Micropower, 3-Axis, 400 g, Digital Output, MEMS Accelerometer Features: ±400 g measurement range 160 Hz to 2560 Hz user selectable bandwidth with 4-pole antialiasing filter Selectable oversampling ratio Adjustable high-pass filter Ultra Low power Power can be derived from a coin cell battery 19 μA at 2560 Hz ODR, 2.5 V supply Low power wake-up mode for low g activity detection 1.4 μA instant on mode with adjustable threshold 0.1 μA standby mode Built-in features for system level power savings Autonomous interrupt processing without processor intervention Ultra low power event monitoring: detects impacts and wakes up fast enough to capture the transient events Adjustable low g threshold activity and inactivity detection Wide operating voltage range: 1.6 V to 3.5 V Acceleration sample synchronization via external trigger SPI digital interface and I2C interface format support 12-bit output at 200 mg/LSB scale factor Wide temperature range: −40°C to +105°C Small, thin 3.00 mm × 3.25 mm × 1.06 mm package

3-Axis, 200 g Digital MEMS Accelerometer Features: Low power: as low as 35 µA in measurement mode and 0.1 µA in standby mode at VS = 2.5 V (typical) Power consumption scales automatically with bandwidth Embedded, 32-level FIFO buffer minimizes processor load Bandwidth of up to 1 kHz Bandwidth selectable via serial command Shock event detection Activity/inactivity monitoring Supply voltage range: 2.0 V to 3.6 V I/O voltage range: 1.7 V to VS SPI (3- or 4-wire) and I2C digital interfaces Wide temperature range: −40°C to +85°C 10,000 g shock survival Pb free/RoHS compliant Small and thin: 3 mm × 5 mm × 1 mm LGA packageADXL375-EP supports defense and aerospace applications (AQEC standard)Download ADXL375-EP Data Sheet (pdf)Extended industrial temperature range: −55°C to +105°CControlled manufacturing baseline1 assembly/test site1 fabrication siteProduct change notificationQualification data available on requestV62/ 18612 DSCC Drawing Number

I2C to CAN-Physical Transceiver Features: Protected from Overvoltage Line Faults to ±40V Up to 400kbps I2C Communications 4V to 60V Power Supply Range with Internal 3.3V Regulator 3.3V or 5V Bus Voltage Extended Common Mode Range (±36V) Current Limited Drivers with Thermal Shutdown Power-Up/Down Glitch Free Driver Outputs Low Current Shutdown Mode Transmit Data Dominant Timeout Function E- and J-Grades Available Available in a 10-Lead MSOP Package AEC-Q100 Qualification in Progress

40VIN, 18VOUT, 6A Synchronous Buck-Boost Silent Switcher Features: 4-Switch Single Inductor Architecture Allows VIN Above, Below or Equal to VOUT Silent Switcher® Architecture for Low EMI Up to 95% Efficiency at 2MHz Proprietary Peak Current Mode 3V to 40V Input Voltage Range 1V to 18V Output Voltage Range ±1.5% Output Voltage Regulation Output/Input Current Regulation and Monitor Constant-Voltage/Constant-Current Regulation High Side PMOS Load Switch Driver No Top MOSFET Refresh Noise in Buck or Boost 200kHz to 2MHz Fixed Switching Frequency with External Frequency Synchronization and SSFM VOUT Disconnected from VIN During Shutdown Small 4mm × 6mm 32-Pin LQFN Package AEC-Q100 Qualification in Progress

42V Quad, Gangable, Synchronous, Monolithic Step-Down Regulator Features:Silent Switcher2 ArchitectureUltralow EMI EmissionsOptional Spread Spectrum ModulationTwo High Voltage Synchronous Buck Regulators3V to 42V Input Voltage RangeOutput Currents Up to 2.5A per ChannelChannels May Be Connected in Parallel Using a Single InductorTwo Low Voltage Synchronous Buck Regulators3V to 8V Input Voltage RangeOutput Currents Up to 4A per ChannelChannels May Be Connected in Parallel Using a Single Inductor12A IQ All Channels Active and No-LoadFlexible Supply Sequencing and ControlAdjustable and Synchronizable: 350kHz to 3MHzAvailable in 36-Lead LQFN (5mm 6mm)AEC-Q100 Qualified for Automotive Applications

