Search results

The VCA8613 is an 8-channel variable gain amplifier ideally suited for portable and mid-range ultrasound applications. Each channel consists of a Low Noise Amplifier (LNA) and a Variable Gain Amplifier (VGA). The VGA contains two parts: a voltage-controlled attenuator (VCA) and a programmable gain amplifier (PGA). The PGA output feeds directly into an integrated 2-pole low-pass Butterworth filter.

This converter is used for Class 2 or 3 PoE applications. The flyback converter with diode rectifier offers low cost while still achieving good efficiency. This converter is well sutied for PoE applications such as IP phones. The TPS23753A contains both the PoE Powered Device and the PWM controller functions.

The AD4114 is a low power, low noise, 24-bit, sigma-delta (?-?) analog-to-digital converter (ADC) that integrates an analog front end (AFE) for eight fully differential or 16 single-ended, high impedance (?1 M?), bipolar, ?10 V voltage inputs.The AD4114 integrates key analog and digital signal conditioning blocks to configure eight individual setups for each analog input channel in use. The AD4114 features a maximum channel scan rate of 6.21 kSPS (161 ?s) for fully settled data.The embedded 2.5 V, low drift (?5 ppm/?C), band gap internal reference (with output reference buffer) reduces the external component count.The digital filter allows flexible settings, including simultaneous 50 Hz and 60 Hz rejection at a 27.27 SPS output data rate. The user can select different filter settings depending on the requirements of each channel in the application. The automatic channel sequencer enables the ADC to switch through each enabled channel.The precision performance of the AD4114 is achieved by integrating the proprietary iPassives? technology from Analog Devices, Inc. The AD4114 is factory calibrated to achieve a high degree of specified accuracy.The AD4114 operates with a single power supply that allows simplified use in galvanically isolated applications. The specified operating temperature range is ?40?C to +105?C. The AD4114 is housed in a 40-lead, 6 mm ? 6 mm LFCSP.ApplicationsProgrammable logic controller (PLC) and distributed control system (DCS) modules Instrumentation and measurement

Demonstration circuit 1349A is a polyphase 3-output step-down supply with tracking featuring the LTC3853EUJ. The input voltage range is 6.5V to 14V. For applications with narrow, 5V ±0.5V input range, the board has an optional resistor to tie the INTVCC pin to the VIN pin. The demo board provides three 15A outputs, with output voltages of 1.8V, 1.2V and 2.5V. The main features of the board include rail tracking, an internal 5V linear regulator for bias, RUN pins for each output, two PGOOD signals and a Mode selector that allow the converter to run in CCM, pulse skip or Burst Mode operation. Synchronization to an external clock is also possible through some minor component changes.

DRV8711 DRV8711 Quick Spin and Tuning Guide

Texas Instruments offers low-cost: low-power: integrated multichannel reference designs featuring the Hybrid DVR (DVR/NVR) reference design based on the highly integrated TMS320DM816x and TMS320DM8107 DaVinci™ video processors. This single platform solution allows faster development at a reduced cost.DM8107 DVR Reference DesignOrder NowPart number:DM8107DVR-UD1Price:$1095Description:Single platform solution based on the TMS320DM8107 DaVinci video processor provides configurations for 4/8/16 channel DVRs. Provide 1000fps CIF H.264/SVCT encode/decode with integrated HDMI/VGA/CVBS output on a single processor.Processors:New low power: cost optimized DM8107 processor and new TVP5158 multi-channel video decoder with integrated audio. DM8107 includes ARM® Cortex™-A8: SVCT/H.264/MJPEG video coprocessor: Gigabit EMAC: PCIe for BOM savingsHardware:Multi-storage of compressed input (SATA x2 to x8 with support for DVD backup through eSATA port) and PCI ExpressStreaming of compressed input (Gigabit Ethernet)Local display support HDMI monitor: VGA monitor and a spot monitorLocal user interface support Frame Buffer graphicsPan: tilt and zoom camera supportSoftware:Multi-codec system allows triple stream per channel (SVCT/H.264 and MJPEG) for real-time signal processingSimultaneous record (480 fps CIF Enc + 120 fps QCIF enc): playback (480 fps CIF dec): storage: streaming and displaySupports 4 Channel D1 DVR system (120fps D1 Enc + 120fps CIF Enc + 120 fps D1 Dec)NVR decode and display up to 120 megapixels of video per second: which is equivalent to 360 fps D1 or 60 fps full HD (1080p / 2 megapixel) videoAudio/video adjustment and search toolsVideo timestamp supportSoftware Development Kit (SDK) provided for easy customization

This design provides a reference ZigBee® gateway for IoT lighting applications. Feature-rich: Linux-based Network & GUI applications powered by Sitara™ AM335x processor can control and monitor ZigBee lighting nodes using the SimpleLink™ ZigBee CC2531 wireless MCU. This design includes example applications for local and remote control of ZigBee nodes: including Android (phones/tablets/set top boxes): Java-script for cloud connectivity agents and C-clients.

