32V, 2A Module (Power Module) Li-Ion/Polymer Battery Charger Features: Wide Input Voltage Range: 4.95V to 32V (40V Absolute Maximum) Float Voltage Options: 1-Cell: 4.1V, 4.2V 2-Cell: 8.2V, 8.4V Programmable Charge Current: Up to 2A User-Selectable Charge Termination: C/10 or Onboard Termination Timer Dynamic Charge Rate Programming/Soft-Start Pin Programmable Input Current Limit Optional Reverse Input Protection NTC Resistor Temperature Monitor 0.5% Float Voltage Accuracy Bad-Battery Detection with Auto-Reset Tiny, Low Profile (9mm × 15mm × 4.32mm) Surface Mount LGA Package

40VIN, 2A Silent Switcher Module Regulator Features: Low Noise Silent Switcher® Architecture Wide Input Voltage Range: 3.2V to 40V Wide Output Voltage Range: 0.8V to 15V 2A Continuous Output Current at 12VIN, 5VOUT, TA = 85°C 2.5A Peak Current Selectable Switching Frequency: 200kHz to 2.2MHz External Synchronization Configurable as an Inverter 6.25mm × 4mm × 2.22mm BGA Package

40VIN, 2A Silent Switcher Module Regulator Features: Low Noise Silent Switcher® Architecture Wide Input Voltage Range: 3.2V to 40V Wide Output Voltage Range: 0.8V to 15V 2A Continuous Output Current at 12VIN, 5VOUT, TA = 85°C 2.5A Peak Current Selectable Switching Frequency: 200kHz to 2.2MHz External Synchronization Configurable as an Inverter 6.25mm × 4mm × 2.22mm BGA Package

40VIN, 1.2A Silent Switcher Module Regulator Features: Low Noise Silent Switcher® Architecture CISPR 22 Class B Compliance Wide Input Voltage Range: 3.2V to 40V Wide Output Voltage Range: 0.8V to 12V 1.2A Continuous Output Current at 24VIN, 5VOUT, TA = 85°C 1.75A Peak Output Current at 3.3VOUT Selectable Switching Frequency: 200kHz to 2.2MHz External Synchronization Configurable as an Inverter 4mm × 4mm × 1.82mm BGA Package

36V, 1.5A Buck-Boost Module Regulator Features: Complete Buck-Boost Switch Mode Power Supply Wide Input Voltage Range: 3V to 36V Wide Output Voltage Range: 1V to 36V 12V/0.8A Output at 6VIN 12V/1.5A Output at 12VIN 12V/1.5A Output at 36VIN Integrated Three-Terminal Capacitors and Spread Spectrum for Excellent EMI Performance Compliant with CISPR25 Class 5 Limits (Refer to Figure 25 in the data sheet) 300kHz to 2MHz Fixed Switching Frequency with External Frequency Synchronization Adjustable Output Current Limit Output Current Monitoring RoHS Compliant Package 6.25mm × 6.25mm × 2.22mm BGA Package

14-Bit, 125Msps Dual-Channel IF/Baseband Receiver Subsystem Features: Integrated Dual 14-Bit, High-Speed ADC, Passive Filters and Fixed Gain Differential Amplifiers Up to 300MHz IF Range Lowpass and Bandpass Filter Versions Integrated Low Noise, Low Distortion Amplifiers Fixed Gain: 8dB, 14dB, 20dB or 26dB 50Ω, 200Ω or 400Ω Input Impedance Integrated Bypass Capacitance, No External Components Required 66dB SNR Up to 140MHz Input (LTM9002-AA) 76dB SFDR Up to 140MHz Input (LTM9002-AA) Auxiliary 12-Bit DACs for Gain Adjustment Clock Duty Cycle Stabilizer Single 3V to 3.3V Supply Low Power: 1.3W (665mW/ch.) Shutdown and Nap Modes 15mm × 11.25mm LGA Package

