800MHz to 1.5GHz Direct Conversion Quadrature Demodulator Features: Frequency Range: 800MHz to 1.5GHz High IIP3: 21.5dBm at 900MHz High IIP2: 52dBm Noise Figure: 12.8dB at 900MHz Conversion Gain: 4.3dB at 900MHz I/Q Gain Mismatch: 0.2dB Shutdown Mode 16-Lead QFN 4mm x 4mm Package with Exposed Pad

750MHz Gain of 1 Triple 2:1Video Multiplexer Features: 750MHz -3dB Small Signal Bandwidth 450MHz -3dB 2VP-P Large-Signal Bandwidth 120MHz ±0.1dB Bandwidth High Slew Rate: 2100V/μs Fixed Gain of 1; No External Resistors Required 72dB Channel Separation at 10MHz 52dB Channel Separation at 100MHz -84dBc 2nd Harmonic Distortion at 10MHz, 2VP-P -87dBc 3rd Harmonic Distortion at 10MHz, 2VP-P Low Supply Current: 9.5mA per Amplifi er 6.5ns 0.1% Settling Time for 2V Step ISS ≤ 330μA per Amplifier When Disabled Differential Gain of 0.033%, Differential Phase of 0.022° Wide Supply Range: ±2.25V (4.5V) to ±6V (12V) Available in 24-Lead SSOP and 24-Lead QFN Packages

Isolated No-Opto Synchronous Flyback Controller with Wide Input Supply Range Features: Senses Output Voltage Directly from Primary Side Winding—No Opto-Isolator Required Synchronous Driver for High Efficiency Input Voltage Limited Only by External Power Components Accurate Output Regulation without User Trims Switching Frequency from 50kHz to 250kHz Synchronizable Load Compensation Programmable Undervoltage Lockout Available in a Thermally Enhanced 16-Lead TSSOP Package

SmartMesh IP Wireless 802.15.4e System-on-Chip Features: 72-pin 10mm × 10mm QFN package 2.4 GHz, IEEE 802.15.4e System-on-Chip, Complete with Embedded SmartMesh Networking Software >99.999% Network Reliability in the Most Challenging RF Environments Sub 50µA Routing Nodes Serves as either a Wireless Mote, EManager, or Access Point Mote in a SmartMesh IP network These products contain encryption. Import/export restrictions may apply.

SmartMesh IP Wireless 802.15.4e System-on-Chip Features: 72-pin 10mm × 10mm QFN package 2.4 GHz, IEEE 802.15.4e System-on-Chip, Complete with Embedded SmartMesh Networking Software >99.999% Network Reliability in the Most Challenging RF Environments Sub 50µA Routing Nodes Serves as either a Wireless Mote, EManager, or Access Point Mote in a SmartMesh IP network These products contain encryption. Import/export restrictions may apply.

500mA Camera LED Charge Pump Features: Low Noise Constant Frequency Operation High Efficiency: Up to 94% Multi-Mode Operation: 1x, 1.5x or 2x Boost Modes Automatic Mode Switching High Output Current: Up to 500mA Tiny Application Circuit (3mm × 3mm DFN Package All Components <1mm High) Automatic Soft-Start Output Disconnect Open, Shorted LED Protection No Inductors Internal 110m LED Current Sense Resistor 3mm × 3mm 10-Lead DFN Package

3.3V/2.5V Step-Up/Step-Down Charge Pump DC/DC Converter Features: Step-Up/Step-Down Charge Pumps Generate Fixed 3.3V or 2.5V Outputs VIN Range: 1.8V to 5.5V Output Current up to 150mA Automatic Mode Switching Constant Frequency (1.2MHz) Operation in Step-Up Mode Low Dropout Regulator Operation in Step-Down Mode Low No-Load Quiescent Current: IQ = 65µA Built-In Soft-Start Reduces Inrush Current Shutdown Disconnects Load from Input Shutdown Current < 1µA Short-Circuit/Thermal Protection Available in a 6-Lead (2mm × 2mm) DFN Package

Low Noise Regulated Charge Pump in 2 2 DFN Features: Fixed 3.3V or 5V Outputs VIN Range: 1.8V to 4.5V (LTC3204-3.3/LTC3204B-3.3) 2.7V to 5.5V (LTC3204-5/LTC3204B-5) Output Current: Up to 150mA (LTC3204-5/LTC3204B-5) Up to 50mA (LTC3204-3.3/LTC3204B-3.3) Automatic Burst Mode® Operation with IQ = 48µA (LTC3204-3.3/LTC3204-5) Constant Frequency Operation at All Loads (LTC3204B-3.3/LTC3204B-5) Low Noise Constant Frequency (1.2MHz) Operation* Built-In Soft-Start Reduces Inrush Current Shutdown Disconnects Load from Input Shutdown Current <1µA Short-Circuit/Thermal Protection Available in Low Profile 6-Lead DFN Package