The LT8602 is a quad channel, current mode, monolithic buck switching regulator with a programmable power-on reset. All regulators are synchronized to a single oscillator with an adjustable frequency from 250kHz to 2.2MHz. The LT8602 can be configured for micropower Burst Mode operation or pulse-skipping operation at light load. Micropower operation results in quiescent current of 30?A with all four regulators operating in the application below.The high voltage channels are synchronous buck regulators that operate from an input of 3V to 42V. The output currents are up to 1.5A (OUT1) and 2.5A (OUT2). The low voltage channels operate from an input of 2.6V to 5.5V. Internal synchronous power switches provide high efficiency with output currents up to 1.8A. The LT8602 uses a 2-phase clock with channels 1 and 3 operating 180? from channels 2 and 4 to reduce input ripple current on both HV and LV inputs. All channels have cycle-by-cycle current limit, providing protection against shorted outputs. Thermal shutdown provides additional protectionThe LT8602 is available in either a 40-lead 6mm ? 6mm QFN or a 48-Lead 7mm ? 7mm LQFP package.APPLICATIONS Automotive Systems Distributed Supply Regulation Industrial Controls and Power Supplies

This design presents a low-cost: small size: robust 200-VA DC to AC inverter based on TI’s MSP430 and UCD8220-digitally managed push-pull controller. It is targetted towards car inverters and small-segment inverters for commercial applications. In this design: UCD8220 is used for a boost stage to get 250-V DC from a 12-V battery. The MSP430 acts as a host controller and provides a 100-kHz clock to UCD8220 and drives for output DC-AC bridge. This inverter has a peak efficiency of 90% and has natural cooling and does not require a fan for cooling.

The AD8479 is a difference amplifier with a very high inputcommon-mode voltage range. The AD8479 is a precision devicethat allows the user to accurately measure differential signals inthe presence of high common-mode voltages up to ?600 V.The AD8479 can replace costly isolation amplifiers in applicationsthat do not require galvanic isolation. The device operates overa ?600 V common-mode voltage range and has inputs that areprotected from common-mode or differential mode transientsup to ?600 V.The AD8479 has low offset voltage, low offset voltage drift, low gain drift, low common-mode rejection drift, and excellent common-mode rejection ratio (CMRR) over a wide frequency range.The AD8479 is available in a space-saving 8-lead SOIC package and is operational over the ?40?C to +125?C temperature range.Applications High voltage current sensing Battery cell voltage monitors Power supply current monitors Motor controls Isolation

This reference design provides 12V at 10A from a wide range 18V-60V telecom input with greater than 93% efficiency. This design uses the UCC2897A active clamp controller with synchronous rectifiers for an efficient: yet cost effective solution that can operate from either a 24VDC or 48VDC input bus.

The AD9520-5 provides a multioutput clock distributionfunction with subpicosecond jitter performance, along withan on-chip PLL that can be used with an external VCO.The AD9520-5 serial interface supports both SPI and I2C ports.An in-package EEPROM, which can be programmed through theserial interface, can store user-defined register settings forpower-up and chip reset.The AD9520-5 features 12 LVPECL outputs in four groups. Anyof the 1.6 GHz LVPECL outputs can be reconfigured as two250 MHz CMOS outputs. If an application requires LVDSdrivers instead of LVPECL drivers, refer to the AD9522-5.Each group of three outputs has a divider that allows both thedivide ratio (from 1 to 32) and the phase offset or coarse timedelay to be set.The AD9520-5 is available in a 64-lead LFCSP and can be operatedfrom a single 3.3 V supply. The external VCO can have anoperating voltage of up to 5.5 V. A separate output driver powersupply can be from 2.375 V to 3.465 V.The AD9520-5 is specified for operation over the standardindustrial range of ?40?C to +85?C. Applications Low jitter, low phase noise clock distribution Clock generation and translation for SONET, 10Ge, 10GFC, Synchronous Ethernet, OTU2/3/4 Forward error correction (G.710) Clocking high speed ADCs, DACs, DDSs, DDCs, DUCs, MxFEs High performance wireless transceivers ATE and high performance instrumentation Broadband infrastructures

This TI Precision Verified Design provides the theory: component selection: simulation: complete PCB schematic and layout: bill of materials: and measured performance of a split-supply: high-side four decade current sensing solution that can accurately detect load currents from 10uA-100mA. The corresponding linear output is from 10mV to 4.9V which enables measurement by common 5V ADCs. The design utilizes the PGA281: an instrumentation amplifier with pin-programmable gain and a wide common-mode voltage range: to provide a more accurate and versatile solution than traditional op amps.See more TI Precision Designs

AN-726 Station Management Simplified

This demonstration board is desinged for 5W / 3 LEDs MR16 application. The board is favorable for difference supply source: DC power supply (12VDC): AC Magnet Transfomer (12VAC with 50/60Hz) & E-transfromer (12VAC). Also: It has very good E-transfomer compatability and higher efficiency.

DC1625A-A: Demo Board for the LTC4227 Dual Ideal Diode and Single Hot Swap Controller.

DC816A-G: Demo Board for the LTC2298 Dual 14-Bit, 65Msps Low Power 3V ADCs.