14-Bit, 125Msps Dual-Channel IF/Baseband Receiver Subsystem Features: Integrated Dual 14-Bit, High-Speed ADC, Passive Filters and Fixed Gain Differential Amplifiers Up to 300MHz IF Range Lowpass and Bandpass Filter Versions Integrated Low Noise, Low Distortion Amplifiers Fixed Gain: 8dB, 14dB, 20dB or 26dB 50Ω, 200Ω or 400Ω Input Impedance Integrated Bypass Capacitance, No External Components Required 66dB SNR Up to 140MHz Input (LTM9002-AA) 76dB SFDR Up to 140MHz Input (LTM9002-AA) Auxiliary 12-Bit DACs for Gain Adjustment Clock Duty Cycle Stabilizer Single 3V to 3.3V Supply Low Power: 1.3W (665mW/ch.) Shutdown and Nap Modes 15mm × 11.25mm LGA Package

14-Bit, 125Msps Dual-Channel IF/Baseband Receiver Subsystem Features: Integrated Dual 14-Bit, High-Speed ADC, Passive Filters and Fixed Gain Differential Amplifiers Up to 300MHz IF Range Lowpass and Bandpass Filter Versions Integrated Low Noise, Low Distortion Amplifiers Fixed Gain: 8dB, 14dB, 20dB or 26dB 50Ω, 200Ω or 400Ω Input Impedance Integrated Bypass Capacitance, No External Components Required 66dB SNR Up to 140MHz Input (LTM9002-AA) 76dB SFDR Up to 140MHz Input (LTM9002-AA) Auxiliary 12-Bit DACs for Gain Adjustment Clock Duty Cycle Stabilizer Single 3V to 3.3V Supply Low Power: 1.3W (665mW/ch.) Shutdown and Nap Modes 15mm × 11.25mm LGA Package

14-Bit Direct Conversion Receiver Subsystem Features: Integrated Dual 14-Bit, High-Speed ADC, Lowpass Filter, Differential Gain Stages and I/Q Demodulator Lowpass Filter for Each ADC Channel 1.92MHz (LTM9004-AA) 4.42MHz (LTM9004-AB) 9.42MHz (LTM9004-AC) 20MHz (LTM9004-AD) RF Input Frequency Range: 0.7GHz to 2.7GHz 50Ω Single-Ended RF and LO Ports I/Q Gain Mismatch: 0.2dB Typical I/Q Phase Mismatch: 1.5 Deg Typical Voltage-Adjustable Demodulator DC Offsets 76dB/1.92MHz SNR (LTM9004-AA) 63.5dB SFDR (LTM9004-AA) Clock Duty Cycle Stabilizer Low Power: 1.83W Shutdown and Nap Modes 15mm × 22mm LGA Package

SmartMesh WirelessHART Mote Module (22-pin PCBA) Features: Serves as a Wireless Node, or Mote, in a SmartMesh WirelessHART network with: >99.999% Network Reliability in the Most Challenging RF Environments Sub 50µA Routing Nodes Incorporates a 2.4 GHz, IEEE 802.15.4 System-on-Chip, Complete with Embedded SmartMesh Networking Software MMCX antenna connector, 39 mm × 24.4 mm PCBA module Compliant to the WirelessHART standard (IEC62591) These products contain encryption. Import/export restrictions may apply.

SmartMesh WirelessHART Mote Module with Chip Antenna Features: Serves as a Wireless Node, or Mote, in a SmartMesh WirelessHART network with: >99.999% Network Reliability in the Most Challenging RF Environments Sub 50µA Routing Nodes Incorporates a 2.4 GHz, IEEE 802.15.4 System-on-Chip, Complete with Embedded SmartMesh Networking Software On-board chip antenna, 42 mm x 24 mm PCBA module Compliant to the WirelessHART standard (IEC62591) These products contain encryption. Import/export restrictions may apply.

