Multi-Sensor High Accuracy Digital Temperature Measurement System Features: Directly Digitize RTDs, Thermocouples, Thermistors, and Diodes Single 2.85V to 5.25V Supply Results Reported in °C or °F 20 Flexible Inputs Allow Interchanging Sensors Automatic Thermocouple Cold Junction Compensation Built-In Standard and User-Programmable Coefficients for Thermocouples, RTDs and Thermistors Configurable 2-, 3- or 4-Wire RTD Configurations Measures Negative Thermocouple Voltages Automatic Burn Out, Short-Circuit and Fault Detection Buffered Inputs Allow External Protection Simultaneous 50Hz/60Hz Rejection Includes 10ppm/°C (max) Reference (I-Grade)

2GHz to 14GHz Microwave Mixer with Integrated LO Frequency Doubler Features: Upconversion or Downconversion High IIP3: +28.2dBm at 5.8GHz +22.8dBm at 12GHz 8.0dB Conversion Loss at 5.8GHz +14.3dBm Input P1dB at 5.8GHz Integrated LO Buffer: 0dBm LO Drive Bypassable Integrated LO Frequency Doubler Low LO-RF Leakage: <–30dBm 50Ω Single-Ended RF, LO and IF Ports 3.3V/115mA Supply Fast Turn ON/OFF for TDD Operation 2mm × 3mm, 12-Lead QFN Package

Dual 12V Ideal Diode-OR and Single Hot Swap Controller with Current Monitor Features:Ideal Diode-OR and Inrush Current Control for Redundant SuppliesLow Loss Replacement for Power Schottky DiodesEnables Safe Board Insertion into a Live Backplane9V to 14V OperationCurrent Monitor OutputControls N-Channel MOSFETsLimits Peak Fault Current in ≤ 1μsAdjustable Current Limit with FoldbackAdjustable Current Limit Fault Delay0.5μs Ideal Diode Turn-On and Turn-Off TimeSmooth Switchover without OscillationFault and Power Good OutputsLTC4235-1: Latch Off After FaultLTC4235-2: Automatic Retry After Fault20-Pin 4mm x 5mm QFN Package

3GHz to 8GHz High Linearity Active Upconverting Mixer Features: 25dBm OIP3 –0.6dB Conversion Gain 14.1dB Noise Figure at 5.8GHz –154dBm/Hz Output Noise Floor Low LO-RF Leakage 0dBm LO Drive Broadband 50Ω Matched Input High Input P1dB: 10dBm at 5V 5V or 3.3V Supply at 99mA Single-Ended Output and LO Input Enable Pin –40°C to 105°C Operation (TC) 16-Lead (4mm × 4mm) QFN Package

Buffered 8-Channel, 16-Bit, 800ksps Differential 10.24V ADC with 30VP-P Common Mode Range Features: Eight Buffered Multiplexed Channels 800ksps Throughput 500pA/12nA Maximum Input Leakage at 85°C/125°C ±1LSB INL (Maximum ±10.24V Range) Guaranteed 16-Bit, No Missing Codes Differential, Wide Common Mode Range Inputs 8-Channel Multiplexer with SoftSpan Input Ranges: ±10.24V, 0V to 10.24V, ±5.12V, 0V to 5.12V ±12.5V, 0V to 12.5V, ±6.25V, 0V to 6.25V 94.2dB Single-Conversion SNR (Typical) −110dB THD (Typical) at fIN = 2kHz 128dB CMRR, –125dB Active Crosstalk (Typical) 420ns Step Response (Full-Scale, 0.005% Settling) Rail-to-Rail Input Overdrive Tolerance Programmable Sequencer with No-Latency Control Integrated Reference and Buffer (4.096V) SPI CMOS (1.8V to 5V) and LVDS Serial I/O 268mW Power Dissipation (Typical) 48-Lead (7mm × 7mm) LQFP Package

