Search results

This application report helps users to understand set up and use the programming timings in the register-based touch screen controller (TSC) devices. It displays the timings functions and discusses the effect on the system interface traffic and on the system power consumption.

A ready to use design that efficiently solves the problem of improper installation by adding antiparallel communication channels and appropriate control signal to enable polarity correction for the Controller Area Network (CAN) bus.

This application report describes how to set up an open source software-based development environment for the SimpleLink CC26xx and CC13xx wireless MCUs using Eclipse as integrated development environment (IDE).

The PMP5191 reference design uses the UCC28600 green-mode controller to generate a 5V/10W regulated output. The quasi-resonant switching of the UCC28600 allows this low-cost design to achieve maximum load efficiency over 78%: while the no load losses are less than 175mW.

DC336A - Demo Board

The PowerLAN™ Master Gateway Battery Management Controller uses a file identified by the .tmap file extension to load configuration parameters. This file serves to configure the operation of the controller to the specific application. Examples of configurable parameters are number of parallel and series cells in the pack number of temperature sensors and state-of-charge indication (SOCi) dis

The popularity of companding or complementary noise reduction systems is self-evident. Nearly allmedium to high quality cassette tape decks include either Dolby&regB or Dolby C type noise reduction. Ascant few have different systems such as dbx or Hi-Com. The universal appeal of compandors to n.r.system designers is the amount of noise reduction they can offer yet one of the major reasons t

HDQ Protocol Implementation with MSP430 Application Report

TI design TIDA-00318 is suitable for low power wearable device including a Qi compliant wireless receiver (bq51003)and ultra low current 1 cell Li-ion linear charger (bq25100). It features an ultra small size (5x15mm2), capable of low charging currents down to 10mA and up to 250mAwith support of termination currents as low as 1mA. Current design is designed for 135mA charge current application.

Demonstration circuit 2071A features the LTC2373 family. The LTC2374/LTC2373/LTC2372 are low noise, high speed, 8-channel, 16/18-bit successive approximation register (SAR) ADCs. The demo manual refers to the LTC2373-18 but applies to all parts in the family, the only differences being the number of bits and the maximum sample rate. Operating from a single 5V supply, the LTC2373-18 has a highly configurable, low crosstalk, 8-channel input multiplexer, supporting fully differential, pseudo-differential unipolar and pseudo-differential bipolar analog input ranges.

This reference design supports the supply for a security tracker using the TPS40200-Q1: with the opportunity of a wide input voltage range from 8V-50V. The output can handle 4.3V up to 3A due to the non-synchronous buck controller. The reference design also allows for flexible design with a simple configuration due to the device.

The LT1339 is a high power synchronous current mode switching regulator controller. The IC drives dual N-channel MOSFETs to create a single IC solution for high power DC/DC converters in applications up to 60V.The LT1339 incorporates programmable average current limiting, allowing accurate limiting of DC load current independent of inductor ripple current. The IC also incorporates user-adjustable slope compensation for minimization of magnetics at duty cycles up to 90%.The LT1339 timing oscillator operating frequency is programmable and can be synchronized up to 150kHz. Minimum off-time operation provides main switch protection. The IC also incorporates a soft start feature that is gated by both shutdown and undervoltage lockout conditions.An output phase reversal pin allows flexibility in configuration of converter types, including inverting and negative topologies.Applications 48V Telecom Power Supplies Personal Computers and Peripherals Distributed Power Converters Industrial Control Systems Lead-Acid Battery Backup Systems Automotive and Heavy Equipment

This sub system design shows an IC based implementation of over voltage: over current: reverse current: reverse polarity and miss wire protection which is more accurate: lower power and faster compared to fuses: PTCs and diodes. Programmable Logic Controller (PLC) I/O modules connected to a field power supply benefit from protection on the 24V field input connectors as power supply faults or miss wiring might damage or cause the module to not operate correctly.

This reference design discusses the use of the TSW3085EVM with the TSW3100 pattern generator to test adjacent channel power ratio (ACPR) and error vector magnitude (EVM) measurements of LTE baseband signals. By using the TSW3100 LTE GUI: patterns are loaded into the TSW3085EVM which is comprised of the DAC3482: TRF3705: and LMK04806.

Applying the Current DAC on the TSC2000, TSC2200, TSC2300, and TSC2301 Touch Screen Controllers