<p>This document is a high-level starting point for those wanting to design USB devices with MSP430? MCUs. It provides an overview of the TI MSP430 hardware and software offerings for USB, as well as

TPS7B4250-Q1 Pin FMEA TPS7B4250-Q1

The CDCP1803 is a clock driver by design, but can be used as a data buffer. The CDCP1803 performance as a data buffer is demonstrated both in terms of the bit error rate (BER) and eye pattern diagram

This application report describes the procedure for placing Code Composer Studio? Integrated Development Environment (IDE) v2.0 under version control. With Code Composer Studio checked into a version control system developers can maintain a high degree of control over tools available for builds. The developer can now produce bit-exact versions of production code. This application report does not

Battery Charger Termination Issues With System Load Applied Across Battery While Charging

UCC2897A Peak Current Mode Active Clamp Forward Converter Small Signal Modeling Design Consideration written by Chinese engineer

One of the most predictable non-linear elements commonly available is the bipolar transistor. Therelationship between collector current and emitter base voltage is precisely logarithmic from currentsbelow one picoamp to currents above one milliamp. Using a matched pair of transistors and integratedcircuit operational amplifiers it is relatively easy to construct a linear to logarithmic conv

This document introduces a general formula to translate the phase noise of a clock source rated via the Single Sideband to Carrier Ratio to the cycle-to-cycle jitter of the oscillation period. The link allows to seamlessly aggregate the external clock source phase noise usually given in dBc/Hz to the phase stability figure of the on-chip clock synchronization circuitry usually rated in ps-RMS

This application report provides a reference design for Power over Ethernet (PoE) on the Power Device (PD) side using Texas Instruments LM5070 and the physical layer device DP83865 Gig PHYTER™

In telecommunications and signal processing, frequency modulation (FM) is encoding of information on a carrier wave by varying the instantaneous frequency of the wave. Digital data can be encoded and transmitted via carrier wave by shifting the carrier's frequency among a predefined set of frequencies—a technique known as frequency-shift keying (FSK). FSK is widely used in modems, radio-teletype and fax modems, and can also be used to send Morse code.

Frequency-shift keying (FSK) is a frequency modulation scheme in which digital information is transmitted through discrete frequency changes of a carrier wave. This application report discusses logiclevel implementation of binary FSK (BFSK) modulator and demodulator using a phase-locked loop PLL device – CD54HC4046A, CD54HCT4046A, CD74HC4046A, and CD74HCT4046A (hereafter in this document referred to as HC/HCT4046A). BFSK is the simplest FSK, using a pair of discrete frequencies to transmit binary information.

LB-25 True rms Detector

AN025 -- CC1020 RF MODEM

Appendix E: Understanding Integrated Circuit Package Power Capabilities

This application report provides information on the DM648/7 throughput performance and describes the DM648/7 System-on-Chip (SoC) architecture data path infrastructure and constraints that affect the throughput and different optimization techniques for optimum system performance. This document also provides information on the maximum possible throughput performance of different peripherals on th

UCC2891 Active Clamp Transformer Reset: High Side or Low Side?

DN019 -- Powering Low-Power RF Products

The synchronous buck converter controllers (TPS56100, TPS56300, TPS56xx, and TPS5602) made by Texas Instruments are specifically designed to provide excellent transient response and high efficienty to

This document assists in the estimation of power consumption for the TMS320C5510 digital signal processor (DSP). As power consumption can vary widely on this device a spreadsheet was developed to provide a better estimate. This allows the user to tailor the prediction to their particular application. It also allows designers the ability to test the efficiency of different configurations before an

The input offset voltage, VIO, is a common dc parameter in operational amplifier (op amp) specifications. This report aims to familiarize the engineer by discussing the basics and modern aspects of VI

This report presents a method for interfacing the ADS7822 12-bit SAR analog-to-digital converter to the TMS320C5402 DSP.