20-Bit Power No Latency ADC in SO-8 Features: 20-Bit ADC in SO-8 Package 8ppm INL, No Missing Codes at 20 Bits 4ppm Full-Scale Error 0.5ppm Offset 1.2ppm Noise Digital Filter Settles in a Single Cycle. Each Conversion Is Accurate, Even After an Input Step Fast Mode: 16-Bit Noise, 12 Bits TUE at 100sps Internal Oscillator—No External Components Required 110dB Min, 50Hz/60Hz Notch Filter Reference Input Voltage: 0.1V to VCC Live Zero—Extended Input Range Accommodates 12.5% Overrange and Underrange Single Supply 2.7V to 5.5V Operation Low Supply Current (200µA) and Auto Shutdown Pin Compatible with 24-Bit LTC2400

0.88nV/Hz 730MHz, 500V/s, Low Distortion Rail-to-Rail Output Op Amps with Shutdown Features: Ultra Low Voltage Noise: 0.88nV/√Hz Low Distortion at High Speeds: HD2/HD3 < −100dBc (Av = +1, 4VP-P, 2MHz, RL = 1kΩ) High Slew Rate: 500V/μs GBW = 890MHz –3dB Frequency (AV = +1): 730MHz Input Offset Voltage: 250μV Max Across Temperature Offset Drift :0.4μV/°C Input Common Mode Range Includes Negative Rail Output Swings Rail-to-Rail Supply Current: 16mA/Channel Typ Shutdown Supply Current = 500µA Operating Supply Range: 2.8V to 11.75V Large Output Current: 80mA Min Very High Open Loop Gain: 5.6V/μV (135dB), RL = 1kΩ Operating Temp Range: –40°C to 125°C Singles in 8-Lead SOIC, TSOT-23, DC-6, Duals in DD10, MS8

0.88nV/Hz 730MHz, 500V/s, Low Distortion Rail-to-Rail Output Op Amps with Shutdown Features: Ultra Low Voltage Noise: 0.88nV/√Hz Low Distortion at High Speeds: HD2/HD3 < −100dBc (Av = +1, 4VP-P, 2MHz, RL = 1kΩ) High Slew Rate: 500V/μs GBW = 890MHz –3dB Frequency (AV = +1): 730MHz Input Offset Voltage: 250μV Max Across Temperature Offset Drift :0.4μV/°C Input Common Mode Range Includes Negative Rail Output Swings Rail-to-Rail Supply Current: 16mA/Channel Typ Shutdown Supply Current = 500µA Operating Supply Range: 2.8V to 11.75V Large Output Current: 80mA Min Very High Open Loop Gain: 5.6V/μV (135dB), RL = 1kΩ Operating Temp Range: –40°C to 125°C Singles in 8-Lead SOIC, TSOT-23, DC-6, Duals in DD10, MS8

Digital Input Stereo, 2 W, Class-D Audio Power Amplifier Features: Filterless, digital input Class-D amplifier Serial digital audio interface supports common formats: I2S, left justified, right justified, TDM1-16, and PCM 2 channels × 2 W into 4 Ω and 2 channels × 1.4 W into 8 Ω with 1% THD+N, when using a 5 V supply I2C control interface or standalone operation 91% efficiency at full scale into an 8 load 97 dB signal-to-noise ratio (SNR), A-weighted 80 dB power supply rejection ratio (PSRR) at 217 Hz Digital volume control: −71.25 dBto +24 dBin 0.375 dBsteps Supports a wide range of sample rates from 8 kHz to 96 kHz Automatic sample rate detection Can operate using 64 × fS BCLK as the MCLK source 2.5 V to 5.5 V speaker supply voltage (PVDD) 1.62 V to 3.6 V digital supply voltage (DVDD) Pop-and-click suppression Short-circuit and thermal protection with programmable autorecovery Smart power-down when no input signal is detected Power-on reset Low power modes for performance/power trade-offs User selectable ultralow EMI emission mode Programmable dynamic range compression (DRC) with noise gate, expander, compressor, and limiter Available in two packages 16-bump, 2.2 mm × 2.2 mm, 0.5 mm pitch WLCSP 20-lead, 4.0 mm × 4.0 mm LFCSP

