24.0 GHz to 29.5 GHz, 5G, Microwave Upconverter and Downconverter Features:RF input/output frequency range: 24.0 GHz to 29.5 GHz2 upconversion modesDirect conversion from differential baseband I/QSingle-ended, complex IF to RF, single-sideband upconversion2 downconversion modesDirect conversion from RF to differential baseband I/Q downconversionSingle-ended complex IF image rejection conversionLO input frequency range: 5 GHz to 15 GHzLO doubler or quadrupler for up to 30 GHzMatched, 50 impedance, single-ended RF input and outputMatched, 50 impedance single-ended LO inputTemperature compensation circuits to minimize temperature variationsProgrammable baseband I/Q common-mode voltageReceiver and transmitter gain and power control through fast settling DSALow phase variation vs. gain controlFast TDD switching time via external pinsUpconversion modeSideband rejection and carrier feedthrough optimizationEnvelope detector for LO feedthrough calibrationDownconversion modeImage rejection and I/Q imbalance optimizationBaseband I/Q dc offset correctionReceiver mixer power detector for receiver gain settingLO chain features2 and 4 modesVariable gain to accommodate various LO drive strength values>360 phase control shifter for LO synchronization, separate settings for receiver and transmitter modesProgrammable via a 3-wire SPI interface60-terminal, 9 mm 8 mm, LGA packageCommon-mode input pin to track desired common mode to ADC, 0.75 V to 2.15 V voltage range

K Band Downconverter with Integrated Fractional-N PLL and VCO Features: RF front end with integrated RF balun and LNA Double balanced, active mixer with high dynamic range IF amplifier Fractional-N synthesizer with low phase noise, multicore VCO 5 V supply operation with integrated LDO regulators Output P1dB: 7 dBm Output IP3: 16 dBm Conversion gain: 36 dB Noise figure: 7 dB RF input frequency range: 16.95 GHz to 22.05 GHz Internal LO frequency range: 16.35 GHz to 21.15 GHz IF frequency range: 900 MHz to 2500 MHz Single-ended 50 Ω input impedance and 75 Ω IF output impedance Programmable via 4-wire SPI 32-lead, 5 mm × 5 mm LFCSP

K Band Downconverter with Integrated Fractional-N PLL and VCO Features: RF front end with integrated RF balun and LNA Double balanced, active mixer with high dynamic range IF amplifier Fractional-N synthesizer with low phase noise, multicore VCO 5 V supply operation with integrated LDO regulators Output P1dB: 7 dBm Output IP3: 16 dBm Conversion gain: 36 dB Noise figure: 7 dB RF input frequency range: 16.95 GHz to 22.05 GHz Internal LO frequency range: 16.35 GHz to 21.15 GHz IF frequency range: 900 MHz to 2500 MHz Single-ended 50 Ω input impedance and 75 Ω IF output impedance Programmable via 4-wire SPI 32-lead, 5 mm × 5 mm LFCSP

Dual-mode, Ka Band Upconverter withIntegrated Fractional-N PLL and VCO Features: RF output frequency range: 27 GHz to 31 GHz Two upconversion modes Direct upconversion from differential baseband I/Q (I/Q mode) Single upper sideband upconversion (IF mode) 1 dB bandwidth: 500 MHz (I/Q mode) Input frequency range: 2 GHz to 3 GHz (IF mode) Matched, 50 Ω, single-ended RF output Matched, 50 Ω, single-ended IF input Programmable baseband I/Q common mode-voltage Sideband rejection and carrier feedthrough optimization Combined RF and IF gain dynamic range: 70 dB Programmable automatic IF gain control Programmable via 3-wire or 4-wire SPI 40-terminal, 6 mm × 6 mm, RoHS compliant LGA

Dual-mode, Ka Band Upconverter withIntegrated Fractional-N PLL and VCO Features: RF output frequency range: 27 GHz to 31 GHz Two upconversion modes Direct upconversion from differential baseband I/Q (I/Q mode) Single upper sideband upconversion (IF mode) 1 dB bandwidth: 500 MHz (I/Q mode) Input frequency range: 2 GHz to 3 GHz (IF mode) Matched, 50 Ω, single-ended RF output Matched, 50 Ω, single-ended IF input Programmable baseband I/Q common mode-voltage Sideband rejection and carrier feedthrough optimization Combined RF and IF gain dynamic range: 70 dB Programmable automatic IF gain control Programmable via 3-wire or 4-wire SPI 40-terminal, 6 mm × 6 mm, RoHS compliant LGA

