IC Operational Amplifier DUAL CMOS TSSOP 8PIN PLASTIC

Voltage References 4.096V Shunt Voltage Ref

Precision Amplifiers DUAL High Performance ZCO Op Amp

Operational Amplifiers - Op Amps High Spd CMOS RR Video Amp

Triple Differential Receiver with Adjustable Line Equalization Features: Compensates cables to 300 meters for wideband video Fast rise and fall times 4.9 ns with 2 V step at 150 meters of UTP cable 8.0 ns with 2 V step at 300 meters of UTP cable 55 dB peak gain at 100 MHz Two frequency response gain adjustment pins High frequency peaking adjustment (VPEAK) Broadband flat gain adjustment (VGAIN) Pole location adjustment pin (VPOLE) Compensates for variations between cables Can be optimized for either UTP or coaxial cable DC output offset adjust (VOFFSET) Low output offset voltage: 24 mV Compensates both RGB and YPbPr Two on-chip comparators with hysteresis Can be used for common-mode sync extraction Available in 40-lead, 6 mm × 6 mm LFCSP

AD1865 - Dual 18-Bit 16 X FS Audio DAC

High Voltage, 1.2 MHz/600 kHz, 800 mA, Low Quiescent Current Buck Regulator with Quick Output Discharge Function Features: Input voltage range: 3.2 V to 15 V, output current: 800 mA Quiescent current < 14 µA in power saving mode (PSM) >90% efficiency Force PWM pin (SYNC), 600 kHz/1.2 MHz frequency pin (FSEL) Fixed outputs: 0.8 V, 1.2 V, 1.5 V, 1.8 V, 2.5 V, 3.0 V, 3.3 V, 5 V, and adjustable option 100% duty cycle capability Initial accuracy: ±1% Low shutdown current: <1.2 µA Quick output discharge (QOD) option Synchronizable to an external clock 8-lead, 0.75 mm × 3 mm × 3mm LFCSP (QFN) package Supported by ADIsimPower design tool

Precision Amplifiers Dual Low Voltage Micropower OP Amp

Precision Amplifiers DUAL PRECISION LOW IB OP

2-ChANNEL ISO W/INTEGRATED DC/DC ;RoHS Compliant: Yes

Oscillator, Silicon IC 100kHz ~ 20MHz 10-MSOP

Isolated Switching Regulators (3/1 Channel Directionality) Features: Isolated PWM Controller Integrated transformer driver Regulated adjustable output: 3.3 V to 24 V 2 W output power 70% efficiency at guaranteed load of 400 mA at 5.0 V output Quad dc-to-25 Mbps (NRZ) signal isolation channels 20-lead SSOP package High temperature operation: 105°C High common-mode transient immunity: >25 kV/μs 200 kHz to 1 MHz adjustable oscillator frequency Soft start function at power-up Pulse-by-pulse overcurrent protection Thermal shutdown 2500 V rms isolation Evaluation Board available Automotive Qualified

AD5625 - Quad, 12-Bit nanoDACS with 5 PPM/Degree Celsius On-Chip Reference, I2C Interface

Super Sequencer and Monitor with Margining Control and Non-Volatile Fault Recording Features: Complete supervisory and sequencing solution for up to 8 supplies 16 event deep black box nonvolatile fault recording 8 supply fault detectors enable supervision of supplies to: < 0.5% accuracy at all voltages at 25°C; < 1.0% accuracy across all voltages and temperatures 4 selectable input attenuators allow supervision of supplies to: 14.4 V on VH; 6 V on VP1 to VP3 (VPx) 8 programmable driver outputs, PDO1 to PDO8 (PDOx) Sequencing engine (SE) implements state machine control of PDO outputs: conditional on input events; Power-up and power-down sequence control; Fault event handling; Interrupt on warnings; Watchdog can be integrated in SE; software control through SMBus User EEPROM: 256 bytes Complete voltage margining solution for 4 voltage rails 4 voltage output 8-bit DACs (0.300 V to 1.551 V) allow voltage adjustment via dc-to-dc converter trim/feedback node 12-bit ADC for readback of all supervised voltages Reference input (REFIN) has 2 input options: Driven directly from 2.048 V (±0.25%) REFOUT pin; More accurate external reference for improved ADC performance Device powered by the highest of VPx, VH for improved redundancy Industry-standard 2-wire bus interface (SMBus) Guaranteed PDO low with VH, VPx = 1.2 V 4 dual-function inputs, VX1 to VX4 (VXx): High impedance input to supply fault detector with thresholds between 0.573 V and 1.375 V; General-purpose logic input

AD9762 - 12-Bit, 100MSPS+ TxDAC D/A Converter