Search results

The reference design and application examples shown in this document highlight the typical applications for the TPS65100 in TFT LCD displays for notebooks and monitors. The TPS65100 offers a compact and small power supply solution that provides all three voltages required by TFT LCD displays. The auxiliary linear regulator controller can be used to generate a 3.3-V logic power rail for systems pow

The application on the Texas Instruments TMS320C5407 DSP board and Stonestreet One?s (SS1) Bluetooth™ daughtercard hardware is intended to show the operation of a Bluetooth Protocol Stack and the Hands-Free and Headset Profiles within the bounds of the eXpressDSP Software Reference Framework level 3 (RF3). The application incorporates several drivers and SS1?s existing Bluetopia® core st

TPS2384 PSE Controller Interface Control

The PMP4401 is a 12Vin: ±5Vout: 1W reference design module which is implemented in an industry standard SIP pinout. It includes a constant on-time synchronous Fly-Buck controller LM25018. The solution has high efficiency and good line and load regulation with 1:500V DC isolation. The power module was designed with minimized components for cost sensitive applications. PMP4394: PMP4401: and PMP4412-PM4415 have the same pinout and can be replaced by each other without modification. The isolated bipolar outputs make the design ideal for powering noise sensitive circuits used in industrial applications.

The LM88 is a dual remote diode temperature sensor with three digital comparators and has three opendrainoutputs (O_SP0 O_SP1 and O_CRIT) that can be used as interrupts or to signal system shutdown.

The PMP3866 reference design is a dual synchronous buck that uses the TPS40140 to generate 5V@5A and 3.3V@5A. The input voltage range is 18V to 30V. This design is used in a hard drive tester application. The two power supplies operate 180 degrees out of phase with each other to reduce the input

DN010 -- Close-in Reception with CC1101

The ADAL6110-16 is a light detection and ranging (LIDAR)signal processor IC that supports simultaneous capture of up to16 channels. Each channel is integrated with a 16-bit analog todigital converter (ADC) to measure the optical return signal.The ADAL6110-16 stores the captured waveforms to staticrandom access memory (SRAM) storage. The data outputreadout and functional configuration of the LIDAR signalprocessor occurs over a 4-wire serial port interface (SPI).The LIDAR signal processor features a dc balance control toreject signal offset and corruption due to modulated interference,eliminating the need for external dc cancellation circuitry. Inaddition, the LIDAR signal processor has a built-in automaticgain control (AGC) that modifies the gain of the system toensure the signal of interest is automatically scaled to themeasurement range.The ADAL6110-16 simplifies the traditional multichannelLIDAR system implementation by integrating the transimpedanceamplifier (TIA), gain and sampling stages, as well as providingthe transmitter fire signal, all of which are managed by on-chipcontrol logic. No external components are required between thephotodiodes and the TIA interface of each channel in theLIDAR signal processor.Applications Autonomous systems collision avoidance Corridor mapping Dynamic suspension and flight control Drone altitude monitoring Industrial distance measurement Mounted safety curtain systems Parking spot monitoring Blind spot detection

The PMP9455 reference design provides a highly integrated gate driver solution for 800VA to 3kVA iPure Sine Wave Low Frequency Inverter application . With its unique features of higher peak current drive capability along with integration of two transconductance amplifier with external programmable gain and filtering : the design is a perfect fit for industrial applications . The daughter card design of SM72295 can also be used in various other four switch power topologies such as Buck Boost: Interleaved Buck etc. The Reference design has also been successfully tested on Solar MPPT charger : the details of which can also be found in TIDA-00120 design (http://www.ti.com/tool/TIDA-00120).

The AD7616 is a 16-bit, DAS that supports dual simultaneous sampling of 16 channels. The AD7616 operates from a single 5 V supply and can accommodate ?10 V, ?5 V, and ?2.5 V true bipolar input signals while sampling at throughput rates up to 1 MSPS per channel pair with 90.5 dB SNR. Higher SNR performance can be achieved with the on-chip oversampling mode (92 dB for an oversampling ratio (OSR) of 2).The input clamp protection circuitry can tolerate voltages up to ?21 V. The AD7616 has 1 M? analog input impedance, regardless of sampling frequency. The single-supply operation, on-chip filtering, and high input impedance eliminate the need for driver op amps and external bipolar supplies.The device contains analog input clamp protection, a dual, 16-bit charge redistribution SAR analog-to-digital converter (ADC), a flexible digital filter, a 2.5 V reference and reference buffer, and high speed serial and parallel interfaces.The AD7616 is serial peripheral interface (SPI)/QSPI?/DSP/ MICROWIRE compatibleApplications Power line monitoring Protective relays Multiphase motor control Instrumentation and control systems Data acquisition systems (DASs)

The TPS61040 is a highly integrated low-power boost converter capable of delivering output voltages up to 28 V. Additionally using a coupled inductor enables the TPS61040 to be used in applications where higher voltages are required - up to 75 V can be achieved.

Demonstration circuit 1428A features the dual output LT3645 step-down regulator plus linear regulator. The circuit is designed to convert a 5V to 36V (55V transients) input source to 3.3V at 500mA using the buck regulator and this output is linear regulated down to provide 2.5V at 200mA. Thus the two outputs provide 300mA (buck) and 200mA (LDO).

The CC1101-CC1190EM 869MHz reference design contains schematics and layout files for the CC1101-CC1190EM 869MHz evaluation module. The reference design demonstrates good techniques for CC1101-CC1190 decoupling and RF layout. For optimum RF performance: these parts should be copied accurately. This is a 4-layer reference design with a discrete balun and an SMA antenna connector designed for a single ended 50 ohm antenna. The RF section has been designed and characterized for operation in the 869.4 - 869.65 MHz frequency sub-band (g3): but can also be used for other frequencies in the European 863 - 870 MHz band.

The PMP7022 is 1mW (3.1V at 300uA) galvanic isolated DC/DC reference design built to supply a MSP430 metering unit. The design utilising again MSP430 open loop push-pull stage. Very efficient design with current supply (inclusive load current) as low as 800uA. Input voltage range: 3.1VDC-3.3VDC; Output current: 300uA; Output voltage: 3.1VDC