K Band Quadrature Demodulator with Integrated Fractional-N PLL and VCO Features: Fractional-N synthesizer with low phase noise VCO K band quadrature demodulator Programmable via 4-wire SPI RF operating frequency range: 17 GHz to 22 GHz LO internal frequency range: 17 GHz to 21.5 GHz Double sideband noise figure: 5 dB at maximum conversion gain Output integrated phase noise, 1 kHz to 10 MHz: <1° Maximum conversion gain of >50 dB Conversion gain control range of >50 dB IM3 of −54 dBc at −30 dBm composite input level, ΔfRF = 1 MHz 3 baseband, SPI-selectable LPFs with corner frequencies of: 125 MHz, 250 MHz, and 500 MHz on each baseband path

24 GHz to 29.5 GHz Transmitter/Receiver, Single Polarization Beamformer Features:RF frequency range: 24 GHz to 29.5 GHz16 configurable transmit channels16 configurable receive channelsFast TDD switching time using external pinsMatched, 50 , single-ended RF inputs and outputsIntegrated transmitter power detectors and temperature sensorHigh resolution, 6-bit vector modulators for phase controlHigh resolution, 6-bit and 5-bit DVGAs for amplitude controlGain compensation over temperatureMemory for 256 beam positionsSingle power supply required: 3.3 V with on-chip LDO for 1.8 VAdjustable power modes for power consumption reduction3-wire or 4-wire SPI supporting up to a 61.44 MHz SPI clock speed72-lead, 10 mm 10 mm, microwave LGA package

24.0 GHz to 29.5 GHz Transmit/Receive Dual Polarization Beamformer Features: RF range: 24.0 GHz to 29.5 GHz >12.5 dBm output power at 3% EVM with a 400 MHz 64 QAM 5G NR waveform, at only 310 mW / channelFully characterized with 5G NR, WiFi 5, WiFi 6, and CPE UL waveforms No degradation in EVM at wide 5G NR channel bandwidths 16 configurable transmit and receive channels Dual polarization, 8 horizontal and 8 vertical channels Fast TDD switching time using TRX_x pins Matched to 50 Ω, single-ended RF inputs and outputs Single transmitter channel power detector and temperature sensor Integrated individual receive channel overload detection circuit High resolution, 6-bit VM for phase control High resolution, 6-bit and 5-bit DVGAs for amplitude control Memory for 2048 shared transmit and receive beam positions NVM for phase and gain calibration Dual power supplies required: 1.8 V and 1.2 V with on-chip LDO voltage regulator for 1.0 V 3-wire or 4-wire SPI that supports up to 133 MHz SPI clock speed (refer to the AN-2074 Application Note, ADMV4828 Application Note) 304-ball, 10 mm × 8.5 mm CSP_BGA

24.0 GHz to 29.5 GHz Transmit/Receive Dual Polarization Beamformer Features: RF range: 24.0 GHz to 29.5 GHz >12.5 dBm output power at 3% EVM with a 400 MHz 64 QAM 5G NR waveform, at only 310 mW / channelFully characterized with 5G NR, WiFi 5, WiFi 6, and CPE UL waveforms No degradation in EVM at wide 5G NR channel bandwidths 16 configurable transmit and receive channels Dual polarization, 8 horizontal and 8 vertical channels Fast TDD switching time using TRX_x pins Matched to 50 Ω, single-ended RF inputs and outputs Single transmitter channel power detector and temperature sensor Integrated individual receive channel overload detection circuit High resolution, 6-bit VM for phase control High resolution, 6-bit and 5-bit DVGAs for amplitude control Memory for 2048 shared transmit and receive beam positions NVM for phase and gain calibration Dual power supplies required: 1.8 V and 1.2 V with on-chip LDO voltage regulator for 1.0 V 3-wire or 4-wire SPI that supports up to 133 MHz SPI clock speed (refer to the AN-2074 Application Note, ADMV4828 Application Note) 304-ball, 10 mm × 8.5 mm CSP_BGA

E-Band Upconverter SiP, 71 GHz to 76 GHz Features:Maximum conversion gain: 35 dB typical Gain tuning range: 40 dB minimum PSAT: 26 dBm typical for a gain = 23.5 dB and 19.5 dB OIP3: 31 dBm typical for a gain = 23.5 dB and POUT = 16.5 dBm per toneOP1dB: 25 dBm typical for a gain = 23.5 dB and 19.5 dB Built-in power detector Built-in envelope detector for LO nulling Fully integrated, surface-mount, 50-terminal, 16.00 mm × 14.00 mm LGA_CAV package

