Search results for: ADUM5200ARWZ-RL

The ADuM520x are dual channel digital isolators with isoPower, an integrated, isolated dc-to-dc converter. Based onthe Analog Devices, Inc., iCoupler® technology, the dc-to-dcconverter provides up to 500 mW of regulated, isolated powerwith 5.0 V input and 5.0 V output voltage, or 200 mW of power with 3.3 V input and 3.3 V output voltage. This eliminates the need for a separate isolated dc-to-dc converter in low power isolated designs. The Analog Devices chip scale transformer iCoupler technology is used for the isolation of the logic signals as well as for the dc-to-dc converter. The result is a small form factor, total isolation solution.ADuM520x units may be used in combination with ADuM5401, ADuM5402, ADuM5403, ADuM5404 and ADuM5000 with isoPower® to achieve higher output power levels and greater channel counts (see the Increasing Available Power section).The ADuM520x isolators provide two independent isolationchannels in a variety of channel configurations and data rates(see the Ordering Guide for options).isoPower uses high frequency switching elements to transfer power through its transformer. Special care must be taken during printed circuit board (PCB) layout to meet emissionsstandards. Refer to the AN-0971 application note for details on board layout recommendations.APPLICATIONS RS-232/RS-422/RS-485 transceiver Industrial field bus isolation Power supply startups and gate drives Isolated sensor interfaces Industrial PLCs

General Purpose Digital Isolator 2500Vrms 2 Channel 1Mbps 25kV/µs CMTI 16-SOIC (0.295", 7.50mm Width)

Dual-Channel Isolators with Integrated DC-to-DC Converter(0/2 channel directionality) Features: For AEC-Q100 Automotive Qualified Devices Specifications - Please View ADuM520xW Datasheet. isoPower® integrated isolated DC/DC converter Regulated 3V or 5V output Up to 500 mW output power Dual dc-to-25 Mbps (NRZ) signal isolation channels Schmitt Trigger Inputs 16-lead SOIC package with >8 mm creepage High temperature operation: 105°C maximum High common-mode transient immunity: > 25 kV/µs Safety and regulatory approvals UL recognition 2500 V rms for 1 minute per UL 1577 CSA component accept notice #5A (pending) VDE cert of conformity (pending) DIN V VDE V 0884-10 (VDE V 0884-10): 2006-12 VIORM = 560 VPEAK

The ADuM5230 is an isolated half-bridge gate driver thatemploys Analog Devices, Inc., iCoupler® technology to provideindependent and isolated high-side and low-side outputs.Combining CMOS and microtransformer technologies, thisisolation component contains an integrated dc-to-dc converterproviding an isolated high-side supply. This eliminates the cost,space, and performance difficulties associated with externalsupply configurations such as bootstrap circuitry. This highsideisolated supply powers not only the ADuM5230 high-sideoutput but also any external buffer circuitry used with theADuM5230.In comparison to gate drivers employing high voltage leveltranslation methodologies, the ADuM5230 offers the benefitof true, galvanic isolation between the input and each output.Each output can operate up to ±700 VP relative to the input,thereby supporting low-side switching to negative voltages.The differential voltage between the high side and low sidemay be as high as 700 VP.Applications MOSFET/IGBT gate drives Automotive Motor drives Power supplies

Quad-Channel Isolator with Integrated DC-to-DC Converter (4/0 channel directionality) Features: isoPower integrated, isolated dc-to-dc converter Regulated 5 V output 500 mW output power Quad dc-to-25 Mbps (NRZ) signal isolation channels Schmitt trigger inputs 16-lead SOIC package with >8 mm creepage High temperature operation: 105°C See Data Sheet for Additional Information

The ADuM2200 / ADuM2201 are 2-channel digital isolators based on Analog Devices, Inc., iCoupler® technology. Combining high speed CMOS and monolithic air core transformer technology, these isolation components provide outstanding performance characteristics that are superior to alternatives such as optocoupler devices.By avoiding the use of LEDs and photodiodes, iCoupler devices remove the design difficulties commonly associated with optocouplers. Typical optocoupler concerns regarding uncertain current transfer ratios, nonlinear transfer functions, and temperature and lifetime effects are eliminated with the simple iCoupler digital interfaces and stable performance characteristics. The need for external drivers and other discrete components is eliminated with these iCoupler products. Furthermore, iCoupler devices consume one-tenth to one-sixth the power of optocouplers at comparable signal data rates.The ADuM2200 / ADuM2201 isolators provide two independent isolation channels in two channel configurations with data rates up to 10 Mbps (see the Ordering Guide). Both parts operate with the supply voltage on either side ranging from 3.0 V to 5.5 V, providing compatibility with lower voltage systems, as well as enabling voltage translation functionality across the isolation barrier. The ADuM2200 / ADuM2201 isolators have a patented refresh feature that ensures dc correctness in the absence of input logic transitions and during power-up/power-down conditions.Similar to the ADuM3200 / ADuM3201 isolators, the ADuM2200 / ADuM2201 isolators contain various circuit and layout enhancements that provide increased capability relative to system-level IEC 61000-4-x testing (ESD, burst, and surge). The precise capability in these tests for either the ADuM3200 / ADuM3201 or ADuM2200 / ADuM2201 products is strongly determined by the design and layout of the user’s board or module. For more information, see the AN-793 Application Note, ESD/Latch-Up Considerations with iCoupler Isolation Products.APPLICATIONS General-purpose, high voltage, multichannel isolation Medical equipment Power supplies RS-232/RS-422/RS-485 transceiver isolation Hybrid electric vehicles, battery monitors, and motor drives