14-Bit, 105Msps ADC Features: Sample Rate: 105Msps/80Msps 77.3dBFS Noise Floor 98dB SFDR SFDR >82dB at 250MHz (1.5VP-P Input Range) PGA Front End (2.25VP-P or 1.5VP-P Input Range) 700MHz Full Power Bandwidth S/H Optional Internal Dither Optional Data Output Randomizer Single 3.3V Supply Power Dissipation: 947mW/762mW Optional Clock Duty Cycle Stabilizer Out-of-Range Indicator Pin-Compatible Family 105Msps: LTC2207 (16-Bit), LTC2207-14 (14-Bit) 80Msps: LTC2206 (16-Bit), LTC2206-14 (14-Bit) 65Msps: LTC2205 (16-Bit), LTC2205-14 (14-Bit) 40Msps: LTC2204 (16-Bit) 25Msps: LTC2203 (16-Bit) Single-Ended Clock 10Msps: LTC2202 (16-Bit) Single-Ended Clock 48-Pin 7mm × 7mm QFN Package

14-Bit, 105Msps ADC Features: Sample Rate: 105Msps/80Msps 77.3dBFS Noise Floor 98dB SFDR SFDR >82dB at 250MHz (1.5VP-P Input Range) PGA Front End (2.25VP-P or 1.5VP-P Input Range) 700MHz Full Power Bandwidth S/H Optional Internal Dither Optional Data Output Randomizer Single 3.3V Supply Power Dissipation: 947mW/762mW Optional Clock Duty Cycle Stabilizer Out-of-Range Indicator Pin-Compatible Family 105Msps: LTC2207 (16-Bit), LTC2207-14 (14-Bit) 80Msps: LTC2206 (16-Bit), LTC2206-14 (14-Bit) 65Msps: LTC2205 (16-Bit), LTC2205-14 (14-Bit) 40Msps: LTC2204 (16-Bit) 25Msps: LTC2203 (16-Bit) Single-Ended Clock 10Msps: LTC2202 (16-Bit) Single-Ended Clock 48-Pin 7mm × 7mm QFN Package

620MHz - 1100MHz High Linearity Direct Quadrature Modulator Features: Direct Conversion from Baseband to RF High Output: –4.2dB Conversion Gain High OIP3: 21.7dBm at 900MHz Low Output Noise Floor at 20MHz Offset: No RF: –159dBm/Hz POUT = 4dBm: –153.3dBm/Hz Low Carrier Leakage: –42dBm at 900MHz High Image Rejection: –53dBc at 900MHz 3-Ch CDMA2000 ACPR: –70.4dBc at 900MHz Integrated LO Buffer and LO Quadrature Phase Generator 50Ω AC-Coupled Single-Ended LO and RF Ports High Impedance DC Interface to Baseband Input with 0.5V Common Mode Voltage 16-Lead QFN 4mm × 4mm Package

16-Bit ADC with Easy Drive Input Current Cancellation and I2C Interface Features: Easy Drive™ Technology Enables Rail-to-Rail Inputs with Zero Differential Input Current Directly Digitizes High Impedance Sensors with Full Accuracy 600nVRMS Noise, Independent of VREF GND to VCC Input/Reference Common Mode Range 2-Wire I2C Interface Simultaneous 50Hz/60Hz Rejection 2ppm (0.25 LSB) INL, No Missing Codes 1ppm Offset and 15ppm Full-Scale Error No Latency: Digital Filter Settles in a Single Cycle Single Supply 2.7V to 5.5V Operation Internal Oscillator Six Addresses Available Available in a Tiny (3mm × 3mm) 10-Lead DFN Package

Low Noise, Low Distortion Fully Differential Input/Output Amplifier/Driver Features: Fully Differential Input and Output Wide Supply Range: 2.375V to 12.6V Rail-to-Rail Output Swing Low Noise: 3nV/√Hz Low Distortion, 2VP-P, 1MHz: –94dBc Adjustable Output Common Mode Voltage Unity Gain Stable Gain-Bandwidth: 70MHz Slew Rate: 65V/μs Large Output Current: 85mA DC Voltage Offset <2mV MAX Open-Loop Gain: 100V/mV Low Power Shutdown 8-Pin MSOP or 3mm × 3mm DFN Package

Very Low Noise, Differential Amplifier and 10MHz Lowpass Filter Features: Programmable Differential Gain via Two External Resistors Adjustable Output Common Mode Voltage Operates and Specified with 3V, 5V, ±5V Supplies 0.5dB Ripple 4th Order Lowpass Filter with 10MHz Cutoff 82dB S/N with 3V Supply and 2VP-P Output Low Distortion, 2VP-P , 800Ω Load 1MHz: 88dBc 2nd, 97dBc 3rd 5MHz: 74dBc 2nd, 77dBc 3rd Fully Differential Inputs and Outputs Compatible with Popular Differential Amplifier Pinouts SO-8 and DFN-12 Packages

