Search results
Search the entire Electronics Datasheets database for parts, reference designs, application notes and evaluation kits.
CT203M
onsemi
Temperature Sensor Digital, Local 8-DFN (2x2)
| Distributor | SKU | Stock | MOQ | 1 | 10 | 50 | 100 | 1,000 | 10,000 | |
|---|---|---|---|---|---|---|---|---|---|---|
| DigiKey | 2156-NCT203MTR2G-488-ND | 168,000 | 168 | $1.49 | $1.49 | Buy |
Adding Hysteresis to Low-Battery Input on the TPS6211x
Texas Instruments
Adding Hysteresis to Low-Battery Input on the TPS6211x
Texas Instruments
The low-battery input (LBI) available on several step-down converters is often used to shut down the converter when the input voltage falls below a set threshold. This prevents damage to the battery and signals that the battery is at the end of its life and must be charged or replaced. Batteries have internal resistance that causes the voltage to drop as the load increases. This internal resista
DN102 -- SoC Temperature Sensor (Rev. A)
Texas Instruments
DN102 -- SoC Temperature Sensor (Rev. A)
Texas Instruments
This design note includes descriptions and a code example for easily measuring the temperature of a device by using the internal temperature sensor connected to the ADC. The code is suitable for the CC1110 CC1111 CC2430 CC2431 CC2510 and CC2511 system on chip (SOC) devices.
Three-Phase Brushless DC Motor Driver
Texas Instruments
Three-Phase Brushless DC Motor Driver
Texas Instruments
The Three-Phase Brushless DC Motor Driver reference design is a 10A: 3-phase brushless DC drive stage based on the DRV8301 pre-driver and CSD18533Q5A NextFET™ power MOSFET. It has three low side current sense amps (two internal to DRV8301: one external). The design also leverages a 1.5A step down buck converter: is fully protected with short circuit: thermal: and shoot-through protection: and is easily configured via a SPI interface. It is ideal for sensorless: brushless control techniques and drive stage design.
300VDCin to 600VDCin; 20Vout @ 1.5A Reference Design
Texas Instruments
300VDCin to 600VDCin; 20Vout @ 1.5A Reference Design
Texas Instruments
A high voltage input isolated flyback converter that accepts an input voltage of 300VDCin to 600VDCin and provides an isolated output of 20Vout capable of supplying 1.5A.
7 to 12Vin 1.2Vout 8A Step-down Conv for Powering Rails in Altera Arria V FPGA Reference Design
Texas Instruments
7 to 12Vin 1.2Vout 8A Step-down Conv for Powering Rails in Altera Arria V FPGA Reference Design
Texas Instruments
The PMP8824 uses the TPS53318 DCAP Mode 8A step-down converter to power the VCCR_GXB: VCCL_GXB: VCCT_GXB rails in Altera Arria® V FPGAs enabling tight load regulation: low total component count: high efficiency: high power density: and excellent thermal performance. The complete design fits in 0.29 square inches and comes with a complete test report including power up and ENABLE into Short Circuit: Over-Current Thermal Stress: and demonstration of the Redundant OVP feature when the Feedback Node is shorted to GND.
Fully Integrated Switchmode One-Cell Li-Ion Charger w/Full USB Compl & USB-OTG Reference Design
Texas Instruments
Fully Integrated Switchmode One-Cell Li-Ion Charger w/Full USB Compl & USB-OTG Reference Design
Texas Instruments
This reference design is a complete charger module for evaluating compact: flexible: high-efficiency: USB-friendly switch-mode charge management solutions for single-cell Li-ion and Li-polymer batteries used in a wide range of portable applications. It integrates a synchronous PWM controller: power MOSFETs: input current sensing: high-accuracy current and voltage regulation: and charge termination: into a small WCSP package. The charge parameters can be programmed through an I²C interface.