This application report describes a pressure sensor circuit suitable for use in underwater equipment or in altitude measurement devices. The circuit operates from a 3-V supply and does the analog-to-digital conversions for pressure and temperature measurements.

This document describes a test procedure used to validate that the Clarity Clear-Voice Capture Hands-Free Kit (CVC-HFK) software has been correctly installed and the hardware is functioning correctly.

This document defines the initialization process required for the TVP5145 Video Decoder. It discusses the strapping terminals the power up and reset requirements starting the microprocessor and initializing the internal registers.

LB-27 Micropower Thermometer

This application report describes the configuration changes in the data flash constants in the Texas Instruments bq20z40/45 and bq20z60/65 Gas Gauging Evaluation Software required for a variety of battery-pack configurations.

DCP0105, DCP0115, DCP0124, DCP01B, DCP02, DCR01/02, DCV01 External Synchronization of the DCP01/02, DCR01/02, and DCV01 Series of DC/DC Converters

The standard 12 V automotive battery rail can vary from 9 V-16 V during normal operation depending on load and charge. Under transients conditions battery voltages can range from 3 V to nearly 65 V. One of these extreme conditions is cold-crank. Cold-crank happens when the battery is trying to energize the starter of the engine and the battery voltage plummets to 3 V. Previousl

A limiter circuit consisting of an input buffer (A₁) an output-scaling amplifier (A₂) two zener diodes (Z₁ and Z₂) and several other components can supply sharp precise bipolar clamp levels with continuous variable control from 0 to ±11V. A feedback loop enclosing the amplifiers and zeners generates the high clamping accuracy.

AN-757 Measuring Ethernet Tap Capacitance

A standard has been established for daughtercards made to function with TMS320C6000™ and TMS320C5000™ systems. The daughtercard specification is based on the interfaces provided with several existing DSP motherboards: the TMS320C6201 EVM TMS320C6201 McEVM TMS320C6701 EVM TMS320C6211 DSK TMS320C6711 DSK TMS320C5402 DSK and TMS320C6202 EVM. The document is divided into two primary

This application report shows how to modify the bq24650 to charge a sealed, lead-acid battery from a solar panel. The circuit uses constant current (CC) charging to reach the bulk battery voltage and

The UCC3911 demonstration board comes fully assembled and ready to test. It provides complete overcharge/overdischarge protection, as well as short-circuit protection, for two lithium-ion cells. The

This application report presents guidelines for interfacing the Texas Instruments (TI(TM)) TLC5510 8-bit parallel-output analog-to-digital converter (ADC) to the TI TMS320C203 DSP data bus. The 8-bit ADC operates at a rate of 20 MHz. The C callable application program (assembly code) used to initialize the TMS320C203 and execute the code is also discussed.This report serves as reference inform

ControlNet Applications With the SN65HVD61 PHY

The TPS6211x high-input-voltage buck converters operate over a wide input-voltage range. The control and input signal can also be controlled from 1.8-V logic levels up to maximum input voltage.One characteristic of the EN and SYNC control circuits is the increase in leakage current when these pins are driven by a voltage level less than 4 V.In this application report the difference in th

This application report gives an overview on the currently defined DDR3 RDIMM RawCards by JEDEC. It is a summary of the register-relevant parameters of each RawCard Specification. Because JEDEC DDR3 standardization is still ongoing this report presents information available to date.

TPS54061, TPS54062 Using the TPS54061 to Create an Inverting Power Supply PMP/DC_Solutions/SWIFT/2-App_Reports/SLVA524

TRF3765 TRF3765 Output Terminations