The ADuM5000 is an isolated DC/DC converter based on the Analog Devices, Inc., iCoupler® technology. The DC/DC converter in this device provides regulated, isolated power in several combinations of input and output voltage as listed in Table 1.The Analog Devices chip-scale transformer iCoupler technology transfers isolated power in this DC/DC converter with up to 33% efficiency. The result is a small form factor, total isolationsolution.Higher output power levels are obtained by using the ADuM5000 to augment the power output of ADuM5401, ADuM5402, ADuM5403, ADuM5404, and ADuM520x iCouplers with isoPower®.isoPower uses high frequency switching elements to transfer power through its transformer. Special care must be taken during printed circuit board (PCB) layout to meet emissionsstandards. Refer to the AN-0971 application note for board layout recommendations.APPLICATIONS RS-232/RS-422/RS-485 transceivers Industrial field bus isolation Power supply start ups and gate drives Isolated sensor interface Industrial PLCs

The ADuM520x are dual channel digital isolators with isoPower, an integrated, isolated dc-to-dc converter. Based onthe Analog Devices, Inc., iCoupler® technology, the dc-to-dcconverter provides up to 500 mW of regulated, isolated powerwith 5.0 V input and 5.0 V output voltage, or 200 mW of power with 3.3 V input and 3.3 V output voltage. This eliminates the need for a separate isolated dc-to-dc converter in low power isolated designs. The Analog Devices chip scale transformer iCoupler technology is used for the isolation of the logic signals as well as for the dc-to-dc converter. The result is a small form factor, total isolation solution.ADuM520x units may be used in combination with ADuM5401, ADuM5402, ADuM5403, ADuM5404 and ADuM5000 with isoPower® to achieve higher output power levels and greater channel counts (see the Increasing Available Power section).The ADuM520x isolators provide two independent isolationchannels in a variety of channel configurations and data rates(see the Ordering Guide for options).isoPower uses high frequency switching elements to transfer power through its transformer. Special care must be taken during printed circuit board (PCB) layout to meet emissionsstandards. Refer to the AN-0971 application note for details on board layout recommendations.APPLICATIONS RS-232/RS-422/RS-485 transceiver Industrial field bus isolation Power supply startups and gate drives Isolated sensor interfaces Industrial PLCs

ISOLATORS ROHS COMPLIANT: YES

Dual-Channel, 5 kV Isolators with Integrated DC/DC Converter (2/0 channel directionality) Features: isoPower integrated, isolated DC/DC converter Regulated 5 V or 3.3 V output Up to 400 mW output power 16-lead SOIC package with 7.6 mm creepage Dual dc-to-25 Mbps (NRZ) signal isolation channels High common-mode transient immunity: >25 kV/μs Safety and regulatory approvals UL recognition (pending) 5000 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice #5A IEC 60601-1: 125 V rms IEC 60950-1: 380 V rms VDE certificate of conformity (pending) IEC 60747-5-2 (VDE 0884 Part 2):2003-01 VIORM = 846 V peak High temperature operation: 105°C maximum

Dual-Channel Isolators with Integrated DC-to-DC Converter (2/0 channel directionality) Features: For AEC-Q100 Automotive Qualified Devices Specifications Please View ADuM520xW Datasheet. isoPower® integrated isolated DC/DC converter Regulated 3V or 5V output Up to 500 mW output power Dual dc-to-25 Mbps (NRZ) signal isolation channels Schmitt Trigger Inputs 16-lead SOIC package with >8 mm creepage High temperature operation: 105°C maximum High common-mode transient immunity: > 25 kV/µs Safety and regulatory approvals UL recognition 2500 V rms for 1 minute per UL 1577 CSA component accept notice #5A (pending) VDE cert of conformity (pending) DIN V VDE V 0884-10 (VDE V 0884-10): 2006-12 VIORM = 560 VPEAK

