30 MHz TO 2 GHz Quadrature Demodulator Features: Operating RF frequency 30 MHz to 2 GHz Voltage conversion gain > 4 dB 60 MHz to 4 GHz Input IP3: 31 dBm @ 900 MHz Input IP2: 62 dBm @ 900 MHz Input P1dB: 13 dBm @ 900 MHz Noise figure (NF) 12.0 dB @ 140 MHz 14.7 dB @ 900 MHzLO input at 2 × fLO Quadrature demodulation accuracy Phase accuracy ~0.4° Amplitude balance ~0.05 dB Demodulation bandwidth ~240 MHz Baseband I/Q drive 2 Vp-p into 200 Ω Single 5 V supply

ADM1060 - Communication System Supervisory/Sequencing Circuit

ADM1811 - Microprocessor RESET Circuit

ADM1811 - Microprocessor RESET Circuit

ADM1812 - Microprocessor RESET Circuit

ADM1815 - Microprocessor Supervisor

ADM1817 - Microprocessor RESET Circuit

12-Bit, 170 MSPS/210 MSPS/250 MSPS, 1.8 V Analog-to-Digital Converter Features: SNR = 64.8 dBFS @ fIN up to 70 MHz @ 250 MSPS ENOB of 10.5 @ fIN up to 70 MHz @ 250 MSPS (−1.0 dBFS) SFDR = 80 dBc @ fIN up to 70 MHz @ 250 MSPS (−1.0 dBFS) Excellent Linearity DNL = ±0.3 LSB typical INL = ±0.7 LSB typical CMOS outputs Single data port at up to 250 MHz Interleaved dual port @ 1/2 sample rate up to 125 MHz 700 MHz full power analog bandwidth On-chip reference, no external decoupling required Integrated input buffer and track-and-hold Low power dissipation 272 mW @ 170 MSPS 364 mW @ 250 MSPS Programmable input voltage range 1.0 V to 1.5 V, 1.25 V nominal 1.8 V analog and digital supply operation Selectable output data format (offset binary, twos complement, Gray code)

10-Bit, Complete, 40 MSPS, dual Transmit D/A Converter Features: Complete 10-Bit, 40 MSPS Dual Transmit DAC Excellent Gain and Offset Matching Differential Nonlinearity Error: 0.5 LSB Effective Number of Bits: 9.5 Signal-to-Noise and Distortion Ratio: 59 dB Spurious-Free Dynamic Range: 71 dB 2x Interpolation Filters See datasheet for additional features

AD9823 - CORRELATED DOUBLE SampleR (CDS)

AD9848 - CCD Signal Processor with Integrated Timing Driver

AD9876 - Broadband Modem Mixed-Signal Front-End

Complete 10-Bit, 25 MHz CCD Signal Processor Features: 25 MSPS Correlated Double Sampler (CDS) 6 dB to 40 dB 10-Bit Variable Gain Amplifier (VGA) Low Noise Optical Black Clamp Circuit Preblanking Function 10-Bit, 25 MSPS A/D Converter No Missing Codes Guaranteed 3-Wire Serial Digital Interface 3 V Single-Supply Operation Space-Saving 32-Lead  5 mm 5 mm LFCSP Package

12-Bit CCD Signal Processor with Precision Timing Core Features: Correlated Double Sampler (CDS) 0 dB to 18 dB Pixel Gain Amplifier (PxGA®) 6 dB to 42 dB 10-Bit Variable Gain Amplifier (VGA) 12-Bit 36 MSPS A/D Converter Complete On-Chip Timing Driver Black Level Clamp with Variable Level Control Precision Timing Core with  <600 ps Resolution On-Chip 3 V Horizontal and RG Drivers 40-Lead LFCSP Package

Dual, Low Noise, Single-Supply Variable Gain Amplifier Features:2 independent linear-in-dB channels Input noise at maximum gain: 1.8 nV/Hz, 2.7 pA/Hz Bandwidth: 40 MHz (3 dB) Differential input Absolute gain range programmable 14 dB to +34 dB (FBK shorted to OUT) through Variable gain scaling: 20 dB/V through 40 dB/V Stable gain with temperature and supply variations Single-ended unipolar gain control Output common mode independently set Power shutdown at lower end of gain control Single 5 V supply Low power: 90 mW/channel

ADD8706 - 16V 5 + 1-Channel Operational Amplifier

Buck, SEPIC Switching Regulator IC Positive Adjustable 2.42V 1 Output 4.5A (Switch) TO-263-8, D²Pak (7 Leads + Tab), TO-263CA

2-Channel, 1 MSPS, Ultralow Power, 12-Bit ADC in 16-Lead TSSOP Features: Ultralow system power Flexible power/throughput rate management High performance 1 MSPS throughput with no latency/pipeline delay SNR: 70 dB typical at 10 kHz input frequency THD: −80 dB typical at 10 kHz input frequency INL: ±0.7 LSB typical, ±1.0 LSB maximum Small system footprint On-chip accurate 2.5 V reference, 5 ppm/°C typical drift MUXOUT/ADCIN to allow single buffer amplifier Daisy-chain mode 16-lead, 20-lead, and 24-lead 4 mm × 4 mm LFCSP packages See data sheet for additional features.

Ultralow Power, 1.8 V, 3 mm 3 mm, 2-Channel Capacitance Converter Features:Ultralow powerPower supply voltage: 1.8 V to 3.6 VOperation power supply current: 70 A typicalPower-down current: 2 A typicalFast response timeConversion time: 10 ms per channelWake-up time from serial interface: 300 sAdaptive environmental compensation2 capacitance input channelsSensor capacitance (CSENS): 0 pF up to 13 pFSensitivity up to 3 fF2 modes of operationStandalone with fixed settingsInterfaced to a microcontroller for user-defined settings2 detection output flags2-wire serial interface (I2C-compatible)Operating temperature: 40C to +85C10-lead LFCSP package (3 mm 3 mm 0.8 mm)

Low Cost, Low Power, True RMS-to-DC Converter Features: Converts an ac voltage waveform to a dc voltage and then converts to the true rms, average rectified, or absolute value 200 mV rms full-scale input range (larger inputs with input attenuator) High input impedance: 1012 Ω  Low input bias current: 25 pA maximum High accuracy: ±0.3 mV ± 0.3% of reading RMS conversion with signal crest factors up to 5 Wide power supply range: +2.8 V, −3.2 V to ±16.5 V Low power: 200 μA maximum supply current Buffered voltage output No external trims needed for specified accuracy Related device: the AD737 features a power-down control with standby current of only 25 μA; the dc output voltage is negative and the output impedance is 8 kΩ