E-Band Low Noise Downconverter SiP, 71 GHz to 76 GHz Features:Conversion gain: 13 dB typical Image rejection: 30 dBc typical Noise figure: 5 dB typical Input IP3: 1 dBm typical Input IP2: 28 dBm typicalInput P1dB: −8 dBm typical 6× LO leakage at RFIN: <−55 dBm typical I/Q amplitude imbalance: 0.2 dB typical I/Q phase imbalance: 5° typical Fully integrated, surface-mount, 34-terminal, 11 mm × 13 mm LGA_CAV package

E-Band Low Noise Downconverter SiP, 71 GHz to 76 GHz Features:Conversion gain: 13 dB typical Image rejection: 30 dBc typical Noise figure: 5 dB typical Input IP3: 1 dBm typical Input IP2: 28 dBm typicalInput P1dB: −8 dBm typical 6× LO leakage at RFIN: <−55 dBm typical I/Q amplitude imbalance: 0.2 dB typical I/Q phase imbalance: 5° typical Fully integrated, surface-mount, 34-terminal, 11 mm × 13 mm LGA_CAV package

71 GHz to 76 GHz, 1 Watt E-Band Power Amplifier With Power Detector Features: Gain: 24 dB typical Output power for 1 dB compression: 28 dBm typical Saturated output power: 29 dBm typical Output third-order intercept: 34 dBm typical Input return loss: 18 dB typical Output return loss: 10 dB typical DC supply: 4 V at 800 mA No external matching required Die size: 2.999 mm × 3.999 mm × 0.05 mm

6.3 GHz to 18 GHz, Tunable Band-Pass Filter Features:Amplitude settling: 200 ns typicalWideband rejection: 20 dBSingle chip implementation40-lead, 6 mm 6 mm, RoHS compliant LFCSP

15.1 GHz to 32 GHz, Tunable Band-Pass Filter Features:Amplitude settling time: 200 ns typicalWideband rejection: 30 dBSingle chip implementation40-lead, 6 mm 6 mm, RoHS compliant LFCSP

1.25 GHz to 2.60 GHz Digitally Tunable Band-Pass Filter Features: Digitally tunable, octave, band-pass tuning 3 dB bandwidth: 9% ± 2% Rejection (20 dB): 16% away from fCENTER Single chip replacement for discrete filter banks Compact 10 mm × 10 mm × 1.99 mm LGA package

1.25 GHz to 2.60 GHz Digitally Tunable Band-Pass Filter Features: Digitally tunable, octave, band-pass tuning 3 dB bandwidth: 9% ± 2% Rejection (20 dB): 16% away from fCENTER Single chip replacement for discrete filter banks Compact 10 mm × 10 mm × 1.99 mm LGA package

2 GHz to 18 GHz, Digitally Tunable, High-Pass and Low-Pass Filter Features: Digitally tunable, multioctave, high-pass and low-pass tuning Independent 3 dB frequency control for up to 4 GHz of bandwidth Optimal wideband rejection: 35 dB Single chip replacement for discrete filter banks Compact 9 mm × 9 mm, 56-terminal LGA packageENHANCED PRODUCT FEATURES Supports defense and aerospace applications (AQEC standard Military temperature range of −55°C to +105°C Controlled manufacturing baseline One assembly and test site One fabrication site Production change notification Qualification data available on request V62/21604

60 GHz Millimeterwave Short Data Link Features:Integrated omnidirectional circularly polarized antennaIntegrated high band and low band diplexer for improved multipath distortionFull duplex operationSimple AM schemeData rate: 100 MbpsUltralow latencyShort link communication distance: 1 cm to 5 cm (typical)Receiver frequency: 58.0125 GHzTransmitter frequency: 63 GHzTransmitter gain: 3 dB to +32 dBIntegrated transmitter PA power detectorReceiver gain: 10 dB to +69 dBRF, IF, and BB gain controlIntegrated receiver and transmitter frequency synthesizersIntegrated reference clockOn-chip temperature sensorsDC-coupled baseband input and output3-wire serial digital interface34.70 mm 29.89, 52-terminal printed circuit assembly (PCA)

3.3 V, 3.2 Gbps Limiting Amplifier Features: Input sensitivity: 4 mV p-p 80 ps rise/fall times CML outputs: 700 mV p-p differential Programmable LOS detector: 3.5 mV to 35 mV Rx signal strength indicator (RSSI) SFF-8472-compliant average power measurement Single-supply operation: 3.3 V Low power dissipation: 145 mW Available in space-saving 3 mm × 3 mm, 16-lead LFCSP Extended temperature range: −40°C to +95°C SFP reference design available