DRV88xx Current Recirculation and Decay Modes Application Report
Texas InstrumentsDRV8800/01, DRV8809/10, DRV8811, DRV8821/23 DRV88xx Current Recirculation and Decay Modes Application Report
LMZ35003 Protects Against 60-V Line Transients
Texas InstrumentsThe LMZ35003 wide input voltage 2.5-A Simple Switcher® power module is designed for typicaloperating input voltages of 7 V to 50 V. However with a 65-V absolute maximum input voltage rating theLMZ35003 can be used in applications where the input voltage exceeds 50 V during line transients. The 7V to 50 V operating input voltage range of the LMZ35003 is recommended for the best performanc
Peak Current Control Realization for Boost Circuit Based on C2000 MCU
Texas InstrumentsPeak Current Control Realization for Boost Circuit Based on C2000 MCU written by Chinese engineer
Powering the TMS320C6745 and TMS320C6747 with the TPS650061
Texas InstrumentsTPS650061, TMS320c6745, TMS320C6747 Powering the TMS320C6745 and TMS320C6747 with the TPS650061
TPS22966 Dual Channel Load Switch in Parallel Configuration (Rev. A)
Texas InstrumentsTPS22966 TPS22966 Dual Channel Load Switch in Parallel Configuration
Achieving True Universal Input Capability Using ADS1248 and ADS1148
Texas InstrumentsADS1248, ADS1148 Achieving True Universal Input Capability Using ADS1248 and ADS1148
Low Voltage Reverse Battery Protection Circuit Using TPS61200 Boost Converter
Texas InstrumentsThis application report describes how to implement a reverse-battery-protection feature using the TPS61200 boost converter in applications powered from a single alkaline nickel-cadmium (NiCd) or nickel-metal hydride (NiMH) cell.
Using PWM Output as a Digital-to-Analog Converter on a TMS320C240 DSP
Texas InstrumentsThis paper presents a method for utilizing the on-chip PWM generators on a TMS320C240 DSP for digital-to-analog (D/A) conversion. The method involves analog low-pass filtering the PWM signal to remove high frequency components leaving only the low-frequency content. Theoretical and experimental results are presented to quantify the achievable bit resolution. In addition analog low-pass filter
How to Configure DP838XX for Ethernet Compliance and Loopback Testing
Texas InstrumentsThis application report covers how to setup and configure the DP838xx PHY (using the customer EVM) for Ethernet Physical Layer Compliance (IEEE 802.3), PHY Loopback, and Built in Self-Test (BIST) Pseu
A New Off-line LED Lighting Driver Solution with multi-transformer LLC Control (Rev. A)
Texas InstrumentsA New Off-line LED Lighting Driver Solution with multi-transformer LLC Control
Board-Mount Evaluation of Tin-Plated Component Leads (Rev. A)
Texas InstrumentsBoard-Mount Evaluation of Tin-Plated Component Leads
TMS320DM642 to TMS320DM6437 Migration Guide
Texas InstrumentsThis document describes device considerations for migrating a design based on a TI TMS320DM642 Video/Imaging Fixed-Point Digital Signal Processor (DSP) to one based on a TI TMS320DM6437 Digital Media
Implementing Single-Chip FPGA Power Solutions
Texas InstrumentsImplementing Single-Chip FPGA Power Solutions
TVP5160 3D Noise Reduction Calibration Procedure
Texas InstrumentsTVP5160 3D Noise Reduction Calibration Procedure
Implementing DDR2 PCB Layout on the TMS320C6421 DSP (Rev. C)
Texas InstrumentsThis application report contains implementation instructions for the DDR2 interface contained on the TMS320C6421 digital signal processor (DSP) device. The approach to specifying interface timing for the DDR2 interface is quite different than on previous devices.The previous approach specified device timing in terms of data sheet specifications and simulation models. The system designer was requ
