5 kV RMS/3.75 kV RMS, Dual LVDS Gigabit Isolator (0 Reverse Channels) Features: 5 kV rms and 3.75 kV rms LVDS isolators Complies with TIA/EIA-644-A LVDS standard Multiple dual-channel configurations Any data rate up to 1.1 Gbps switching with low jitter 4 ns typical propagation delay 2.6 ps rms typical random jitter, rms 90 ps typical peak-to-peak total jitter at 1.1 Gbps 2.5 V or 3.3 V supplies −75 dBc power supply ripple rejection, phase spur level Glitch immunity ±8 kV IEC 61000-4-2 ESD protection across isolation barrier High common-mode transient immunity: >25 kV/μs Passes EN 55022 Class B radiated emissions limits with 1.1 Gbps PRBS Safety and regulatory approvals (20-lead SOIC_W package) UL (pending): 5000 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A (pending) VDE certificate of conformity (pending) DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 VIORM = 424 VPEAK Fail-safe output high for open, short, and terminated input conditions (ADN4655/ADN4656) Operating temperature range: −40°C to +125°C 7.8 mm minimum creepage and clearance

Ultracompact 1.5 A Thermoelectric Cooler (TEC) Controller Features: Patented high efficiency single inductor architecture Integrated low RDSON MOSFETs for the TEC controller TEC voltage and current operation monitoring No external sense resistor required Independent TEC heating and cooling current limits settings Programmable maximum TEC voltage 2.0 MHz PWM driver switching frequency External synchronization Two integrated zero drift, rail-to-rail chopper amplifiers Capable of NTC or RTD thermal sensors 2.50 V reference output with 1% accuracy Temperature lock indicator Available in a 25-ball, 2.5 mm × 2.5 mm WLCSP or in a 24-lead, 4 mm × 4 mm LFCSP AEC-Q100 qualified for automotive applications

Three-Channel, Isolated Micropower Management Unit with Seven Digital Isolators Features: Wide input supply voltage range: 4.5 V to 60 V Integrated flyback power switch Generates isolated, independent bipolar outputs and factory programmable buck output VOUT1: 21 V, 24 V or 6 V to 28 V VOUT2: 5.15 V, 5.0 V, or 3.3 V VOUT3: −24 V to −5 V Uses a 1:1 ratio transformer for simplified transformer design Peak current limiting and OVP for flyback, buck, and inverting regulators Precision enable input and power-good output Adjustable switching frequency via SYNC input Internal compensation and soft start control per regulator High speed, low propagation delay, SPI signal isolation channels Three, 100 kbps general-purpose isolated data channels 9 mm × 7 mm LFCSP form factor enables small overall solution size −40°C to +125°C operating junction temperature range Conforms to CISPR11 Class B radiated emission limits Safety and regulatory approvals (pending) UL recognition: 2500 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A 300 V rms basic insulation between slave, master, and field power domains (IEC 61010-1, pending) VDE certificate of conformity DIN V VDE 0884-10 (VDE 0884-10):2006-12 VIORM = 565 VPEAK

Three-Channel, Isolated Micropower Management Unit with Seven Digital Isolators Features: Wide input supply voltage range: 4.5 V to 60 V Integrated flyback power switch Generates isolated, independent bipolar outputs and factory programmable buck output VOUT1: 21 V, 24 V or 6 V to 28 V VOUT2: 5.15 V, 5.0 V, or 3.3 V VOUT3: −24 V to −5 V Uses a 1:1 ratio transformer for simplified transformer design Peak current limiting and OVP for flyback, buck, and inverting regulators Precision enable input and power-good output Adjustable switching frequency via SYNC input Internal compensation and soft start control per regulator High speed, low propagation delay, SPI signal isolation channels Three, 100 kbps general-purpose isolated data channels 9 mm × 7 mm LFCSP form factor enables small overall solution size −40°C to +125°C operating junction temperature range Conforms to CISPR11 Class B radiated emission limits Safety and regulatory approvals (pending) UL recognition: 2500 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A 300 V rms basic insulation between slave, master, and field power domains (IEC 61010-1, pending) VDE certificate of conformity DIN V VDE 0884-10 (VDE 0884-10):2006-12 VIORM = 565 VPEAK