Dual-Channel, 5 kV Isolators with Integrated DC/DC Converter (2/0 channel directionality) Features: isoPower integrated, isolated DC/DC converter Regulated 5 V or 3.3 V output Up to 400 mW output power 16-lead SOIC package with 7.6 mm creepage Dual dc-to-25 Mbps (NRZ) signal isolation channels High common-mode transient immunity: >25 kV/μs Safety and regulatory approvals UL recognition (pending) 5000 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice #5A IEC 60601-1: 125 V rms IEC 60950-1: 380 V rms VDE certificate of conformity (pending) IEC 60747-5-2 (VDE 0884 Part 2):2003-01 VIORM = 846 V peak High temperature operation: 105°C maximum

The ADuM640x devices are quad-channel digital isolators with isoPower®, an integrated, isolated DC/DC converter. Based on the Analog Devices, Inc., iCoupler® technology, the DC/DC converter provides up to 500 mW of regulated, isolated power at either 5.0 V or 3.3 V from a 5.0 V input supply, or 3.3 V from a 3.3 V supply at the power levels shown in Table 1. This eliminates the need for a separate, isolated DC/DC converter in low power, isolated designs. The iCoupler chip scale transformer technology is used to isolate the logic signals and for the magnetic components of the DC/DC converter. The result is a small form factor, total isolation solution.The ADuM640x isolators provide four independent isolation channels in a variety of channel configurations and data rates (see the Ordering Guide for more information).isoPower uses high frequency switching elements to transfer power through its transformer. Special care must be taken during printed circuit board (PCB) layout to meet emissions standards. Refer to the AN-0971 application note for board layout recommendations at www.analog.com.

Quad-Channel, 2.5 kV Isolators with Integrated DC-to-DC Converter (1/3 channel directionality) Features: isoPower integrated, isolated dc-to-dc converter Regulated 3.3 V or 5.0 V output Up to 500 mW output power Quad dc-to-25 Mbps (NRZ) signal isolation channels 16-lead SOIC package with 7.6 mm creepage High temperature operation: 105°C maximum High common-mode transient immunity: >25 kV/μs Safety and regulatory approvals UL recognition 2500 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A VDE certificate of conformity IEC 60747-5-2 (VDE 0884, Part 2) VIORM = 560 V peak CQC certification per GB4943.1-2011

The ADuM3400/ADuM3401/ADuM3402 are 4-channel digitalisolators based on the Analog Devices, Inc., iCoupler® technology.Combining high speed CMOS and monolithic air coretransformer technology, these isolation components provideoutstanding performance characteristics superior to alternativessuch as optocoupler devices.iCoupler devices remove the design difficulties commonlyassociated with optocouplers. Typical optocoupler concernsregarding uncertain current transfer ratios, nonlinear transferfunctions, and temperature and lifetime effects are eliminatedwith the simple iCoupler digital interfaces and stable performancecharacteristics. The need for external drivers and other discretecomponents is eliminated with these iCoupler products. Furthermore,iCoupler devices consume one-tenth to one-sixth thepower of optocouplers at comparable signal data rates.The isolators provide four independent isolation channels in avariety of channel configurations and data rates (see theOrdering Guide). All models operate with the supply voltage oneither side ranging from 2.7 V to 5.5 V, providing compatibilitywith lower voltage systems as well as enabling a voltagetranslation functionality across the isolation barrier. Theisolators have a patented refresh feature that ensures dc correctnessin the absence of input logic transitions and during powerup/power-downconditions.In comparison to the ADuM1400/ADuM1401/ADuM1402isolators, the ADuM3400/ADuM3401/ADuM3402 isolatorscontain various circuit and layout changes to provide increasedcapability relative to system-level IEC 61000-4-x testing (ESD/burst/surge). The precise capability in these tests for either set ofisolators is strongly determined by the design and layout of theuser’s board or module. For more information, see the AN-793 application note, ESD/Latch-Up Considerations with iCoupler Isolation Products.Applications General-purpose multichannel isolation SPI/data converter isolation RS-232/RS-422/RS-485 transceivers Industrial field bus isolation

