Analog to Digital Converters - ADC 12-Bit 210 Msps ADC

Digital to Analog Converters - DAC DUAL 12/14 BIT D/A CONV

LC2MOS Dual 12-Bit Serial DACPORT Features: Two 12-Bit CMOS DAC Channels with On-Chip Voltage Reference Output Amplifiers Three Selectable Output Ranges per Channel -5 V to + 5 V, 0 V to +5 V, 0 V to +10 V Serial Interface 125 kHz DAC Update Rate Small Size: 16-Lead DIP or SOIC Low Power Dissipation

4 to 20mA loop buck regulator

Supervisor Open Drain or Open Collector 3 Channel 10-MSOP

Linear Voltage Regulators 150mA LDO 2.75 Vout

Buck, Boost, Cuk, Flyback, Forward Converter Switching Regulator IC Positive or Negative Adjustable 1.244V 1 Output 5A (Switch) TO-263-6, D²Pak (5 Leads + Tab), TO-263BA

COMPARATOR LOW POWER QUAD 6.75NS TSSOP-16; Comparator Type:Low Power; No. of Comparators:4; Response Time:6.75ns; Supply Voltage Range:-; Comparator Case Style:TSSOP; No. of Pins:16Pins; IC Output Type:Digital; Packaging:Cut Tape;RoHS Compliant: Yes

Compact, 800 mA, 3 MHz, Step-Down DC-to-DC Converter with an Internal Discharge Switch Features: Input voltage: 2.3 V to 5.5 V Peak efficiency: 95% 3 MHz fixed frequency operation Typical quiescent current: 24 μA Very small solution size 6-lead, 1 mm × 1.5 mm WLCSP package Fast load and line transient response 100% duty cycle low dropout mode Internal synchronous rectifier, compensation, and soft start Current overload and thermal shutdown protections Ultralow shutdown current: 0.2 μA (typical) Forced PWM and automatic PWM/PSM modes Supported by ADIsimPower™ design tool

Temp Monitoring System (Sensor) -40°C ~ 120°C Internal and External Sensor I²C, MICROWIRE, QSPI, SPI Output 16-QSOP

2.7 V, 800 A, 80 MHz Rail-to-Rail I/O Single Amplifier Features: Low power Supply current 800 µA/amplifier Fully specified at +2.7 V, +5 V and ±5 V supplies High speed and fast settling on 5 V 80 MHz, –3 dB bandwidth (G = +1) 30 V/µs slew rate 125 ns settling time to 0.1% Output current: 15 mA High grade option VOS (maximum) = 1.5 mV Rail-to-rail input and output No phase reversal with input 0.5 V beyond supplies Input CMVR extends beyond rails by 200 mV Output swing to within 20 mV of either rail Low distortion –62 dB @ 1 MHz, VO = 2 V p-p –86 dB @ 100 kHz, VO = 4.6 V p-p

Quad Voltage Microprocessor Supervisory Circuit Features: Accurate monitoring of up to four power supply voltages 6 factory-set threshold options: −5.0 V, 1.8 V, 2.5 V, 3.0 V, 3.3 V, and 5.0 V Adjustable input threshold options: −0.5 V (±2.0% accuracy), 0.62 V (±0.8% accuracy), and 1.23 V 200 ms typical reset timeout Open-drain RESET output (10 μA internal pull-up) Reset output stage: active low, valid to IN1 = 1 V or IN2 = 1 V Low power consumption (55 μA) Glitch immunity Specified from −40°C to +85°C

Analog to Digital Converters - ADC 16-Bit 250 KSPS Serial MSOP I.C.

Dual-Channel Isolators with Integrated DC-to-DC Converter (1/1 channel directionality) Features: isoPower® integrated isolated DC/DC converter Regulated 3V or 5V output Up to 500 mW output power 16-lead SOIC package with 7.6 mm creepage Dual dc-to-25 Mbps (NRZ) signal isolation channels High temperature operation: 105°C maximum High common-mode transient immunity: > 25 kV/µsSafety and regulatory approvals UL recognition 2500 V rms for 1 minute per UL 1577 VDE cert of conformity (pending) IEC 60747-5-2 (VDE V 0884-10):2006-12 VIORM = 560 VPEAK See data sheet for additional features

Digital to Analog Converters - DAC Octal 16bit I2C DAC w ref & clr midscale

Lc2Mos Complete, 8-Bit Analog I/O System

Boost Switching Regulator IC Positive Fixed 3.3V 1 Output 140mA 6-VSSOP, SC-88, SOT-363