Three-Channel, Isolated Micropower Management Unit with Seven Digital Isolators Features: Wide input supply voltage range: 4.5 V to 60 V Integrated flyback power switch Generates isolated, independent bipolar outputs and factory programmable buck output VOUT1: 21 V, 24 V or 6 V to 28 V VOUT2: 5.15 V, 5.0 V, or 3.3 V VOUT3: −24 V to −5 V Uses a 1:1 ratio transformer for simplified transformer design Peak current limiting and OVP for flyback, buck, and inverting regulators Precision enable input and power-good output Adjustable switching frequency via SYNC input Internal compensation and soft start control per regulator High speed, low propagation delay, SPI signal isolation channels Three, 100 kbps general-purpose isolated data channels 9 mm × 7 mm LFCSP form factor enables small overall solution size −40°C to +125°C operating junction temperature range Conforms to CISPR11 Class B radiated emission limits Safety and regulatory approvals (pending) UL recognition: 2500 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A 300 V rms basic insulation between slave, master, and field power domains (IEC 61010-1, pending) VDE certificate of conformity DIN V VDE 0884-10 (VDE 0884-10):2006-12 VIORM = 565 VPEAK

Three-Channel, Isolated Micropower Management Unit with Seven Digital Isolators Features: Wide input supply voltage range: 4.5 V to 60 V Integrated flyback power switch Generates isolated, independent bipolar outputs and factory programmable buck output VOUT1: 21 V, 24 V or 6 V to 28 V VOUT2: 5.15 V, 5.0 V, or 3.3 V VOUT3: −24 V to −5 V Uses a 1:1 ratio transformer for simplified transformer design Peak current limiting and OVP for flyback, buck, and inverting regulators Precision enable input and power-good output Adjustable switching frequency via SYNC input Internal compensation and soft start control per regulator High speed, low propagation delay, SPI signal isolation channels Three, 100 kbps general-purpose isolated data channels 9 mm × 7 mm LFCSP form factor enables small overall solution size −40°C to +125°C operating junction temperature range Conforms to CISPR11 Class B radiated emission limits Safety and regulatory approvals (pending) UL recognition: 2500 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A 300 V rms basic insulation between slave, master, and field power domains (IEC 61010-1, pending) VDE certificate of conformity DIN V VDE 0884-10 (VDE 0884-10):2006-12 VIORM = 565 VPEAK

Three-Channel, Isolated Micropower Management Unit with Seven Digital Isolators Features: Wide input supply voltage range: 4.5 V to 60 V Integrated flyback power switch Generates isolated, independent bipolar outputs and factory programmable buck output VOUT1: 21 V, 24 V or 6 V to 28 V VOUT2: 5.15 V, 5.0 V, or 3.3 V VOUT3: −24 V to −5 V Uses a 1:1 ratio transformer for simplified transformer design Peak current limiting and OVP for flyback, buck, and inverting regulators Precision enable input and power-good output Adjustable switching frequency via SYNC input Internal compensation and soft start control per regulator High speed, low propagation delay, SPI signal isolation channels Three, 100 kbps general-purpose isolated data channels 9 mm × 7 mm LFCSP form factor enables small overall solution size −40°C to +125°C operating junction temperature range Conforms to CISPR11 Class B radiated emission limits Safety and regulatory approvals (pending) UL recognition: 2500 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A 300 V rms basic insulation between slave, master, and field power domains (IEC 61010-1, pending) VDE certificate of conformity DIN V VDE 0884-10 (VDE 0884-10):2006-12 VIORM = 565 VPEAK

Three-Channel, Isolated Micropower Management Unit with Seven Digital Isolators Features: Wide input supply voltage range: 4.5 V to 60 V Integrated flyback power switch Generates isolated, independent bipolar outputs and factory programmable buck output VOUT1: 21 V, 24 V or 6 V to 28 V VOUT2: 5.15 V, 5.0 V, or 3.3 V VOUT3: −24 V to −5 V Uses a 1:1 ratio transformer for simplified transformer design Peak current limiting and OVP for flyback, buck, and inverting regulators Precision enable input and power-good output Adjustable switching frequency via SYNC input Internal compensation and soft start control per regulator High speed, low propagation delay, SPI signal isolation channels Three, 100 kbps general-purpose isolated data channels 9 mm × 7 mm LFCSP form factor enables small overall solution size −40°C to +125°C operating junction temperature range Conforms to CISPR11 Class B radiated emission limits Safety and regulatory approvals (pending) UL recognition: 2500 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A 300 V rms basic insulation between slave, master, and field power domains (IEC 61010-1, pending) VDE certificate of conformity DIN V VDE 0884-10 (VDE 0884-10):2006-12 VIORM = 565 VPEAK