Quad, 12-Bit + Sign, 2Msps/Ch Simultaneous Sampling ADC Features:2Msps/Ch Throughput RateFour Simultaneously Sampling ChannelsGuaranteed 12-Bit, No Missing Codes8VP-P Differential Inputs with Wide InputCommon Mode Range78dB SNR (Typ) at fIN = 500kHz–88dB THD (Typ) at fIN = 500kHzGuaranteed Operation to 125°CSingle 3.3V or 5V SupplyLow Drift (20ppm/°C Max) 2.048V or 4.096VInternal Reference1.8V to 2.5V I/O VoltagesCMOS or LVDS SPI-Compatible Serial I/OPower Dissipation 40mW/Ch (Typ)Small 52-Lead (7mm × 8mm) QFN Package

40VIN, 3.5A Step-Down Silent Switcher Module Regulator Features: Complete Step-Down Switch Mode Power Supply Low Noise Silent Switcher® Architecture Wide Input Voltage Range: 3.4V to 40V Wide Output Voltage Range: 0.97V to 18V Wide Temperature Range: –40°C to 150°C (H-Grade) 3.5A Continuous Output Current, 6A peak FMEA Compliant Pinout (LTM8003-3.3) Output Stays at or Below Regulation Voltage During Adjacent Pin Short or if a Pin Is Left Floating CISPR25 Class 5 Compliant Selectable Switching Frequency: 200kHz to 3MHz External Synchronization Low Quiescent Current: 25μA (5VOUT) Tiny, Low Profile 6.25mm × 9mm × 3.32mm RoHS Compliant BGA Package

100V Overvoltage, Undervoltage and Reverse Supply Protection Controller Features:Wide Operating Voltage Range: 2.5V to 60VOvervoltage Protection to 100VReverse Supply Protection to –40VLTC4367: Blocks 50Hz and 60Hz AC PowerLTC4367: 32ms Recovery from FaultLTC4367-1: Fast 500μs Recovery from FaultNo Input Capacitor or TVS Required for Most ApplicationsAdjustable Undervoltage and Overvoltage ThresholdsControls Back-to-Back N-Channel MOSFETsLow Operating Current: 70μALow Shutdown Current: 5μA8-Pin MSOP and 3mm × 3mm DFN PackagesAEC-Q100 Qualified for Automotive Applications

60V Low IQ Buck Controller Plus 4-Channel 8A Configurable Buck DC/DCs Features: HV Buck Controller: VIN = 4.5V to 60V, VOUT = 5V/3.3V LV Buck Regulators: VINA-H = 2.25V to 5.5V, VOUT1-4 ≥ 0.8V 8×1A LV Buck Integrated Power Stages, Configurable as 2, 3 or 4 Output Channels 8 Unique Output Configurations (1A to 4A Per Channel) Low Total No-Load Input Supply Current (IQ) 15µA HV Controller Only (5VOUT) 23μA HV Controller Only (3.3VOUT) 33μA HV Controller (3.3VOUT) Plus One LV Regulator 9μA Per Additional LV Regulator Channel 1MHz to 3MHz Operation (HV Runs at 1/6 Frequency) Programmable or Synchronizable to External Clock Programmable Watchdog and Power-On Reset Delay IC Die Temperature Monitor Output Thermally Enhanced 48-Pin 7mm × 7mm QFN Package

150V VIN and VOUT Synchronous 4-Switch Buck-Boost Controller Features: 4-Switch Current Mode Single Inductor Architecture Allows VIN Above, Below or Equal to VOUT Wide VIN Range: 4.5V to 150V Wide Output Voltage Range: 1.2V ≤ VOUT ≤ 150V Synchronous Rectification: Up to 99% Efficiency ±1% 1.2V Voltage Reference Input or Output Average Current Limit On-Board LDO or External NMOS LDO for DRVCC 36V EXTVCC LDO Powers Drivers Programmable 6V to 10V DRVCC Optimizes Efficiency No Top FET Refresh Noise in Boost or Buck Mode VOUT Disconnected from VIN During Shutdown Phase-Lockable Fixed Frequency (50kHz to 600kHz) No Reverse Current During Start-Up Power Good Output Voltage Monitor 150V Rated RUN Pin with Accurate Turn-On Threshold Programmable Input Overvoltage Lockout Thermally Enhanced FE38 TSSOP Package Modified for High Voltage Operation

