36-V, Low Capacitance, Low-Leakage-Current, Precision, Quad SPST Switches (Normally Closed) 16-WQFN -40 to 125

2.2MHz Wide VIN Non-synchronous Boost/SEPIC/Flyback Controller 12-WSON -40 to 150

Analog Comparators Quad Differential Comparator

RS-232 Interface IC 3-5.5V Multichannel Line Drvr/Rcvr

Operational Amplifiers - Op Amps 6.5MHz 585uA Rail-to Rail I/O CMOS Op Amp

Logic Gates Quad 2-input Positive-OR gates

Two-channel differential 2:1 & 1:2 USB3.2 mux & demux 20-VQFN -40 to 105

The ISO1042 device is a galvanically-isolated controller area network (CAN) transceiver that meets the specifications of the ISO11898-2 (2016) standard. The ISO1042 device offers ±70-V DC bus fault protection and ±30-V common-mode voltage range. The device supports up to 5-Mbps data rate in CAN FD mode allowing much faster transfer of payload compared to classic CAN. This device uses a silicon dioxide (SiO2) insulation barrier with a withstand voltage of 5000 VRMS and a working voltage of 1060 VRMS. Electromagnetic compatibility has been significantly enhanced to enable system-level ESD, EFT, surge, and emissions compliance. Used in conjunction with isolated power supplies, the device protects against high voltage, and prevents noise currents from the bus from entering the local ground. The ISO1042 device is available for both basic and reinforced isolation. The ISO1042 device supports a wide ambient temperature range of –40°C to +125°C. The device is available in the SOIC-16 (DW) package and a smaller SOIC-8 (DWV) package. Features: Meets the ISO 11898-2:2016 and ISO 11898-5:2007 Physical Layer Standards Supports Classic CAN up to 1 Mbps and FD (Flexible Data Rate) up to 5 Mbps Low Loop Delay: 152 ns Protection Features DC Bus Fault Protection Voltage: ±70 V HBM ESD Tolerance on Bus Pins: ±16 kV Driver Dominant Time Out (TXD DTO) Undervoltage Protection on VCC1 and VCC2 Common-Mode Voltage Range: ±30 V Ideal Passive, High Impedance Bus Terminals When Unpowered High CMTI: 100 kV/µs VCC1 Voltage Range: 1.71 V to 5.5 V Supports 1.8-V, 2.5-V, 3.3-V and 5.0-V logic interface to the CAN controller VCC2 Voltage Range: 4.5 V to 5.5 V Robust Electromagnetic Compatibility (EMC) System-Level ESD, EFT, and Surge Immunity Low Emissions Ambient Temperature Range: –40°C to +125°C 16-SOIC and 8-SOIC Package Options Automotive Version Available: ISO1042-Q1 Safety-Related Certifications: 7071-VPK VIOTM and 1500-VPK VIORM (Reinforced and Basic Options) per DIN V VDE V 0884-11 5000-VRMS Isolation for 1 Minute per UL 1577 IEC 60950-1, IEC 60601-1 and EN 61010-1 certifications CQC, TUV and CSA Certifications All Certifications Planned

2-Channel Industry-Standard Low-Voltage Operational Amplifier 8-TSSOP -40 to 125

36-V, Ultra-Low Noise, Wide-Bandwidth, Precision Rail-to-Rail Operational Amplifier 8-SOIC -40 to 125

Power Factor Correction - PFC Nat Inter 2Ph Trans Mode PFC Cntrlr

High Speed Operational Amplifiers Wideband Voltage Feeback

Buffers & Line Drivers Quad Bus Buff Gate With 3-State Outputs

Power Switch ICs - Power Distribution Pwr Cntrlr for Bus/ 4-Port USB Hub

Non-Isolated DC/DC Converters 16A 4.5-14V-Input Wide-Out Adj Pwr Mdl

Encoders, Decoders, Multiplexers & Demultiplexers QUAD 2Ln To 1Ln Data Selector Multiplexer

AC/DC Converters BiCMOS Low-Power Current Mode

Operational Amplifiers - Op Amps Quad Low Power Rail-to-Rail I/O

Operational Amplifiers - Op Amps Low Noise JFET Input

Encoders, Decoders, Multiplexers & Demultiplexers Dual Binary 1-of-4