Ultralow Distortion Current Feedback Differential ADC Driver Features: Extremely low harmonic distortion −105 dBc HD2 at 10 MHz −91 dBc HD2 at 70 MHz −87 dBc HD2 at 100 MHz −103 dBc HD3 at 10 MHz −98 dBc HD3 at 70 MHz −89 dBc HD3 at 100 MHz Better distortion at higher gains than VF amplifiers Low input voltage noise: 1.4 nV/√Hz High speed −3 dB bandwidth of 2.3 GHz 0.1 dB gain flatness: 150 MHz Slew rate: 5000 V/µs, 25% to 75% Fast 0.1% settling time: 10 ns Low input offset voltage: 0.3 mV typical Externally adjustable gain Stability and bandwidth controlled by feedback resistor See data sheet for additional features

5 GHz, Low Distortion ADC Driver/Line Driver Features: −3 dB bandwidth of 5 GHz (AV = 6 dB) Single resistor programmable gain: 0 dB to 18 dB Differential or single-ended input to differential output Low harmonic distortion (HD2/HD3 @ AV = 6 dB) −88/−69 dBc @ 250 MHz −77/−66 dBc @ 500 MHz −73/−72 dBc @ 1 GHz IMD3 @ 1 GHz = −63 dBc Slew rate 8700 V/μs (AV = 6 dB, 2 V step) 6600 V/μs (AV = 18 dB, 2 V step) Fast settling: 1 ns to 1%, 1.4 ns to 0.1% Fast overdrive recovery: 6.7 ns to 1%, 9.3 ns to 0.5% Single-supply operation: 5 V 0.1 dB gain flatness to 300 MHz DC level translation Available in 16-lead LFCSP

Radar Receive Path AFE: 4-Channel LNA and PGA Features: 4 channels of low noise amplifiers (LNA) followed by programmable gain amplifiers (PGA) Minimum −3 dB bandwidth of 5 MHz Typical –3 dB bandwidth of 42.3 MHz Typical slew rate of 28 V/µs Differential input and output Gain of 18 dB to 36 dB in 6 dB steps Selectable low noise and low power modes Input referred noise of 4.5 nV/√Hz at 18.3 mW per channel Input referred noise of 3.6 nV/√Hz at 34.8 mW per channel Input referred noise of 3.4 nV/√Hz at 54.8 mW per channel Qualified for automotive applications See data sheet for additional features

18-Bit, 15 MSPS, Module Data Acquisition Solution Features: Integrated fully differential ADC driver with signal scaling Wide input common-mode voltage range High common-mode rejection Single-ended to differential conversion Pin selectable input range with overrange Input ranges with 4.096 V REFBUF: ±10 V, ±5 V, ±4.096 V, ±2.5 V, and ±1.5 V Gain/attenuation options: 0.37, 0.73, 0.87, 1.38, and 2.25 Critical passive components 0.005% precision matched resistor array for FDA 9 mm × 9 mm, 0.8 mm pitch, 100-ball CSP_BGA package 2.5× footprint reduction vs. discrete solution Low power, dynamic power scaling, power-down mode 143 mW typical at 15 MSPS Throughput: 15 MSPS, no pipeline delay INL error: ±3.1 ppm typical, ±6.2 ppm maximum (Gain = 0.73, gain = 0.87, gain = 1.38, gain = 2.25) SINAD: 90.4 dB typical at 20 kHz (gain = 0.73) THD: −117 dB at 1 kHz, −110 dB at 100 kHz (gain = 0.73) Gain error: ±0.005%FS typical Gain error drift: ±0.13 ppm/°C typical On-board reference buffer with VCMO generation Serial LVDS interface Wide operating temperature range: −40°C to +85°C

16-Bit, 2 MSPS, Module Data Acquisition Solution Features: Improved design journey Fully differential ADC driver with selectable input range Input ranges with 5 V VREF: ±10 V, ±5 V, or ±2.5 V Essential passive components included ±0.005% iPassives matched resistor array Wide input common-mode voltage range High common-mode rejection ratio Single-ended to differential conversion Increased signal chain density Small, 7 mm × 7 mm, 0.80 mm pitch, 49-ball CSP_BGA 4× footprint reduction vs. discrete solution On-board reference buffer with VCM generation High performance Throughput: 2 MSPS, no pipeline delay Guaranteed 16-bit no missing codes INL: ±4.6 ppm typical, ±11.9 ppm guaranteed SINAD: 95 dB typical (G = 0.454) Offset error drift: 0.7 ppm/°C typical (G = 0.454) Gain error drift: ±0.5 ppm/°C typical Low total power dissipation: 51.6 mW typical at 2 MSPS SPI-/QSPI™ -/MICROWIRE™ -/DSP-compatible serial interface Versatile logic interface supply with 1.8 V, 2.5 V, 3 V, or 5 V