SmartMesh WirelessHART Mote Module with Chip Antenna Features: Serves as a Wireless Node, or Mote, in a SmartMesh WirelessHART network with: >99.999% Network Reliability in the Most Challenging RF Environments Sub 50µA Routing Nodes Incorporates a 2.4 GHz, IEEE 802.15.4 System-on-Chip, Complete with Embedded SmartMesh Networking Software On-board chip antenna, 42 mm x 24 mm PCBA module Compliant to the WirelessHART standard (IEC62591) These products contain encryption. Import/export restrictions may apply.

SmartMesh WirelessHART Embedded Manager Features: Serves as a Network Manager in a SmartMesh WirelessHART network to Enable: >99.999% Network Reliability in the Most Challenging RF Environments Sub 50µA Routing Nodes Single Board Computer with 2.4 GHz, IEEE 802.15.4 System-on-Chip, Complete with Embedded SmartMesh Networking Software 103mm x 56mm stacked PCB assembly

Ultra Precision Reference Features: 1.2µVP-P Noise 2µV/√kHr Long Term Stability Very Low Hysteresis 0.05ppm/°C Drift Temperature Stabilized 400°C/W Thermal Resistance for LTZ1000A Reduces Insulation Requirements Specied for –55°C to 125°C Temperature Range Offered in TO-99 package

Precision Operational Amplifier Features: Guaranteed 25µV max. Offset Voltage Guaranteed 0.6µV/°C max. Offset Voltage Drift with Temperature Excellent 1.0µV/Month max. Long Term Stability Guaranteed 0.6µVP-P max. Noise Guaranteed 2.0nA max. Input Bias Current

Ultraprecision Operational Amplifier Features: Ultralow offset voltage TA = 25°C, 25 μV maximum Outstanding offset voltage drift 0.3 μV/°C maximum Excellent open-loop gain and gain linearity 12 V/μV typical CMRR: 130 dB minimum PSRR: 115 dB minimum Low supply current 2.0 mA maximum Fits industry-standard precision operational amplifier sockets

Precision RRIO Dual Op Amp Features: Single-supply operation  Wide bandwidth: 4 MHz  Low offset voltage: 65 μV  Unity-gain stable  High slew rate: 4.0 V/μs  Low noise: 3.9 nV/√HzOP284-EP supports defense and aerospace applications (AQEC standard) Download OP284-EP data sheet (pdf) Military temperature range (−55°C to +125°C) Controlled manufacturing baseline 1 assembly/test site 1 fabrication site Enhanced product change notification Qualification data available on request V62/14624 DSCC Drawing Number

Low Noise, High Speed Precision Operational Amplifiers Features: Guaranteed 3.8nv/√Hz max 1kHz Noise Guaranteed 35.5nv/√Hz max 10Hz Noise Very Low Peak-to-Peak Noise, 80nV Typical Guaranteed 25µV max Offset Voltage Guaranteed 0.6µV/°C max Drift with Temperature Guaranteed 11V/µsec min Slew Rate (OP-37) Guaranteed 1 Million min Voltage Gain

Low Noise, Precision, High Speed Operational Amplifier (AVCL5) Features: Low Noise, 80 nV p-p (0.1 Hz to 10 Hz) 3 nV/vHz @ 1 kHz Low Drift, 0.2 µV/°C High Speed, 17 V/µs Slew Rate 63 MHz Gain Bandwidth Low Input Offset Voltage, 10 µV Excellent CMRR, 126 dB (Common-Voltage @ 11 V) High Open-Loop Gain, 1.8 Million Replaces 725, OP-07, SE5534 In Gains > 5 Available in Die Form

Low Noise Quad Op Amp Features: Very Low-Noise, 5 nV/√Hz @ 1 kHz Max  Excellent Input Offset Voltage, 0.4 mV Max  Low Offset Voltage Drift, 2 µV/°C Max  Very High Gain, 1000 V/mV Min  Outstanding CMR, 110 dB Min  Slew Rate, 2 V/µs Typ  Gain-Bandwidth Product, 6 MHz Typ  Industry Standard Quad Pinouts  Available in Die Form