent current in dropout (pass through mode): IQ_DROP = 720 nA with 0 µA load IQ_DROP = 1200 nA with 1 µA load Stable with 1 µF ± 30% ceramic input and output capacitors Maximum load current: ILOAD_MAX: 150 mA Input voltage range: 2.2 V to 5.5 V Low shutdown current: 50 nA typical Low dropout voltage: 120 mV at 150 mA load Initial output voltage accuracy: ±1% Accuracy over line, load, and temperature: ±3.5% 7 fixed output voltage options: 1.2 V to 3.3 V Adjustable output option can be set from 1.2 V to 4.2 V See data sheet for additional features

Digital Isolators isoPower Gate Driver

Digital to Analog Converters - DAC 12-bit 4-ch SPI nanoDAC+with on-chip Ref

Multiplexer with Amplifier Interface 8-SOIC

Single Channel, 64-Position, Push-Button, 8% Resistor Tolerance, Nonvolatile Digital Potentiometer Features: Nominal resistor tolerance error: ±8% maximum Wiper current: ±6 mA Rheostat mode temperature coefficient: 35 ppm/°C Low power consumption: 2.5 μA max @ 2.7 V and 125°C Wide bandwidth: 4 MHz (5 kΩ option) Power-on EEPROM refresh time < 50 μs 50-year typical data retention at 125°C 1 million write cycles 2.3 V to 5.5 V supply operation Built-in adaptive debouncer Wide operating temperature: −40°C to +125°C Thin, 2 mm × 2 mm × 0.55 mm, 8-lead LFCSP package

AD5172 - 256-Position, One-Time Programmable, Dual-Channel, I2C Digital Potentiometer

AD518 - High Speed, Operational Amplifier

AD518 - High Speed, Operational Amplifier

Video ICs 10-Bit, 4 Oversampling SDTV Video Decoder

Precision Amplifiers Quad Precision Op Amp