Two-Channel, Isolated Micropower Management Unit with Seven Digital Isolators Features: Wide input supply voltage range: 4.5 V to 60 V Integrated flyback power switch Generates two isolated, well regulated independent outputs VOUT1: 24 V or 6 V to 28 V VOUT2: 3.3 V, 5.0 V, or 5.15 V Uses a 1:1 ratio transformer for simplified transformer design Peak current limiting and OVP for flyback and buck regulators Precision enable input and power-good output Adjustable switching frequency via SYNC input Internal compensation and soft start control per regulator High speed, low propagation delay, SPI signal isolation channels Three 100 kbps general-purpose isolated data channels 41-lead, 9 mm × 7 mm LFCSP form factor enables small overall solution size −40°C to +125°C operating junction temperature range Safety and regulatory approvals (pending) CISPR11 Class B radiated emission UL recognition: 2500 V rms for 1 minute duration per UL 1577 CSA Component Acceptance Notice 5A 300 V rms basic insulation between slave, master, and field power domains (IEC 61010-1, pending) VDE certificate of conformity DIN V VDE 0884-10 (VDE 0884-10):2006-12 VIORM = 565 VPEAK

Two-Channel, Isolated Micropower Management Unit with Seven Digital Isolators Features: Wide input supply voltage range: 4.5 V to 60 V Integrated flyback power switch Generates two isolated, well regulated independent outputs VOUT1: 24 V or 6 V to 28 V VOUT2: 3.3 V, 5.0 V, or 5.15 V Uses a 1:1 ratio transformer for simplified transformer design Peak current limiting and OVP for flyback and buck regulators Precision enable input and power-good output Adjustable switching frequency via SYNC input Internal compensation and soft start control per regulator High speed, low propagation delay, SPI signal isolation channels Three 100 kbps general-purpose isolated data channels 41-lead, 9 mm × 7 mm LFCSP form factor enables small overall solution size −40°C to +125°C operating junction temperature range Safety and regulatory approvals (pending) CISPR11 Class B radiated emission UL recognition: 2500 V rms for 1 minute duration per UL 1577 CSA Component Acceptance Notice 5A 300 V rms basic insulation between slave, master, and field power domains (IEC 61010-1, pending) VDE certificate of conformity DIN V VDE 0884-10 (VDE 0884-10):2006-12 VIORM = 565 VPEAK

Digital Controller for Isolated Power Supply with PMBus Interface Features: Versatile digital voltage mode controller High speed input voltage feedforward control 4 pulse-width modulation (PWM) logic outputs with 625 ps resolution Switching frequency: 49 kHz to 625 kHz Frequency synchronization as slave device Pulse skipping power saving mode Prebias startup Conditional overvoltage protection Extensive fault detection and protection PMBus compliant Graphical user interface (GUI) for ease of programming See datasheet for additional features

Digital Controller for Isolated Power Supply with PMBus Interface Features: Versatile digital voltage mode controller High speed input voltage feedforward control 6 pulse-width modulation (PWM) logic outputs with 625 ps resolution Switching frequency: 49 kHz to 625 kHz Frequency synchronization as master and slave device Multiple energy saving modes Adaptive dead time compensation for efficiency optimization Low device power consumption: 100 mW typical Extensive fault detection and protection PMBus compliant Direct parallel control for power supplies without OR’ing devices Accurate droop current share Pre-bias startup Reverse current protection Conditional overvoltage protection Graphical user interface (GUI) for ease of programming On-board EEPROM for programming and data storage Available in a 24-lead, 4 mm × 4 mm LFCSP −40°C to +125°C operating temperature

Digital Controller for Power Supply Applications with PMBus Interface Features: −40°C to +125°C operation with EEPROM data retention of 15 years at 125°C PMBus Revision 1.2 compliant 32-bit password protection with command masking 64 address selections (16 base addresses, expandable to 64) 6 PWM control signals, 625 ps resolution Duty cycle double update rate Digital control loop (PID + additional pole or zero configurability) Programmable loop filters (CCM, DCM, low/normal temperature) Frequency synchronization Soft start and soft stop functionality Average and peak constant current mode External PN junction temperature sensing 4 GPIOs (2 GPIOs configurable as active clamp snubber PWMs) Fast line voltage feedforward Adaptive dead time compensation for improved efficiency Extended black box data recorder for fault recording See datasheet for additional features

