Search results

This application report discusses the process of replacing the CLC016 reclocker with the LMH0026 reclocker.

The Texas Instruments bq27411-G1 reference design is an easy to configure fuel gauging solution for single series cell Li-Ion battery packs. The device requires minimal configuration and uses One Time Programmable (OTP) Non-Volatile Memory (NVM) to avoid an initialization download by the system processor.The bq27411-G1 uses the patented Impedance Track™ algorithm for fuel gauging: and provides information such as remaining battery capacity (mAh): state-of-charge (%): and battery voltage (mV).

The ADATE209 is a dual pin driver designed for testing DDR2, DDR3, and DDR4. It can also be used for high speed SoC applications, such as testing PCI Express 1.0 and HDMI?. The device is a three-level driver capable of high fidelity swings from 200 mV to 4 V over a ?1 V to +3.5 V range. It has rise/fall times (20% to 80%) under 120 ps for a 2 V programmed swing and 150 ps for a 3 V programmed swing, and is capable of supporting data rates of 4.4 Gbps and 3.2 Gbps, respectively.The device is capable of high speed transitions into and out of termination mode. It also contains peaking/pre-emphasis circuitry.The ADATE209 is available in an 8 mm ? 8 mm, 49-ball CSP_BGA.APPLICATIONS Automatic test equipment Semiconductor test systems Board test systems Instrumentation and characterization equipment High speed memory testing (DDR2/DDR3/DDR4) HDMI testing

This design uses a synchronous buck converter to provide light load efficiency with predictable ripple off Telecom" voltage range. This approach is described in the TPS54061 datasheet from page 23 onwards. A low fixed frequency of 50kHz with operation in the discontinuous mode at all: but the highest loading achieves excellent efficiency at light loads without the "burst mode" which creates unpredicable ripple. PMP9535 extends operation into the 36-57V input range: and demonstates stability at 150mA load where conduction becomes continuous."

Demonstration circuit 1447A is an adjustable 200mA linear regulator featuring LT3082. Architected as a precision current source and voltage follower, it allows this new regulator to be used in many applications with adjustability to zero output. The LT3082 has an input range of 1.2V to 40V, but the demo board limits this range to 2.8V to 35V. The LT3082 withstands reverse input voltages and reverse output-to-input voltages without reverse-current flow.

The TIDA-00133 reference design is a high speed serial video interface to connect a remote automotive camera module to a display or machine vision processing system. It uses TIs FPD-Link III SerDes technology to transmit uncompressed MegaPixel video data: bidirectional control signals and power either over shielded twisted pair or coax cable. This design incorporates the DS90UB913A-CXEVM and DS90UB914A-CXEVM boards together to create the solution.

Spartan™-3 Design 1 - TPS64203 Switching DC/DC Controller-Based Power Management Solution Providing up to 3 A from VIN = 5.0 V or 3.3 V.

The ADL8107 is a gallium arsenide (GaAs), monolithic microwave IC (MMIC), pseudomorphic high electron mobility transistor (pHEMT), low noise, wideband, high linearity amplifier that operates from 6 GHz to 18 GHz.The ADL8107 provides a typical gain of 24 dB at 7 GHz to 16 GHz, a 1.3 dB typical noise figure at 7 GHz to 16 GHz, a 18.5 dBm typical output power for 1 dB compression (OP1dB) at 7 GHz to 16 GHz, and a typical output third-order intercept (OIP3) of 29 dBm at 7 GHz to 16 GHz, requiring only 90 mA from a 5 V drain supply voltage. This low noise amplifier has a high output second-order intercept (OIP2) of 30.5 dBm typical at 7 GHz to 16 GHz, making the ADL8107 suitable for military and test instrumentation applications.The ADL8107 also features inputs and outputs that are internally matched to 50 ?. The RFIN and RFOUT pins are internally ac-coupled, and the bias inductor is also integrated, making the ADL8107 ideal for surface-mounted technology (SMT)-based, high density applications.The ADL8107 is housed in a RoHS-compliant, 2 mm ? 2 mm, 8-lead LFCSP.APPLICATIONSTest instrumentationMilitary communicationsRadar

This application note presents a simple scheme to improve the drop-out voltage in constant-on-time buckregulators.

DC2985A is a multi-output power management solution demonstration circuit, featuring the LT3380. It contains two 2.5A, two 1.5A synchronous step-down DC/DC regulators and three 300mA LDO regulators. All regulators can be enabled with external enable pins. After the first regulator is enabled, the remaining enable pins use a precision threshold to allow hardwire-programmed Power-Up Sequence. A micro-USB communication interface is integrated on board to allow software GUI to write or read the registers in LT3380 via its I2C serial port. This GUI can control regulator enables, power-down sequencing, output voltage levels, dynamic voltage scaling, operation modes, status reporting and other special functions. Refer to LT3380 data sheet for more details on the electrical specifications and the setting of its command registers.

LB-19 Predicting OP Amp Slew Rate Limited Response

This reference design is synchronous buck-boost converter that can deliver up to 3.8 A of continuous current at -5 V from a 5 V input. This topology uses a synchronous buck controller (TPS5103) referenced to the negative output rail. The synchronous MOSFETs allow this design to achieve a peak eff

A coupled inductor non-synchronous boost converter that accepts an input voltage of 4.5Vin to 5.5Vin and provides an output of 80Vout capable of delivering 2mA. This design has a very high output-to-input voltage boost ratio.

This application report explains how use TI’s reliability de-rating tools to calculate a component level FIT under power on conditions for a system mission profile.

The AD5124/AD5144/AD5144A potentiometers provide a nonvolatile solution for 128-/256-position adjustment applications, offering guaranteed low resistor tolerance errors of ?8% and up to ?6 mA current density in the Ax, Bx, and Wx pins.The low resistor tolerance and low nominal temperature coefficientsimplify open-loop applications as well as applications requiringtolerance matching.The linear gain setting mode allows independent programmingof the resistance between the digital potentiometer terminals, through the RAW and RWB string resistors, allowing very accurate resistor matching.The high bandwidth and low total harmonic distortion (THD)ensure optimal performance for ac signals, making these devicessuitable for filter design.The low wiper resistance of only 40 ? at the ends of the resistor array allow for pin-to-pin connection.The wiper values can be set through an SPI-/I2C-compatible digital interface that is also used to read back the wiper register andEEPROM contents.The AD5124/AD5144/AD5144A are available in a compact, 24-lead, 4 mm ? 4 mm LFCSP and a 20-lead TSSOP. The partsare guaranteed to operate over the extended industrial temperaturerange of ?40?C to +125?C.APPLICATIONS Portable electronics level adjustment LCD panel brightness and contrast controls Programmable filters, delays, and time constants Programmable power suppliesThe AD5144-EP supports defense and aerospace applications (AQEC).

DRV8711 DRV8711 Quick Spin and Tuning Guide