High Power Negative Voltage Hot Swap Controller with Energy Monitor Features: Drives Two Gates for High Power Applications Configurable Parallel, Staged Start or Single Modes Protects MOSFET with SOA Timer Programmable 15mV to 30mV Current Limit Sense Voltage with 8-Bit to 16-Bit Gear-Shift ADC with 0.7% Accuracy Monitors Voltages, Currents, Power and Energy Nonvolatile Configuration and Fault Recording Floating Topology for Rugged High Voltage Operation Selectable Inrush Control: dV/dt or Current Limit I2C/SMBus or Single-Wire Broadcast Interfaces Min/Max ADC Measurement Logging with Alerts Reboots on I2C Command with Programmable Delay Adjustable Input UV/OV Thresholds and Hysteresis 44-Pin 5mm × 8mm QFN Package

LF7GHz Wideband Low Power Active Mixer Features: Wideband Frequency Range to 7GHz Low Power: 2.7V to 3.6V, 40mA Supply Supply Current Adjustable Down to 15mA Up or Downconversion OIP3: +20dBm at 3.6GHz Out Conversion Gain: +1dB Low LO Drive: –4dBm to +2dBm LO Impedance Match Maintained During Shutdown Enable Control, 10μA Shutdown Current 2kV ESD (HBM and CDM) –40°C to 105°C Operation Small 2mm × 2mm 10-Lead QFN Package

LF7GHz Wideband Low Power Active Mixer Features: Wideband Frequency Range to 7GHz Low Power: 2.7V to 3.6V, 40mA Supply Supply Current Adjustable Down to 15mA Up or Downconversion OIP3: +20dBm at 3.6GHz Out Conversion Gain: +1dB Low LO Drive: –4dBm to +2dBm LO Impedance Match Maintained During Shutdown Enable Control, 10μA Shutdown Current 2kV ESD (HBM and CDM) –40°C to 105°C Operation Small 2mm × 2mm 10-Lead QFN Package

100kHz to 1.4GHz Differential ADC Driver/IF Amplifier Features: 100kHz to 1400MHz Bandwidth 54.4dBm OIP3 at 1MHz into a 100Ω Diff Load 48.0dBm OIP3 at 150MHz into a 100Ω Diff Load Up to 15dBm Output Power NF = 3.0dB at 240MHz Low 1/f Noise Corner User Defined Low Frequency 15.2dB Fixed Power Gain A-Grade 100% OIP3 Tested at 150MHz 0.8 nV/√Hz Total Input Noise >2.75VP-P Linear Output Swing P1dB = 22.5dBm Insensitive to VCC Variation Input/Output Internally Matched to 100Ω Differential Single 5V Supply DC Power = 850mW Unconditionally Stable

150V Low IQ, Dual, 2-Phase Synchronous Step-Down DC/DC Controller with PassThru Features: Wide VIN Range: 4.5V to 140V (150V Abs Max) Wide Output Voltage Range: 1V ≤ VOUT ≤ 60V Low Operating IQ: 16μA (48VIN to 12VOUT and 3.3VOUT) Adjustable Gate Drive Level Up to 10V Optional Spread Spectrum Operation Very Low Dropout: 100% Duty Cycle Operation Low IQ in Dropout: 78µA (One Channel On) RSENSE or Inductor DCR Current Sensing Out-of-Phase Controllers Reduce Required Input Capacitance and Power Supply Induced Noise Phase-Lockable Frequency (75kHz to 720kHz) Programmable Fixed Frequency (50kHz to 750kHz) Selectable Continuous, Pulse-Skipping, or Low Ripple Burst Mode® Operation at Light Loads Onboard LDO or External NMOS LDO for DRVCC EXTVCC LDO Powers Drivers from VOUT Programmable Input Overvoltage Lockout 48-Lead (7mm × 7mm) eLQFP Package

