Application notes from Texas Instruments

Displaying 5941 - 5960 of 6424

Application Notes from Texas Instruments

Power Drive Protection Interrupt

The Power Drive Protection Interrupt (PDPINT) pin is a safety feature that is built into all TMS320C24? DSPs. This feature protects the electrical drive from damage due to any electrical, mechanical o

MSP430 FRAM Technology ? How To and Best Practices

Texas Instruments

FRAM is a non-volatile memory technology that behaves similar to SRAM while enabling a whole host of new applications, but also changing the way firmware should be designed. This application report ou

Sine/Cosine on the TMS320C2xx

Texas Instruments

Sine-wave generators are fundamental building blocks of signal processing systems for use in control applications. This application note describes two different methods for implementing a digital Sine wave generator using the TMS320C2xx. The first method is a fast direct table look-up with linear interpolation to provide Sine waves with a minimum harmonic distortion. The second method realizes th

High Resolution Microstepping Driver With the DRV88xx Series

Texas Instruments

DRV8812, DRV8813, DRV8828, DRV8829 High Resolution Microstepping Driver With the DRV88xx Series

App Nte 1565 LXT972M to DP83848C/I/YB PHYTER Sys Rollovr Doc (Rev. A)

Texas Instruments

This application report provides information about the process to upgrade an existing 10/100 Mb/sEthernet design using Intel’s LXT972M Ethernet Physical Layer (PHY) product our new DP83848C/I/YBPHYTER product.

SPI Bootloader for Hercules TMS570LS04X MCU

Texas Instruments

This application report describes how to communicate with the Hercules™ serial peripheral interface (SPI) bootloader. The SPI bootloader is a small piece of code that can be programmed at the beginning of Flash to act as an application loader as well as an update mechanism for applications running on a Hercules Cortex™-R4 based TMS570LS04x microcontroller.

TLV2370/71/72/73/74/75 EMI Immunity Performance (Rev. A)

Texas Instruments

The electromagnetic interference (EMI) rejection ratio, or EMIRR, describes the EMI immunity of operational amplifiers. An adverse effect that is common to many op amps is a change in the offset voltage as a result of RF signal rectification. An op amp that is more efficient at rejecting this change in offset as a result of EMI has a higher EMIRR and is quantified by a decibel value.

AN097 - Current Savings in CC254x Using the TPS62730 (Rev. B)

Texas Instruments

CC2540, TPS62730 AN097 - Current Savings in CC254x Using the TPS62730

Implementing Real-Time MIDI Music Synthesis Algorithms, ABS/OLA, & SMS-TMS320C32

Texas Instruments

IMPLEMENTING REAL-TIME MIDI MUSIC SYNTHESIS ALGORITHMS, ABS/OLA, & SMS FOR THE TMS320C32 DSP

Precision Absolute Value Circuits

Texas Instruments

You can build a precision absolute value circuit using two op amps and two precision resistors. If you use an op amp and an IC difference amplifier no user supplied precision resistors or resistor adjustments are required. Circuits shown are suitable for precision split supply operation and for single-supply operation. When used with a rail-to-rail op amp the single supply circuit can approach a

AN-1119 Voltage Doubler Design and Analysis (Rev. A)

Texas Instruments

AN-1119 Voltage Doubler Design and Analysis

Interfacing the ADS8364 ADC to the MSP430F149

Texas Instruments

The ADS8364 16-bit parallel output analog-to-digital converter has a number of features that allow for an easy interface to the MSP430x1xx family of microcontrollers. Using ports 1 and 2 of the Texas

MSP430 Isolated FET Interface

Texas Instruments

This application report describes how to build an isolated FET interface for the MSP430 Flash Emulation Tool (FET). When developing and debugging line-powered MSP430 applications such as motor contro

Implementing a 60-W End-to-End PoE System

Texas Instruments

Specialized applications such as WiMax base stations may require more than 50 W of power, but the current IEEE 802.3at standard defines 25.5-W, two-pair systems. This application report presents a non

Prototyping the TI TMS320C40 to the Cypress VIC068/VAC068 VME Interface

Texas Instruments

The VIC068/VA068 is designed to interface with the Motorola 68000 microprocessor family so interfacing it to the TMS320C40 digital signal processor (DSP) requires a logic simulation or configurable prototype. This document focuses on the details of the hardware design and the programmable logic source code interfacing the VIC068 to the TMS320C40 32-bit parallel DSP. It provides the details on the

TP3420A S Interface Device (SID) User's Guide

Texas Instruments

TP3420A S Interface Device (SID) User's Guide

Q3 2008 Issue Analog Applications Journal

Texas Instruments

Isolated CAN Reference Design (Rev. B)

Texas Instruments

This design note presents the reference design of an isolated CAN node using the isolated CAN transceiver ISO1050 and the isolated 3.3-V to 5-V DC-to-DC converter RSZ-3.305HP.

Multimode/Wireless Terminals: The Role of Semiconductor Providers

Texas Instruments

This document contains a presentation delivered by Edgar Auslander European Business Development Manager of the SC Wireless Communications Business Unit at the First European DSP Education and Research Conference on September 25 1996.DISCLAIMER: This document was part of the DSP Solution Challenge 1995 European Team Papers. It may have been written by someone whose native language is not E

Interfacing Dolphin to an External System Microcontroller (Rev. B)

Texas Instruments

This application note discusses the hardware and firmware implementation details of interfacing an external system (application) microcontroller to the Dolphin chipset. The system microcontroller performs all the application and system level tasks and is needed to set up the operation of the Dolphin chipset.

Texas Instruments has developed evaluation software that interfaces to the Dolphin chipset through hardware UART interface of the DBB03A digital baseband ASIC. However in real end applications, an external system microcontroller is needed to emulate the features of the Dolphin evaluation software. This evaluation software was purely developed for demo purposes. Any catalog low-cost microcontroller can be interfaced to the Dolphin chipset as long as they follow the Dolphin host interface protocol (SWRA043) for communication.

Texas Instruments recommends its ultra-low power MSP430 series of microcontrollers to interface with Dolphin. Specifically the firmware in this application note was developed for MSP430F1121A microcontroller.