Isolated Synchronous Flyback Controller with IntegratediCoupler Features: Current mode controller for flyback topology ADP1071-1: programmable LLM or CCM for high VIN applications ADP1071-2: forced CCM operation Programmable slope compensation Integrated 5 kV isolation (wide body SOIC package) or 3.0 kV (LGA package) rated dielectric isolation voltage with Analog Devices, Inc., patented iCoupler technology Wide voltage supply range Primary VDD: up to 60 V (ADP1071-2 only) Secondary VDD2: up to 36 V Integrated 1 A primary side MOSFET driver Integrated 1 A secondary side MOSFET drivers for synchronous rectification Integrated error amplifier and <1% accurate reference voltage Programmable frequency range: 50 kHz to 600 kHz Duty cycle clamp limit 85% Programmable soft start and soft start from precharged load Protection features such as short circuit, output overvoltage, and overtemperature protection Power saving LLM using MODE pin (ADP1071-1only) Cycle by cycle input overcurrent protection Precision enable UVLO with hysteresis Frequency synchronization Safety and regulatory approvals (pending) UL recognition 5000 V rms for 1 minute per UL 1577 (for wide body SOIC package) 3000 V rms for 1 minute per UL 1577 (for LGA package) CSA Component Acceptance Notice 5A VDE certificate of conformity DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 VIORM = 849 V peak (for wide body SOIC package) VIORM = 565 V peak (for LGA package) CQC certification per GB4943.1-2011 Available in 16-lead SOIC_W package and 24 terminal LGA package

Isolated Synchronous Flyback Controller with IntegratediCoupler Features: Current mode controller for flyback topology ADP1071-1: programmable LLM or CCM for high VIN applications ADP1071-2: forced CCM operation Programmable slope compensation Integrated 5 kV isolation (wide body SOIC package) or 3.0 kV (LGA package) rated dielectric isolation voltage with Analog Devices, Inc., patented iCoupler technology Wide voltage supply range Primary VDD: up to 60 V (ADP1071-2 only) Secondary VDD2: up to 36 V Integrated 1 A primary side MOSFET driver Integrated 1 A secondary side MOSFET drivers for synchronous rectification Integrated error amplifier and <1% accurate reference voltage Programmable frequency range: 50 kHz to 600 kHz Duty cycle clamp limit 85% Programmable soft start and soft start from precharged load Protection features such as short circuit, output overvoltage, and overtemperature protection Power saving LLM using MODE pin (ADP1071-1only) Cycle by cycle input overcurrent protection Precision enable UVLO with hysteresis Frequency synchronization Safety and regulatory approvals (pending) UL recognition 5000 V rms for 1 minute per UL 1577 (for wide body SOIC package) 3000 V rms for 1 minute per UL 1577 (for LGA package) CSA Component Acceptance Notice 5A VDE certificate of conformity DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 VIORM = 849 V peak (for wide body SOIC package) VIORM = 565 V peak (for LGA package) CQC certification per GB4943.1-2011 Available in 16-lead SOIC_W package and 24 terminal LGA package

Isolated Synchronous Flyback Controller with IntegratediCoupler Features: Current mode controller for flyback topology ADP1071-1: programmable LLM or CCM for high VIN applications ADP1071-2: forced CCM operation Programmable slope compensation Integrated 5 kV isolation (wide body SOIC package) or 3.0 kV (LGA package) rated dielectric isolation voltage with Analog Devices, Inc., patented iCoupler technology Wide voltage supply range Primary VDD: up to 60 V (ADP1071-2 only) Secondary VDD2: up to 36 V Integrated 1 A primary side MOSFET driver Integrated 1 A secondary side MOSFET drivers for synchronous rectification Integrated error amplifier and <1% accurate reference voltage Programmable frequency range: 50 kHz to 600 kHz Duty cycle clamp limit 85% Programmable soft start and soft start from precharged load Protection features such as short circuit, output overvoltage, and overtemperature protection Power saving LLM using MODE pin (ADP1071-1only) Cycle by cycle input overcurrent protection Precision enable UVLO with hysteresis Frequency synchronization Safety and regulatory approvals (pending) UL recognition 5000 V rms for 1 minute per UL 1577 (for wide body SOIC package) 3000 V rms for 1 minute per UL 1577 (for LGA package) CSA Component Acceptance Notice 5A VDE certificate of conformity DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 VIORM = 849 V peak (for wide body SOIC package) VIORM = 565 V peak (for LGA package) CQC certification per GB4943.1-2011 Available in 16-lead SOIC_W package and 24 terminal LGA package