15 Lead ECG Vital Signs Monitor Module with Respiration Measurement Features: Biopotential signals to included digital signal processor Cortex-M4 based processor (ADSP-CM403F) for customizable measurement and analysis Highly flexible configuration management, incorporating a user configurable field programmable gate array (FPGA) (Lattice iCE40HX1K-TQ144) 12 fully integrated electrocardiogram (ECG) electrode inputs 3 temperature channels 3 invasive blood pressure (IBP) channels Source and detection circuitry for thoracic impedance measurement 1 driver output Wideband performance for pacer detection (available on 2 electrode channels) supporting the user algorithm Self diagnostic and calibration circuitry Configurable lead detection Connector interfaced, small form factor module for ease of system design and implementation Robust, with electromagnetic interference (EMI), shock, and vibration resistant packaging

1.25 GHz Dual Integrated DCL with PPMU, Level Setting DACs, and On-Chip Calibration Registers Features: 1.25 GHz, 2.5 Gbps data rate 3-level driver with high-Z and reflection clamps Window and differential comparators ±25 mA active load Per pin parametric measurement unit (PMU) with a −1.5 V to +4.5 V range Low leakage mode (typically <5 nA) Integrated 16-bit DACs with offset and gain correction 1.2 W power dissipation per channel (ADATE320) 1.3 W power dissipation per channel (ADATE320-1) See data sheet for additional features

Stereo PDM to I2S/TDM Converter Features: 2 channels of PDM audio inputs from digital microphones 64× decimation ratio of PDM to PCM audio data 24-bit resolution to support high sound pressure level (SPL) microphones 126 dB A-weighted SNR 4 kHz to 96 kHz output sampling rate Bit clock rates of 64×, 128×, 192×, 256×, 384×, or 512× the output sampling rate Automatic PDM clock generation Automatic power-down when BCLK is removed 0.36 mA DVDD operating current at 48 kHz sampling rate and 1.8 V supply Slave I2S or TDM output interface Up to TDM-16 supported Configurable TDM slots I/O supply voltage from 1.70 V to 3.63 V DVDD core supply voltage from 1.10 V to 1.98 V 4 μA typical DVDD shutdown current 9-ball, 1.26 mm × 1.26 mm, 0.4 mm pitch WLCSP Power-on reset

Single Comparator with Accurate Reference Output Features: High accuracy reference output voltage: 1 V ± 0.9% Single-supply voltage operation: 2.3 V to 5.5 V Rail-to-rail common-mode input voltage range Low input offset voltage across VCMR: 1 mV typical Guarantees comparator output logic low from VCC = 0.9 V to undervoltage lockout (UVLO) Operating temperature range: −40°C to +125°C Package type: 8-lead, narrow body SOIC

Dual Comparator with Accurate Reference Output Features: High accuracy reference output voltage: 1 V ± 0.9% Single-supply voltage operation: 2.3 V to 5.5 V Rail-to-rail common-mode input voltage range Low input offset voltage across VCMR: 1 mV typical Guarantees comparator output logic low from VCC = 0.9 V to undervoltage lockout (UVLO) Operating temperature range: −40°C to +125°C Package type: 10-lead MSOP

Four-String, White LED Driver for LCD Backlight Applications Features: White LED driver based on an inductive boost controller Wide input voltage range: 4.5V to 40 V Adaptive output voltage to minimize power dissipation Adjustable operating frequency: 200 kHz to 1.2 MHz Programmable UVLO Programmable soft start time for boost converter Programmable external MOSFET switching rising/falling time Drives up to 4 LED current sinks with internal MOSFETs Brightness control with PWM input Adjustable LED current: 40 mA to 200 mA Headroom control to maximize efficiency LED dimming frequency: up to 25 kHz PWM dimming at 300 Hz: 1000:1 Open-drain fault indicator LED open and LED short fault protection Thermal shutdown Undervoltage lockout (UVLO) 24-lead, 4 mm × 4 mm LFCSP

CCD TOF Signal Processor with Programmable Timing and V-Driver Features: 12-bit, 45 MHz ADC CDS with variable gain 0 dB to 36 dB, 10-bit VGA Black level clamp with variable level control Precision Timing core with 174 ps resolution Integrated, 7-channel H-driver and RG clock drivers 7-channel LD driver Integrated 16-channel V-driver Complete on-chip ISA timing generator I2C serial interface MIPI CSI-2 transmit interface with support for 1 or 2 data lanes On-chip driver for external crystal 8 GPOs 6 mm × 6 mm, 117-ball WLCSP package with 0.5 mm pitch

Isolated 4 A Dual-Channel Gate Driver Features: 4 A peak output current Precise timing characteristics 60 ns maximum isolator and driver propagation delay 5 ns maximum channel-to-channel matching High junction temperature operation: 125°C 3.3 V to 5 V input logic 7.6 V to 18 V output drive Undervoltage lockout (UVLO) at 7.0 V VDD2 Automotive versions qualified per AEC-Q100 See data sheet for additional features ADuM3221-EP supports defense and aerospace applications (AQEC standard) Download ADuM3221-EP data sheet (pdf) Military temperature range: −55°C to +125°C Controlled manufacturing baseline 1 assembly/test site 1 fabrication site Enhanced product change notification Qualification data available on request V62/16622 DSCC Drawing Number

