AC 8C 816 PIN PLUG

EVAL KIT, ARM CORTEX-M0+, LATCH RELAY;

Arduino Matter Discovery Bundle, Iot |Arduino AKX00081

Arduino Usb-C Cable 1M |Arduino TPX00243

Arduino TINKERKIT RELAY MODULE

WiFi/802.11 Development Tools Arduino Uno WiFi

Arduino USB Micro Cable Canon 1.8m-Orange

Arduino MICRO USB MALE TO USB A FEMALE ADAPTER

MKR WAN 1300 is a powerful board that combines the functionality of the MKR Zero and LoRa / LoRaWANTM connectivity. It is the ideal solution for makers wanting to design IoT projects with minimal previous experience in networking having a low power device. Arduino MKR WAN 1300 has been designed to offer a practical and cost effective solution for makers seeking to add Lo-Ra connectivity to their projects with minimal previous experience in networking. It is based on the Atmel SAMD21 and a Murata  CMWX1ZZABZ Lo-Ra module. The design includes the ability to power the board using two 1.5V AA or AAA batteries or external 5V. Switching from one source to the other is done automatically. A good 32 bit computational power similar to the MKR ZERO board, the usual rich set of I/O interfaces, low power Lo-Ra communication and the ease of use of the Arduino Software (IDE) for code development and programming. All these features make this board the preferred choice for the emerging IoT battery-powered projects in a compact form factor. The USB port can be used to supply power (5V) to the board. The Arduino MKR WAN 1300 is able to run with or without the batteries connected and has limited power consumption. Warning: Unlike most Arduino & Genuino boards, the MKR WAN 1300 runs at 3.3V. The maximum voltage that the I/O pins can tolerate is 3.3V. Applying voltages higher than 3.3V to any I/O pin could damage the board. While output to 5V digital devices is possible, bidirectional communication with 5V devices needs proper level shifting.

DEV BOARD 8BIT AVR RISC MCU; Silicon Manufacturer:Atmel; No. of Bits:8bit; Silicon Family Name:ATmega; Core Architecture:AVR; Core Sub-Architecture:-; Silicon Core Number:ATmega328; Kit Contents:Dev Board ATmega328 MCU; Product Range:-; SVHC:No SVHC (07-Jul-2017)

Arduino Ethernet shield 2 without POE. Technology: Development Board. Processor Type: MCU. MPN: A000024

With the MKR Vidor 4000 you can configure it the way you want; you can essentially create your own controller board. It comes loaded with hardware and potential: an 8 MB SRAM; a 2 MB QSPI Flash chip — 1 MB allocated for user applications; a Micro HDMI connector; an MIPI camera connector; and Wifi & BLE powered by U-BLOX NINA W10 Series. It also includes the classic MKR interface on which all pins are driven both by SAMD21 and FPGA. Plus, it has a Mini PCI Express connector with up to 25 user programmable pins. The FPGA contains 16K Logic Elements, 504 KB of embedded RAM, and 56 18x18 bit HW multipliers for high-speed DSP. Each pin can toggle at over 150 MHz and can be configured for functions such as UARTs, (Q)SPI, high resolution/high frequency PWM, quadrature encoder, I2C, I2S, Sigma Delta DAC, etc. The on-board FPGA can be also used for high-speed DSP operations for audio and video processing. This board also features a Microchip SAMD21. Communication between FPGA and the SAMD21 is seamless.

ARDUINO MKR THERM SHIELD;

ARDUINO MKR RGB;

ARDUINO MKR MOTOR CARRIER;

CD4081BNSR, CD40106BNSR, CD40109BNSRG4, LT3652HV, MP2322, MP1542, MC14067BDWG, TPS54620, TS13102, TCA6424A, W25Q16JVZPIQ Arduino Edge Control - ARM® Cortex®-M4F MCU 32-Bit Embedded Evaluation Board

Arduino, MKR Environmental Shield Rev2, Product Name: Arduino MKR Environmental Shield Rev2, Processor Part Number: ASX00029

ARDUINO SENSOR KIT

ARDUINO STUDENT KIT

NINA-W10 - Transceiver; 802.11 b/g/n (Wi-Fi, WiFi, WLAN) Evaluation Board