The ADuM2200 / ADuM2201 are 2-channel digital isolators based on Analog Devices, Inc., iCoupler® technology. Combining high speed CMOS and monolithic air core transformer technology, these isolation components provide outstanding performance characteristics that are superior to alternatives such as optocoupler devices.By avoiding the use of LEDs and photodiodes, iCoupler devices remove the design difficulties commonly associated with optocouplers. Typical optocoupler concerns regarding uncertain current transfer ratios, nonlinear transfer functions, and temperature and lifetime effects are eliminated with the simple iCoupler digital interfaces and stable performance characteristics. The need for external drivers and other discrete components is eliminated with these iCoupler products. Furthermore, iCoupler devices consume one-tenth to one-sixth the power of optocouplers at comparable signal data rates.The ADuM2200 / ADuM2201 isolators provide two independent isolation channels in two channel configurations with data rates up to 10 Mbps (see the Ordering Guide). Both parts operate with the supply voltage on either side ranging from 3.0 V to 5.5 V, providing compatibility with lower voltage systems, as well as enabling voltage translation functionality across the isolation barrier. The ADuM2200 / ADuM2201 isolators have a patented refresh feature that ensures dc correctness in the absence of input logic transitions and during power-up/power-down conditions.Similar to the ADuM3200 / ADuM3201 isolators, the ADuM2200 / ADuM2201 isolators contain various circuit and layout enhancements that provide increased capability relative to system-level IEC 61000-4-x testing (ESD, burst, and surge). The precise capability in these tests for either the ADuM3200 / ADuM3201 or ADuM2200 / ADuM2201 products is strongly determined by the design and layout of the user’s board or module. For more information, see the AN-793 Application Note, ESD/Latch-Up Considerations with iCoupler Isolation Products.APPLICATIONS General-purpose, high voltage, multichannel isolation Medical equipment Power supplies RS-232/RS-422/RS-485 transceiver isolation Hybrid electric vehicles, battery monitors, and motor drives

I2C Digital Isolator 5000Vrms 2 Channel 1Mbps 25kV/µs CMTI 16-SOIC (0.295", 7.50mm Width)

The ADuM5401 / ADuM5402 / ADuM5403 / ADuM5404 arequad-channel digital isolators with isoPower®, an integrated,isolated dc-to-dc converter. Based on the Analog Devices, Inc.,iCoupler® technology, the dc-to-dc converter provides up to 500 mW of regulated, isolated power at either 5.0 V or 3.3 Vfrom a 5.0 V input supply, or at 3.3 V from a 3.3 V supply at thepower levels shown in Table 1. These devices eliminate the need for a separate, isolated dc-to-dc converter in low power, isolated designs. The iCoupler chip scale transformer technology is used to isolate the logic signals and for the power and feedback pathsin the dc-to-dc converter. The result is a small form factor, total isolation solution.The ADuM5401 / ADuM5402 / ADuM5403 / ADuM5404 isolatorsprovide four independent isolation channels in a variety of channel configurations and data rates (see the Ordering Guidefor more information).isoPower uses high frequency switching elements to transfer power through its transformer. Special care must be taken during printed circuit board (PCB) layout to meet emissions standards. See the AN-0971 Application Note for board layout recommendations.APPLICATIONS RS-232/RS-422/RS-485 transceivers Industrial field bus isolation Power supply startup bias and gate drives Isolated sensor interfaces Industrial PLCs

The ADuM130x are triple-channel digital isolators based on the Analog Devices, Inc., iCoupler® technology. Combining high speed CMOS and monolithic transformer technology, these isolation components provide outstanding performance characteristics superior to alternatives, such as optocouplers.By avoiding the use of LEDs and photodiodes, iCoupler devices remove the design difficulties commonly associated with optocouplers. The typical optocoupler concerns regarding uncertain current transfer ratios, nonlinear transfer functions, and temperature and lifetime effects are eliminated with the simple iCoupler digital interfaces and stable performance characteristics. The need for external drivers and other discrete components is eliminated with these iCoupler products. Furthermore, iCoupler devices consume one-tenth to one-sixth of the power of optocouplers at comparable signal data rates.The ADuM130x isolators provide three independent isolation channels in a variety of channel configurations and data rates (see the Ordering Guide in the data sheet). Both models operate with the supply voltage on either side ranging from 2.7 V to 5.5 V, providing compatibility with lower voltage systems as well as enabling a voltage translation functionality across the isolation barrier. In addition, the ADuM130x provide low pulse width distortion (<2 ns for CRW grade) and tight channel-to-channel matching (<2 ns for CRW grade). Unlike other optocoupler alternatives, the ADuM130x isolators have a patented refresh feature that ensures dc correctness in the absence of input logic transitions and when power is not applied to one of the supplies.APPLICATIONS General-purpose multichannel isolation SPI interface/data converter isolation RS-232/RS-422/RS-485 transceivers Industrial field bus isolation Automotive systems

Digital Isolators Quad Channel Isolators w/Int DC/DC Conv