The TI TC211 full frame charge coupled device (CCD) image sensor is used with the TCK-211 evaluation board to illustrate full frame CCD timing compatible with the EIA RS-170 standard. This document aids in the design of timing for the TI full frame CCD image sensors. The TC211 timing necessary to perform correlated double sampling (CDS) and antiblooming is included. This timing is only one method

The Texas Instruments DM646x devices support interfacing to a peripheral component interconnect (PCI) bus through its PCI port. The system or the application may contain a PCI Express® interface. In order to connect the PCI Express bus to the DM646x PCI bus an XIO2000A translation bridge is used. XIO2000A is a PCI Express to PCI/PCI-X™ bus translation bridge.

This application report provides technical background on nFBGA packages and explains how to use them to build advanced board layouts.

Understanding Portable Applications Requirements to Improve System Performance

Development can begin now for the Texas Instruments TMS320C6713 highest-performance peripheral-rich floating-point digital signal processor (DSP) systems. Because of the compatibility between TMS320C6000?DSP platform devices existing C6000?software tools and development platforms can be used to develop code for the C6713 and other future devices. This capability a

Spreeta Application Brief 005

In many applications a constant-current constant-voltage (CC/CV) dc source is needed. The I-Vcharacteristic of a constant-current constant-voltage (CC/CV) source is shown in Figure 1. This applicationreport presents an external op-amp based accurate current limit circuit suitable for CC/CV operation whenthe required constant current range is very narrow.

DN009 -- Upgrading from CC1100 to CC1101

In addition to the IALG interface that is required for an algorithm to conform to the TMS320? DSP Algorithm Standard an additional interface can be implemented to enable consumers to take advantage of the Real Time Analysis (RTA) capabilities of DSP/BIOS libraries. The Real-time Trace Control Interface (IRTC) defines an interface that when implemented allows a module?s various RTA modes to be

DRV8662, DRV2665, DRV2667 DRV8662, DRV2665, and DRV2667 Configuration Guide

This application report serves as a guide to port CC3000-compatible code to the CC3100.

This application report describes how to interface the DAC8534 digital-to-analog converter to the TMS320VC33 digital signal processing.

This application report helps current and new users of the TRF7960 high-frequency RFID/NFC reader understand the differences between the TRF7960 and the TRF7960A devices. Understanding these differences in detail and applying this knowledge to application-specific requirements helps designers make informed decisions about whether or not a bill of materials change is needed.

USB Power Switch Reverse Current Protection Application Report /PMP/LP/Power Interface/App Reports

The UCC3806 is a pin-for-pin-compatible BiCMOS replacement for the UC3846 and UC3856. However this design note explains how some functions in the UCC3806 are programmed differently. In particular the CUR LIM ADJ pin programs the maximum peak current for the current-sense amplifier. This function is completely compatible with that of previous ICs. The second function on this pin is the latch/non-

The OMAP5910 is a true system-on-a-chip device which consists of ARM925T MPU and C55X DSP cores. The device has many advanced power management modes that enable system designers to develop a very low-power multimedia communication device. This application note shows low-power design techniques and outlines the steps required to put the OMAP™ device in the lowest power consumption mode and

This application report describes methods for measuring code execution time of TMS470 and TMS570 microcontrollers. Besides the typical pin toggle approach, where the duration between two pin toggles i

DN013 -- Programming output powers on CC1101

This application report provides general guidelines for using the TI 1.8V LVDS/LVCMOS clock receiver CDCL6010 as a frequency synthesizer and/or jitter cleaner. This report reviews the basic device functionality and most efficient methods of use. The document also includes a detailed discussion of generating multiple frequencies with a common input frequency as well as a practical example of this

This application note presents several mechanisms supported by the TMS320 DSP Algorithm Standard (referred to as XDAIS) which can be employed by algorithm writers to assist application developers in optimizing their system?s performance and sharing of memory resources.The first mechanism is based on using statically allocated global data structures. The second mechanism is built on the concept