MicroConverter® Multichannel 24-/16-Bit ADCs with Embedded 62 Kb Flash and Single-Cycle MCU

MicroConverter® Multichannel 24-/16-Bit ADCs with Embedded 62 Kb Flash and Single-Cycle MCU

MicroConverter® Multichannel 24-/16-Bit ADCs with Embedded 62 Kb Flash and Single-Cycle MCU

2.7 V to 5.5 V, 250 μA, Rail-to-Rail Output 16-Bit nanoDACTM in a SOT-23

750 MHz, 8 × 8 Analog Crosspoint Switch

Low Power, 3.6 MHz, Low Noise, Rail-to- Rail Output, Operational Amplifiers

12-Bit, 20 MSPS/40 MSPS/65 MSPS Dual A/D Converter

Dual-Channel, 5 kV Isolators with Integrated DC-to-DC Converter

5 V, ±15 kV ESD Protected Half-Duplex, RS-485/RS-422 Transceivers

Dual-Channel Digital Isolators, 5 Kv

2.7 V to 5.5 V, Serial-Input, Voltage-Output, 16-Bit nanoDAC in 10-lead LFCSP, 16-lead 3 mm x 3 mm LFCSP, and 16-lead TSSOP Features: 12-/16-bit resolution 1 LSB INL 11.8 nV/√Hz noise spectral density 1 μs settling time 1.1 nV-sec glitch energy 0.05 ppm/°C temperature drift 5 kV HBM ESD classification See data sheet for additional features Also available in16-lead TSSOP

Wideband, High Output Current, Fast Settling Op Amp

Low Cost, Low Power Video Op Amp

64-Position OTP Digital Potentiometer

Precision Micropower, OVP, RRIO Operational Amplifier

Super Sequencer and Monitor with Margining Control and Non-Volatile Fault Recording Features: Complete supervisory and sequencing solution for up to 8 supplies 16 event deep black box nonvolatile fault recording 8 supply fault detectors enable supervision of supplies to: < 0.5% accuracy at all voltages at 25°C; < 1.0% accuracy across all voltages and temperatures 4 selectable input attenuators allow supervision of supplies to: 14.4 V on VH; 6 V on VP1 to VP3 (VPx) 8 programmable driver outputs, PDO1 to PDO8 (PDOx) Sequencing engine (SE) implements state machine control of PDO outputs: conditional on input events; Power-up and power-down sequence control; Fault event handling; Interrupt on warnings; Watchdog can be integrated in SE; software control through SMBus User EEPROM: 256 bytes Complete voltage margining solution for 4 voltage rails 4 voltage output 8-bit DACs (0.300 V to 1.551 V) allow voltage adjustment via dc-to-dc converter trim/feedback node 12-bit ADC for readback of all supervised voltages Reference input (REFIN) has 2 input options: Driven directly from 2.048 V (±0.25%) REFOUT pin; More accurate external reference for improved ADC performance Device powered by the highest of VPx, VH for improved redundancy Industry-standard 2-wire bus interface (SMBus) Guaranteed PDO low with VH, VPx = 1.2 V 4 dual-function inputs, VX1 to VX4 (VXx): High impedance input to supply fault detector with thresholds between 0.573 V and 1.375 V; General-purpose logic input

Precision, Selectable Gain, Fully Differential Funnel Amplifier Features: Precision attenuation: G = 0.4, G = 0.8 Fully differential or single-ended input/output Differential output designed to drive precision ADCs Drives switched capacitor and Σ-Δ ADCs Rail-to-rail output VOCM pin adjusts output common-mode voltage Robust overvoltage protection up to ±15 V (VS = +5 V) Single supply: 3 V to 10 V Dual supplies: ±1.5 V to ±5 V High performance Suited for driving 18-bit converters up to 4 MSPS 10 nV/√Hz output noise 3 ppm/°C gain drift 500 μV maximum output offset 50 V/μs slew rate Low power: 3.2 mA supply current

Ultralow Quiescent Current, 150 mA, CMOS Linear Regulators Features: Ultralow quiescent current IQ = 560 nA with 0 μA load IQ = 860 nA with 1 μA load Stable with 1 μF ceramic input and output capacitors Maximum output current: 150 mA Input voltage range: 2.2 V to 5.5 V Low shutdown current: <50 nA typical Low dropout voltage: 195 mV @ 150 mA load Initial accuracy: ±1% Accuracy over line, load, and temperature: ±3.5% 15 fixed output voltage options: 1.2 V to 4.2 V Adjustable output available PSRR performance of 72 dB @ 100 Hz See data sheet for additional features

Ultralow Quiescent Current, 150 mA, CMOS Linear Regulators Features: Ultralow quiescent current IQ = 560 nA with 0 μA load IQ = 860 nA with 1 μA load Stable with 1 μF ceramic input and output capacitors Maximum output current: 150 mA Input voltage range: 2.2 V to 5.5 V Low shutdown current: <50 nA typical Low dropout voltage: 195 mV @ 150 mA load Initial accuracy: ±1% Accuracy over line, load, and temperature: ±3.5% 15 fixed output voltage options: 1.2 V to 4.2 V Adjustable output available PSRR performance of 72 dB @ 100 Hz See data sheet for additional features

High Voltage Latch-up Proof 8-Channel Multiplexer Features: Latch-up proof 8 kV HBM ESD rating Low on resistance (13.5 Ω) ±9 V to ±22 V dual supply operation 9 V to 40 V single supply operation 48 V supply maximum ratings Fully specified at ±15 V, ±20 V, +12V and +36V VSS to VDD analog signal range Qualified for automotive applicationsADG5408-EP supports defense and aerospace applications (AQEC standard) Download ADG5408-EP Data Sheet (pdf) Military temperature range: –55°C to +125°C Controlled manufacturing baseline One assembly/test site One fabrication site Enhanced product change notification Qualification data available on request V62/16607 DSCC Drawing Number