700MHz to 1050MHz High Linearity Direct Quadrature Modulator Features: Frequency Range: 700MHz to 1050MHz High OIP3: +22.9dBm at 850MHz Low Output Noise Floor at 5MHz Offset: No RF: –160.3dBm/Hz POUT = 4dBm: –154dBm/Hz 3-Ch CDMA2000 ACPR: –71.4dBc at 850MHz Integrated LO Buffer and LO Quadrature Phase Generator 50Ω AC-Coupled Single-Ended LO and RF Ports 50Ω DC Interface to Baseband Inputs Low Carrier Leakage: –43dBm at 850MHz High Image Rejection: –46dBc at 850MHz 16-Lead 4mm × 4mm QFN Package

Low IQ Synchronous Step-Down Controller Features: Wide Output Voltage Range: 0.8V ≤ VOUT ≤ 10V Low Operating Quiescent Current: 80μA OPTI-LOOP® Compensation Minimizes COUT 1% Output Voltage Accuracy Wide VIN Range: 4V to 36V Operation Phase-Lockable Fixed Frequency 140kHz to 650kHz Dual N-Channel MOSFET Synchronous Drive Very Low Dropout Operation: 99% Duty Cycle Adjustable Output Voltage Soft-Start or Tracking Output Current Foldback Limiting Power Good Output Voltage Monitor Clock Output for PolyPhase® Applications Output Overvoltage Protection Low Shutdown IQ: 10μA Internal LDO Powers Gate Drive from VIN or VOUT Selectable Continuous, Pulse-Skipping or Burst Mode® Operation at Light Loads Small 20-Lead TSSOP or 4mm × 5mm QFN Package AEC-Q100 Qualified for Automotive Applications

No RSENSE, Low Input Voltage, Synchronous Step-Down DC/DC Controller Features: No Current Sense Resistor Required All N-Channel MOSFET Synchronous Drive High Current Outputs Possible Constant Frequency Current Mode Operation for Excellent Line and Load Transient Response VIN: 2.75V to 4.5V ±1% 0.6V Reference Low Dropout Operation: 99% Duty Cycle Selectable Frequency (300kHz/550kHz/750kHz) Internal Soft-Start Circuitry Selectable Maximum Peak Current Sense Threshold Digital RUN Control Pin Output Overvoltage Protection Micropower Shutdown: IQ = 7.5µA Tiny Thermally Enhanced Leadless (3mm × 3mm) DFN or 10-Lead MSOP Package

Triple Output LED Driver Features: True Color PWM™ Dimming Delivers Up to 3000:1 Dimming Ratio Built-In Gate Driver for PMOS LED Disconnect Three Independent Driver Channels with 750mA, 45V Internal Switches Operates in Buck, Boost, Buck-Boost Modes CTRL Pin Accurately Sets LED Current Sense Threshold Over a Range of 10mV to 100mV Adjustable Frequency: 330kHz to 2.1MHz Open LED Protection Wide VIN Supply Range: Operation from 3V to 30V Transient Protection to 40V Surface Mount Components 28-Lead (4mm × 5mm) QFN and TSSOP Packages

2GHz Low Noise, Low Distortion Differential ADC Driver for DC-140MHz Features: 2GHz –3dB Bandwidth Fixed Gain of 5V/V (14dB) –91dBc IMD3 at 70MHz (Equivalent OIP3 = 49.3dBm) –81dBc IMD3 at 140MHz (Equivalent OIP3 = 44.5dBm) 1.1nV/√Hz Internal Op Amp Noise 7.3dB Noise Figure Differential Inputs and Outputs 200Ω Input Impedance 2.85V to 3.5V Supply Voltage 45mA Supply Current (135mW) 1V to 1.6V Output Common Mode, Adjustable DC- or AC-Coupled Operation Max Differential Output Swing 4.6VP-P Small 16-Lead 3mm × 3mm × 0.75mm QFN Package

1.6GHz Low Noise, Low Distortion Differential ADC Driver for DC-140MHz Features: 1.6GHz –3dB Bandwidth Fixed Gain of 20V/V (26dB) –85dBc IMD3 at 70MHz (Equivalent OIP3 = 46.5dBm) –72dBc IMD3 at 140MHz (Equivalent OIP3 = 40dBm) 1nV/√Hz Internal Op Amp Noise 1.5nV/√Hz Total Input Referred Noise 6.8dB Noise Figure Differential Inputs and Outputs 50Ω Input Impedance 2.85V to 3.5V Supply Voltage 45mA Supply Current (135mW) 1V to 1.6V Output Common Mode, Adjustable DC- or AC-Coupled Operation Max Differential Output Swing 4.7VP-P Small 16-Lead 3mm × 3mm × 0.75mm QFN Package