42V, 6A Synchronous Step-Down Silent Switcher 2 with 2.5A Quiescent Current Features: Silent Switcher ®2 Architecture Ultralow EMI Emissions on Any PCB Eliminates PCB Layout Sensitivity Internal Bypass Capacitors Reduce Radiated EMI Optional Spread Spectrum Modulation High Efficiency at High Frequency Up to 96% Efficiency at 1MHz, 12VIN to 5VOUT Up to 95% Efficiency at 2MHz, 12VIN to 5VOUT Wide Input Voltage Range: 3.4V to 42V 6A Maximum Continuous, 7A Peak Output Ultralow Quiescent Current Burst Mode® Operation 2.5μA IQ Regulating 12VIN to 3.3VOUT (LT8640S) Output Ripple < 10mVP-P External Compensation: Fast Transient Response and Current Sharing (LT8643S) Fast Minimum Switch On-Time: 30ns Low Dropout Under All Conditions: 100mV at 1A Forced Continuous Mode Adjustable and Synchronizable: 200kHz to 3MHz Output Soft-Start and Tracking Small 24-Lead 4mm × 4mm LQFN Package AEC-Q100 Qualified for Automotive Applications

16-Bit, Isolated, Sigma-Delta Modulator Features: 5 MHz to 21 MHz master clock input frequency Offset drift vs. temperature: ±0.25 μV/°C SNR: 82 dB typical 16 bits, no missing codes Full-scale analog input voltage range: ±64 mV ENOB: 13 bits typical IDD1: 10 mA maximum On-board digital isolator Operating temperature range: −40°C to +125°C High isolation common-mode transient immunity: 150 kV/μs minimum, VDD2 = 3.3 V Wide-body SOICs 16-lead SOIC_W 8-lead SOIC_IC with increased creepage Safety and regulatory approvals UL recognition 5700 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A VDE Certificate of Conformity DIN V VDE V 0884-10: VIORM = 1270 VPEAK DIN V VDE V 0884-11: VIORM = 1060 VPEAK (pending)

16-Bit, Isolated, Sigma-Delta ADC Features: 5 MHz to 21 MHz master clock input frequency Offset drift vs. temperature: ±0.6 μV/°C maximum SNR: 86 dB typical 16 bits, no missing codes Full-scale analog input voltage range: ±320 mV ENOB: 14 bits typical IDD1: 10 mA maximum On-board digital isolator Operating temperature range −40°C to +125°C (16-lead SOIC_W) −40°C to +105°C (8-lead SOIC_IC) 20 V operation on VDD1 High CMTI: 150 kV/μs minimum, VDD2 = 3.3 V Wide-body SOICs 16-lead SOIC_W 8-lead SOIC_IC with increased creepage Safety and regulatory approvals UL recognition 5700 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A (Pending) VDE Certificate of Conformity DIN V VDE V 0884-10: VIORM = 1270 VPEAK DIN V VDE V 0884-11: VIORM = 1060 VPEAK (Pending)

16-Bit, Isolated, Sigma-Delta ADC Features: 5 MHz to 21 MHz master clock input frequency Offset drift vs. temperature: ±0.6 μV/°C maximum SNR: 86 dB typical 16 bits, no missing codes Full-scale analog input voltage range: ±320 mV ENOB: 14 bits typical IDD1: 10 mA maximum On-board digital isolator Operating temperature range −40°C to +125°C (16-lead SOIC_W) −40°C to +105°C (8-lead SOIC_IC) 20 V operation on VDD1 High CMTI: 150 kV/μs minimum, VDD2 = 3.3 V Wide-body SOICs 16-lead SOIC_W 8-lead SOIC_IC with increased creepage Safety and regulatory approvals UL recognition 5700 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A (Pending) VDE Certificate of Conformity DIN V VDE V 0884-10: VIORM = 1270 VPEAK DIN V VDE V 0884-11: VIORM = 1060 VPEAK (Pending)

300 MHz, 32 32 Buffered Analog Crosspoint Switch Features: Large, 32 × 32, nonblocking switch array G = +1 (ADV3200) or G = +2 (ADV3201) operation Pin compatible 32 × 16 versions available (ADV3202/ADV3203) Single 5 V supply, dual ±2.5 V supply, or dual ±3.3 V supply (G=+2) Serial programming of switch array 2:1 OSD insertion mux per output Input sync-tip clamp High impedance output disable allows connection of multiple devices with minimal output bus load Excellent video performance  60 MHz 0.1 dB gain flatness  0.1% differential gain error (RL = 150 )  0.1° differential phase error (RL = 150 ) Excellent ac performance  Bandwidth: >300 MHz  Slew rate: >400 V/µs See data sheet for additional Features