Ultralow Noise, Low Power Current Amplifier Features: Ultralow noise, low power current amplifier 80 fA/√Hz (typical) noise floor 140 μA (typical) of supply current when active (EE = 0 μW/cm2) 100 nA (typical) of supply current in standby Flexible output configuration Optimized for pulsed systems Nominal linear output: 240 μA Space-saving 2 mm × 2 mm LFCSP package

Ultra Low Power ARM Cortex-M4F MCU with Integrated Power Management Features: EEMBC ULPMark™-CP score (3 V): 189 Ultra low power active and hibernate modes Active mode dynamic current: 41 μA/MHz (typical) Flexi mode: 400 μA (typical) Hibernate mode: 0.65 μA (typical) Shutdown mode: 50 nA (typical) Shutdown mode (fast wake-up): 0.20 μA (typical) ARM Cortex-M4F processor at 52 MHz with FPU, MPU, ITM with SWD interface Power management Single-supply operation (connected to VBAT pins): 1.74 V to 3.6 V Optional buck converter for improved efficiency Memory options 512 kB of embedded flash memory with ECC 4 kB of cache memory to reduce active power 128 kB of configurable system SRAM with parity Safety Watchdog with dedicated on-chip oscillator Hardware CRC with programmable polynomial Multiparity bit protected SRAM ECC protected embedded flash Security Hardware cryptographic accelerator supporting AES-128, AES-256, and SHA-256 Protected key storage in flash, SHA-256-based keyed HMAC and key wrap and unwrap User code protection TRNG Digital peripherals 3 SPI interfaces to enable glueless interface to sensors, radios, and converters 1 I2C and 2 UART peripheral interfaces SPORT for natively interfacing with converters and radios Programmable GPIOs (44 in LFCSP and 51 in WLCSP) 3 general-purpose timers with PWM support RGB timer for driving RGB LED RTC0 for time keeping RTC1 with SensorStrobe and time stamping Programmable beeper 27-channel DMA controller Clocking features 26 MHz clock: on-chip oscillator, external crystal oscillator, SYS_CLKIN for external clock, and integrated PLL 32 kHz clock: on-chip oscillator and low power crystal oscillator Clock fail detection for external crystals Analog peripherals 12-bit SAR ADC, 1.8 MSPS, 8 channels, and digital comparator

SmartMesh IP Wireless 802.15.4e PCBA Module with Antenna Connector Features: 37mm × 24mm PCBA module with MMCX antenna connector Integrates 2.4 GHz, IEEE 802.15.4e System-on-Chip, Complete with Embedded SmartMesh Networking Software >99.999% Network Reliability in the Most Challenging RF Environments Sub 50µA Routing Nodes Serves as either a Wireless Mote, EManager, or Access Point Mote in a SmartMesh IP network These products contain encryption. Import/export restrictions may apply.

High Performance, Low Power, ISM Band FSK/GFSK/OOK/MSK/GMSK Transceiver IC Features: Ultralow power, high performance transceiver Frequency bands 862 MHz to 928 MHz 431 MHz to 464 MHz Data rates supported 1 kbps to 300 kbps 2.2 V to 3.6 V power supply Single-ended and differential PAs Low IF receiver with programmable IF bandwidths 100 kHz, 150 kHz, 200 kHz, 300 kHz Receiver sensitivity (BER) −116 dBm at 1.0 kbps, 2FSK, GFSK −107.5 dBm at 38.4 kbps, 2FSK, GFSK −102.5 dBm at 150 kbps, GFSK, GMSK −100 dBm at 300 kbps, GFSK, GMSK −104 dBm at 19.2 kbps, OOK Very low power consumption RF output power of −20 dBm to +13.5 dBm (single-ended PA) See data sheet for additional Features