Triple-Channel, Digital Isolator, Enhanced System-Level ESD Reliability (2/1 channel directionality) Features: Enhanced system-level ESD performance per IEC 61000-4-x Low power operation 5 V operation 2.0 mA per channel maximum at 0 Mbps to 2 Mbps 4.1 mA per channel maximum at 10 Mbps 36 mA per channel maximum at 90 Mbps 3.3 V operation 1.0 mA per channel maximum at 0 Mbps to 2 Mbps 2.8 mA per channel maximum at 10 Mbps 17 mA per channel maximum at 90 Mbps Bidirectional communication 3.3 V/5 V level translation High temperature operation: 105°C High data rate: dc to 90 Mbps (NRZ) Precise timing characteristics 2 ns maximum pulse width distortion 2 ns maximum channel-to-channel matching High common-mode transient immunity: >25 kV/μs Output enable function 16-lead SOIC wide body, RoHS-compliant package Safety and regulatory approvals UL recognition: 2500 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A VDE Certificate of Conformity DIN V VDE V 0884-10 (VDE V 0884-10): 2006-12 VIORM = 560 V peak CQC Certification per GB4943.1-2011

Quad-Channel, Digital Isolator, Enhanced System-Level ESD Reliability Features: For AEC-Q100 Automotive Qualified Devices Specifications view ADuM340xW data sheet Enhanced system-level ESD performance per IEC 61000-4-x Bidirectional communication 3 V/5 V level translation High temperature operation: 105°C High data rate: dc to 90 Mbps (NRZ) See data sheet for additional featuresADuM3400-EP supports defense and aerospace applications (AQEC standard) Download ADuM3400-EP data sheet (pdf) Military temperature range (−55°C to +125°C) Controlled manufacturing baseline One assembly/test site One fabrication site Enhanced product change notification Qualification data available on request V62/14629 DSCC Drawing Number

Quad-Channel, Digital Isolator, Enhanced System-Level ESD Reliability Features: For AEC-Q100 Automotive Qualified Devices Specifications view ADuM340xW data sheet Enhanced system-level ESD performance per IEC 61000-4-x Bidirectional communication 3 V/5 V level translation High temperature operation: 105°C High data rate: dc to 90 Mbps (NRZ) See data sheet for additional featuresADuM3401-EP supports defense and aerospace applications (AQEC standard) Download ADuM3401-EP data sheet (pdf) Military temperature range (−55°C to +125°C) Controlled manufacturing baseline One assembly/test site One fabrication site Enhanced product change notification Qualification data available on request V62/14630 DSCC Drawing Number

Isolated Switching Regulators (4/0 Channel Directionality) Features: Isolated PWM Controller Integrated transformer driver Regulated adjustable output: 3.3 V to 24 V 2 W output power 70% efficiency at guaranteed load of 400 mA at 5.0 V output Quad dc-to-25 Mbps (NRZ) signal isolation channels 20-lead SSOP package High temperature operation: 105°C High common-mode transient immunity: >25 kV/μs 200 kHz to 1 MHz adjustable oscillator frequency Soft start function at power-up Pulse-by-pulse overcurrent protection Thermal shutdown 2500 V rms isolation Evaluation Board available Automotive Qualified

Isolated Switching Regulators (4/0 Channel Directionality) Features: Isolated PWM Controller Integrated transformer driver Regulated adjustable output: 3.3 V to 24 V 2 W output power 70% efficiency at guaranteed load of 400 mA at 5.0 V output Quad dc-to-25 Mbps (NRZ) signal isolation channels 20-lead SSOP package High temperature operation: 105°C High common-mode transient immunity: >25 kV/μs 200 kHz to 1 MHz adjustable oscillator frequency Soft start function at power-up Pulse-by-pulse overcurrent protection Thermal shutdown 2500 V rms isolation Evaluation Board available Automotive Qualified

Isolated Switching Regulators (4/0 Channel Directionality) Features: Isolated PWM Controller Integrated transformer driver Regulated adjustable output: 3.3 V to 24 V 2 W output power 70% efficiency at guaranteed load of 400 mA at 5.0 V output Quad dc-to-25 Mbps (NRZ) signal isolation channels 20-lead SSOP package High temperature operation: 105°C High common-mode transient immunity: >25 kV/μs 200 kHz to 1 MHz adjustable oscillator frequency Soft start function at power-up Pulse-by-pulse overcurrent protection Thermal shutdown 2500 V rms isolation Evaluation Board available Automotive Qualified

Isolated Switching Regulators (3/1 Channel Directionality) Features: Isolated PWM Controller Integrated transformer driver Regulated adjustable output: 3.3 V to 24 V 2 W output power 70% efficiency at guaranteed load of 400 mA at 5.0 V output Quad dc-to-25 Mbps (NRZ) signal isolation channels 20-lead SSOP package High temperature operation: 105°C High common-mode transient immunity: >25 kV/μs 200 kHz to 1 MHz adjustable oscillator frequency Soft start function at power-up Pulse-by-pulse overcurrent protection Thermal shutdown 2500 V rms isolation Evaluation Board available Automotive Qualified