Search results

MSP430 Metering Application Report

This design notes shows the hot swap designer how to control a ?5V rail using a UCC3919 Hot Swap Power Manager. This technique could also be applied using other positive Hot Swap Power Managers. Two c

PMP7892 is an isolated active clamp forward converter capable of 42W output power. This design uses the LM5026 active clamp current-mode controller. Output voltage regulation is maintained using an LMV431 shunt regulator and opto-coupler feedback. Schottky rectifiers allow for holdup of 10ms using the stored charge of the output capacitors. The isolation voltage is 2250 VDC meeting basic insulation requirements.

Demonstration circuit 1614 features the LTC4012CUF, a multi-chemistry single battery charger controller with PowerPath™ control. The input supply voltage is 13.5V to 20V and is initially configured for a current limit of 10A. The charger float voltage is programmed by jumpers to support 1- to 4- series cells of both Li-Ion/Polymer and Li-iron phosphate (LiFePO4) at 4.2V/cell and 3.6V/cell, for a total of eight settings. The demo board is initially configured for constant-voltage charging of a 12.6V Li-Ion/ Polymer battery and constant-current charging at 8A, though current derating may be necessary due to certain operating conditions.

This EBV designed board is the ideal board to start first experiments based on Altera Cyclone III FGPAs.

The AD5590 is a 16-channel input and 16-channel output analog I/O port with eight uncommitted amplifiers, operating from a single 4.5 V to 5.25 V supply. The AD5590 comprises 16 input channels multiplexed into a 1 MSPS, 12-bit successive approximation ADC with a sequencer to allow a preprogrammed selection of channels to be converted sequentially. The ADC contains a low noise, wide bandwidth track-and-hold amplifier that can handle input frequencies in excess of 1 MHz.The conversion process and data acquisition are controlled using ASYNC and the serial clock signal, allowing the device to easily interface with microprocessors or DSPs. The input signal is sampled on the falling edge of ASYNC and conversion is also initiated at this point. There are no pipeline delays associated with the ADC. By setting the relevant bits in the control register, the analog input range for the ADC can be selected to be a 0 V to VREFA input or a 0 V to 2 ? VREFA with either straight binary or twos complement output coding. The conversion time is determined by the ASCLK frequency because it is also used as the master clock to control the conversion.The DAC section of the AD5590 comprises sixteen 12-bit DACs divided into two groups of eight. Each group has an on-chip reference. The on-board references are off at power-up, allowing the use of external references. The internal references are enabled via a software write.The AD5590 incorporates a power-on reset circuit that ensures that the DAC outputs power up to 0 V and remain powered up at this level until a valid write takes place. The DAC contains a power-down feature that reduces the current consumption of the device and provides software-selectable output loads while in power-down mode for any or all DAC channels. The outputs of all DACs can be updated simultaneously using the LDAC function, with the added functionality of user-selectable DAC channels to simultaneously update. There is also an asynchronous CLR that updates all DACs to a user-programmable code: zero scale, midscale, or full scale.The AD5590 contains eight low noise, single-supply amplifiers. These amplifiers can be used for signal conditioning for the ADCs, DACs, or other independent circuitry, if required.APPLICATIONS Optical Line Cards (Monitoring and Control) Base Stations General Purpose Analog I/O Monitoring and control

DC1370A-H: Demo Board for the LTC2260-12 12-Bit, 105Msps Ultralow Power 1.8V ADCs

PMP5140 is a single-phase synchronous switching regulator accepting input voltages of 3.3Vin or 12Vin and providing an output voltage of 1.2Vout capable of supplying 10A of current.

The Supercapacitor Manager is a fully integrated: single-chip: solution that provides a rich array of features for managing: charge control: monitoring: and protection: for either 2: 3: 4 or 5 series Supercapacitors with individual capacitor monitoring and balancing or up to 9 series capacitors with only the stack voltage being measured.