Ultra Low Power ARM Cortex-M3 MCU with Integrated Power Management and 256 KB of Embedded Flash Memory Features: EEMBC ULPMark™-CP score: 245.5 Ultra low power active and hibernate mode Active mode dynamic current: 30 μA/MHz (typical) Flexi mode: 300 μA (typical) Hibernate mode: 750 nA (typical) Shutdown mode: 60 nA (typical) ARM Cortex-M3 processor with MPU Up to 26 MHz with serial wire debug interface Power management Single-supply operation (VBAT): 1.74 V to 3.6 V Optional buck converter for improved efficiency Memory options 128 kB/256 kB of embedded flash memory with ECC 4 kB of cache memory to reduce active power 64 kB of configurable system SRAM with parity up to 32 kB of SRAM retained in hibernate mode Safety Watchdog with dedicated on-chip oscillator Hardware CRC with programmable polynomial Multiparity bit protected SRAM ECC protected embedded flash Security TRNG User code protection Hardware cryptographic accelerator supporting AES-128, AES-256, and SHA-256 Digital peripherals 3 SPI interfaces to enable glueless interface to sensors, radios, and converters I2C and UART interfaces SPORT for natively interfacing with converters and radios Programmable GPIOs (44 in LFCSP and 34 in WLCSP) 3 general-purpose timers with PWM support RTC and FLEX_RTC with SensorStrobe and time stamping Programmable beeper 25-channel DMA controller Clocking features 26 MHz clock: on-chip oscillator, external crystal oscillator 32 kHz clock: on-chip oscillator, low power crystal oscillator Integrated PLL with programmable divider Analog peripherals 12-bit SAR ADC, 1.8 MSPS, 8 channels, and digital comparator 

High Performance, Sub GHz Radio Transceiver IC Features: Radio frequency (RF) ranges 169.4 MHz to 169.6 MHz 426 MHz to 470 MHz 863 MHz to 960 MHz Data rates 2FSK/2GFSK: 0.1 kbps to 300 kbps 4FSK/4GFSK: 1 kbps to 360 kbps (transmit only) Dual power amplifiers (PAs) Programmable receiver channel bandwidth from 2.6 kHz to 406 kHz Receiver (Rx) performance Up to 97 dB blocking at ±20 MHz offset Up to 72 dB adjacent channel rejection −134.3 dBm sensitivity at 0.1 kbps −121.3 dBm sensitivity at 2.4 kbps Transmitter (Tx) performance −20 dBm to +17 dBm range with 0.1 dB step resolution Very low output power variation vs. temperature and supply Low active current 50 mA Tx current at 17 dBm 21.2 mA Rx current at12.5 kbps Ultralow sleep current 10 nA with memory retained Host microprocessor interface Easy to use programming serial peripheral interface (SPI) Configurable 8-bit general-purpose input/output (GPIO) bus On-chip ARM Cortex-M0 processor for  Radio control and calibration Packet management Clear channel assessment (CCA) IEEE802.15.4g support Frame format  Data whitening Dual-sync word detection Forward error correction (FEC) and interleaving Suitable for systems targeting compliance with ETSI EN 300 220-1 EN 54-25, EN 13757-4 FCC Part 15, Part 22, Part 24, Part 90, and Part 101  ARIB STD-T30, STD-T67, STD-T108, STD-T96 Packages 6 mm × 6 mm, 40-lead LFCSP 7 mm × 7 mm, 48-lead LQFP

High Performance, Sub GHz Radio Transceiver IC Features: Radio frequency (RF) ranges 169.4 MHz to 169.6 MHz 426 MHz to 470 MHz 863 MHz to 960 MHz Data rates 2FSK/2GFSK: 0.1 kbps to 300 kbps 4FSK/4GFSK: 1 kbps to 360 kbps (transmit only) Dual power amplifiers (PAs) Programmable receiver channel bandwidth from 2.6 kHz to 406 kHz Receiver (Rx) performance Up to 97 dB blocking at ±20 MHz offset Up to 72 dB adjacent channel rejection −134.3 dBm sensitivity at 0.1 kbps −121.3 dBm sensitivity at 2.4 kbps Transmitter (Tx) performance −20 dBm to +17 dBm range with 0.1 dB step resolution Very low output power variation vs. temperature and supply Low active current 50 mA Tx current at 17 dBm 21.2 mA Rx current at12.5 kbps Ultralow sleep current 10 nA with memory retained Host microprocessor interface Easy to use programming serial peripheral interface (SPI) Configurable 8-bit general-purpose input/output (GPIO) bus On-chip ARM Cortex-M0 processor for  Radio control and calibration Packet management Clear channel assessment (CCA) IEEE802.15.4g support Frame format  Data whitening Dual-sync word detection Forward error correction (FEC) and interleaving Suitable for systems targeting compliance with ETSI EN 300 220-1 EN 54-25, EN 13757-4 FCC Part 15, Part 22, Part 24, Part 90, and Part 101  ARIB STD-T30, STD-T67, STD-T108, STD-T96 Packages 6 mm × 6 mm, 40-lead LFCSP 7 mm × 7 mm, 48-lead LQFP