Isolated, Synchronous Forward Controller with Active Clamp and iCoupler Features: Current mode controller for active clamp forward topology Integrated 5 kV (wide body SOIC package) or 3.0 kV (LGA package) rated dielectric isolation voltage with Analog Devices, Inc., patented iCoupler technology Wide voltage supply range Primary VIN: up to 60 V Secondary VDD2: up to 36 V Integrated 1 A primary side MOSFET driver for power switch and active clamp reset switch Integrated 1 A secondary side MOSFET drivers for synchronous rectification Integrated error amplifier and <1% accurate reference voltage Programmable slope compensation Programmable frequency range: 50 kHz to 600 kHz typical Frequency synchronization Programmable maximum duty cycle limit Programmable soft start Smooth soft start from precharged load Programmable dead time Power saving light load mode using MODE pin Protection features such as short circuit, output overvoltage, and overtemperature protection Cycle-by-cycle input overcurrent protection Precision enable UVLO with hysteresis PGOOD pin for system flagging Tracking function from secondary side Remote (secondary side) shutdown/reset function Safety and regulatory approvals (pending) UL recognition 5000 V rms for 1 minute per UL 1577 (for wide body SOIC package) 3000 V rms for 1 minute per UL 1577 (for LGA package) CSA component acceptance notice 5A VDE certificate of conformity DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 VIORM = 849 V peak (for wide body SOIC package) VIORM = 560 V peak (for LGA package) CQC certification per GB4943.1-2011 Available in 24-lead SOIC_W package and 24-terminal LGA package AEC-Q100 Qualified for Automotive Applications

Ultralow Noise, 200 mA, CMOS Linear Regulator Features: Ultralow noise: 9 μV rms No noise bypass capacitor required Stable with 1 μF ceramic input and output capacitors Maximum output current: 200 mA Input voltage range: 2.2 V to 5.5 V Low quiescent current IGND = 10 μA with IOUT = 0 μA IGND = 265 μA with IOUT = 200 mA Low shutdown current: <1 μA Low dropout voltage: 135 mV at IOUT = 200 mA Initial accuracy: ±1% Accuracy over line, load, and temperature: ±2.5% 16 fixed output voltage options: 1.1 V to 3.3 V PSRR performance of 70 dB at 10 kHz Current-limit and thermal overload protection Logic controlled enable Internal pull-down resistor on EN input 5-lead TSOT package 6-lead LFCSP package 4-ball, 0.4 mm pitch WLCSP AEC-Q100 qualified for automotive applicationsADP151-EP supports defense and aerospace applications (AQEC standard) Download ADP151-EP data sheet (pdf) Military temperature range (−55°C to +125°C) Controlled manufacturing baseline One assembly/test site One fabrication site Enhanced product change notification Qualification data available on request V62/12666 DSCC Drawing Number

Ultralow Noise, 200 mA, CMOS Linear Regulator Features: Ultralow noise: 9 μV rms No noise bypass capacitor required Stable with 1 μF ceramic input and output capacitors Maximum output current: 200 mA Input voltage range: 2.2 V to 5.5 V Low quiescent current IGND = 10 μA with IOUT = 0 μA IGND = 265 μA with IOUT = 200 mA Low shutdown current: <1 μA Low dropout voltage: 135 mV at IOUT = 200 mA Initial accuracy: ±1% Accuracy over line, load, and temperature: ±2.5% 16 fixed output voltage options: 1.1 V to 3.3 V PSRR performance of 70 dB at 10 kHz Current-limit and thermal overload protection Logic controlled enable Internal pull-down resistor on EN input 5-lead TSOT package 6-lead LFCSP package 4-ball, 0.4 mm pitch WLCSP AEC-Q100 qualified for automotive applicationsADP151-EP supports defense and aerospace applications (AQEC standard) Download ADP151-EP data sheet (pdf) Military temperature range (−55°C to +125°C) Controlled manufacturing baseline One assembly/test site One fabrication site Enhanced product change notification Qualification data available on request V62/12666 DSCC Drawing Number

Ultralow Noise, 200 mA, CMOS Linear Regulator Features: Ultralow noise: 9 μV rms No noise bypass capacitor required Stable with 1 μF ceramic input and output capacitors Maximum output current: 200 mA Input voltage range: 2.2 V to 5.5 V Low quiescent current IGND = 10 μA with IOUT = 0 μA IGND = 265 μA with IOUT = 200 mA Low shutdown current: <1 μA Low dropout voltage: 135 mV at IOUT = 200 mA Initial accuracy: ±1% Accuracy over line, load, and temperature: ±2.5% 16 fixed output voltage options: 1.1 V to 3.3 V PSRR performance of 70 dB at 10 kHz Current-limit and thermal overload protection Logic controlled enable Internal pull-down resistor on EN input 5-lead TSOT package 6-lead LFCSP package 4-ball, 0.4 mm pitch WLCSP AEC-Q100 qualified for automotive applicationsADP151-EP supports defense and aerospace applications (AQEC standard) Download ADP151-EP data sheet (pdf) Military temperature range (−55°C to +125°C) Controlled manufacturing baseline One assembly/test site One fabrication site Enhanced product change notification Qualification data available on request V62/12666 DSCC Drawing Number