This application report explains how use TI’s reliability de-rating tools to calculate a component level FIT under power on conditions for a system mission profile.

The ADF4360-2 is a fully integrated integer-N synthesizerand voltage-controlled oscillator (VCO). The ADF4360-2 isdesigned for a center frequency of 2000 MHz. In addition, adivide-by-2 option is available, whereby the user gets an RFoutput of between 925 MHz and 1085 MHz.Control of all the on-chip registers is through a simple 3-wireinterface. The device operates with a power supply rangingfrom 3.0 V to 3.6 V and can be powered down when not in use.Applications Wireless handsets (DECT, GSM, PCS, DCS, WCDMA) Test equipment Wireless LANs CATV equipment

The ADAU1472 is a high quality SigmaDSP? digital audio?processor with a large internal memory, enabling efficient audio?source separation, far field voice capture, speech processing, deep?learning, and advanced audio signal processing. The processor combines the highly optimized Cadence? Tensilica? HiFi? 4?audio/voice processor with custom Analog Devices, Inc.,?instruction extensions for math acceleration, and a flexible input and output architecture. The?HiFi 4 processor supports four 32-bit ? 32-bit multiplier?accumulators (MACs) per cycle with 72-bit accumulators, dual 64-bit memory load, and a native Institute of Electrical and?Electronics Engineers (IEEE) single precision, floating-point multiplier.The ADAU1472 processor offers performance up to 270.336 MHz,?supports low latency, sample by sample audio processing, and?block by block processing paradigms in parallel. The integer?phase-locked loop (PLL) and flexible clock generator hardware?can generate up to 15 audio sample rates simultaneously (8 kHz?to 192 kHz). These clock generators, along with the on-board?asynchronous sample rate converters (ASRCs) and flexible?hardware audio routing matrix, greatly simplify the design of?complex audio systems.The HiFi 4 digital signal processor (DSP) core has 480 kB of L1?memory running at the DSP core clock rate, which consists of?256 kB data random access memory (RAM), 64 kB instruction?RAM, 128 kB data cache, and 32 kB instruction cache, along with?2 MB of L2 system static random access memory (SRAM)?running at one half of the DSP core clock rate. The processor?also supports up to 2 GB of external flash memory to enable the?storage of large data tables and self boot code.Dual on-chip power domains allow low power operation,?including the capability of routing audio through a flexible audio?routing matrix with IOVDD as the only active supply.?The configurable voice detection hardware can detect human?speech onset while operating in a low power state and can?generate both internal DSP and external wake-up signals.The ADAU1472 interfaces with a wide range of analog-to-digital?converters (ADCs), digital-to-analog converters (DACs), digital?audio devices, amplifiers, and control circuitry due to its highly?configurable serial ports, Sony/Philips digital interface?format (S/PDIF) interfaces, and multipurpose input/output?pins. The device can also directly interface with up to 14 pulse?density modulated (PDM) output microphones due to?integrated decimation filters specifically designed for that?purpose. The PDM outputs with integrated interpolation filters?provide direct connectivity to PDM input Class D amplifiers.The processor has two serial peripheral interface (SPI) bus master?control ports that allow the device to communicate with multiple?SPI-compatible devices including support for single, dual, and?quad input/output operation. In addition, the SPI flash port?allows direct memory mapped read access with minimal central?processing unit (CPU) overhead and standalone self boot?operation.The combined high performance DSP core, large RAM, and?small footprint make the ADAU1472 an ideal replacement for?large, general-purpose DSPs that consume more power for the?same processing load.Applications Far field voice interface devices Audio source separation Embedded deep learning for audio Commercial and professional audio processing

UCC28950, UCC29002, UCC39002 Pre-biased Output Voltage Startup Operation of the UCC28950

This PMP5643 is a universal mains quasi-resonant isolated flyback: delivering a peak power of 51W and 37W average @ 13.65V. The converter benefits from the cascode" topology to reduce further the no-load losses and to achieve very fast startup time."