RapID Platform Generation 2 (RPG2) Network Interface Features: Configurable industrial protocol support PROFINET RT (Class B) PROFINET IRT (Class C): coming soon EtherNet/IP with DLR EtherCAT All protocols precertified Configurable applications processor interface UART: 115,200 bps to 1,000,000 bps Ethernet at 10 Mbps or 100 Mbps SPI follower: 10 MHz maximum clock I2C, QSPI, and CAN: future option Industrial Ethernet interface-compliant to IEEE 802.3, 10Base or 100Base transmit half and full duplex Single 3.3 V power supply, 840 mW Cycle time down to 1 ms (cycle times vary based on protocol, link type, and application data) 194-ball chip-scale package BGA form factor RoHS 3 compliant –40°C to +85°C industrial temperature range

RapID Platform Generation 2 (RPG2) Network Interface Features: Configurable industrial protocol support PROFINET RT (Class B) PROFINET IRT (Class C): coming soon EtherNet/IP with DLR EtherCAT All protocols precertified Configurable applications processor interface UART: 115,200 bps to 1,000,000 bps Ethernet at 10 Mbps or 100 Mbps SPI follower: 10 MHz maximum clock I2C, QSPI, and CAN: future option Industrial Ethernet interface-compliant to IEEE 802.3, 10Base or 100Base transmit half and full duplex Single 3.3 V power supply, 840 mW Cycle time down to 1 ms (cycle times vary based on protocol, link type, and application data) 194-ball chip-scale package BGA form factor RoHS 3 compliant –40°C to +85°C industrial temperature range

RapID Platform Generation 2 (RPG2) Network Interface Features: Configurable industrial protocol support PROFINET RT (Class B) PROFINET IRT (Class C): coming soon EtherNet/IP with DLR EtherCAT All protocols precertified Configurable applications processor interface UART: 115,200 bps to 1,000,000 bps Ethernet at 10 Mbps or 100 Mbps SPI follower: 10 MHz maximum clock I2C, QSPI, and CAN: future option Industrial Ethernet interface-compliant to IEEE 802.3, 10Base or 100Base transmit half and full duplex Single 3.3 V power supply, 840 mW Cycle time down to 1 ms (cycle times vary based on protocol, link type, and application data) 194-ball chip-scale package BGA form factor RoHS 3 compliant –40°C to +85°C industrial temperature range

Real-Time Ethernet Multiprotocol (REM) Switch Features: 144-lead CSP_BGA RoHS compliant package −40°C to +105°C industrial temperature range rating 3.3 V input/output buffers IEEE 802.3, 10 Mbps/100 Mbps, half and full duplex, IPv6 and IPv4 communication 2 independent Ethernet ports: 1 MII and 1 RMII interface per port Support for all industrial protocols PROFINET Class B and Class C with fast startup (Version 2.3) EtherNet/IP with QuickConnect, CIP Sync, and CIP Motion Modbus TCP EtherCAT Ethernet POWERLINK Host interface transfer rate: 32 bits per 28 ns Supports EtherCAT cycle times down to 12.5 μs and PROFINET cycle times down to 31.25 μs PI Net Load Class III capable DLR (supervisor and node, announce and beacon based), MRPD, HSR, PRP, shared device, controller redundancy IEEE 1588Version 2 support: ordinary clock; both peerto peer and end to end transparent clocks, raw frames, and UDP 8 independent timer signals synchronized with an internal precision timer 4 independently programmable timer signals for timer capture events or timer output events 4 timer signals create programmable periodic waveforms synchronized to the internal precision timer DCP, LLDP, DHCP, RSTP, VLAN, IGMP snooping support Forwarding table with aging and learning Drive LEDs for link activity