Search results

This reference design demonstrate an universal 85V~277V AC input 4.2W LED lighting driver using Texas Instruments TPS92310. It confirms this solution can support 3~4 LEDs in series with high efficiency: low cost and primary side regulator without any feedback on the seconday side.

This reference design provides an isolated 14.5V/35W output from a universal 85-265VAC input. It uses the UCC28740 flyback controller to provide high efficiency and minimize light load losses. Maximum load efficiency is over 88%. The average efficiency (measured at 25%: 50%: 75%: and 100% load) is 87.9%. The UCC28740 also provides accurate current limiting which eliminates the need for a load protecting switch on the output.

The ADAU1472 is a high quality SigmaDSP? digital audio?processor with a large internal memory, enabling efficient audio?source separation, far field voice capture, speech processing, deep?learning, and advanced audio signal processing. The processor combines the highly optimized Cadence? Tensilica? HiFi? 4?audio/voice processor with custom Analog Devices, Inc.,?instruction extensions for math acceleration, and a flexible input and output architecture. The?HiFi 4 processor supports four 32-bit ? 32-bit multiplier?accumulators (MACs) per cycle with 72-bit accumulators, dual 64-bit memory load, and a native Institute of Electrical and?Electronics Engineers (IEEE) single precision, floating-point multiplier.The ADAU1472 processor offers performance up to 270.336 MHz,?supports low latency, sample by sample audio processing, and?block by block processing paradigms in parallel. The integer?phase-locked loop (PLL) and flexible clock generator hardware?can generate up to 15 audio sample rates simultaneously (8 kHz?to 192 kHz). These clock generators, along with the on-board?asynchronous sample rate converters (ASRCs) and flexible?hardware audio routing matrix, greatly simplify the design of?complex audio systems.The HiFi 4 digital signal processor (DSP) core has 480 kB of L1?memory running at the DSP core clock rate, which consists of?256 kB data random access memory (RAM), 64 kB instruction?RAM, 128 kB data cache, and 32 kB instruction cache, along with?2 MB of L2 system static random access memory (SRAM)?running at one half of the DSP core clock rate. The processor?also supports up to 2 GB of external flash memory to enable the?storage of large data tables and self boot code.Dual on-chip power domains allow low power operation,?including the capability of routing audio through a flexible audio?routing matrix with IOVDD as the only active supply.?The configurable voice detection hardware can detect human?speech onset while operating in a low power state and can?generate both internal DSP and external wake-up signals.The ADAU1472 interfaces with a wide range of analog-to-digital?converters (ADCs), digital-to-analog converters (DACs), digital?audio devices, amplifiers, and control circuitry due to its highly?configurable serial ports, Sony/Philips digital interface?format (S/PDIF) interfaces, and multipurpose input/output?pins. The device can also directly interface with up to 14 pulse?density modulated (PDM) output microphones due to?integrated decimation filters specifically designed for that?purpose. The PDM outputs with integrated interpolation filters?provide direct connectivity to PDM input Class D amplifiers.The processor has two serial peripheral interface (SPI) bus master?control ports that allow the device to communicate with multiple?SPI-compatible devices including support for single, dual, and?quad input/output operation. In addition, the SPI flash port?allows direct memory mapped read access with minimal central?processing unit (CPU) overhead and standalone self boot?operation.The combined high performance DSP core, large RAM, and?small footprint make the ADAU1472 an ideal replacement for?large, general-purpose DSPs that consume more power for the?same processing load.Applications Far field voice interface devices Audio source separation Embedded deep learning for audio Commercial and professional audio processing

This TI Precision Verified Design provides the theory: component selection: simulation: complete PCB schematic and layout: bill of materials: and measured performance of a split-supply: high-side four decade current sensing solution that can accurately detect load currents from 10uA-100mA. The corresponding linear output is from 10mV to 4.9V which enables measurement by common 5V ADCs. The design utilizes the PGA281: an instrumentation amplifier with pin-programmable gain and a wide common-mode voltage range: to provide a more accurate and versatile solution than traditional op amps.See more TI Precision Designs

This reference design is a solution for a Li-Ion charge management IC. It has a highly integrated battery charge IC utilizing synchronous switch mode power conversion for efficient and comprehensive charge control of a single cell Li-Ion battery. The solutionprovides a convenient method to evaluate the operation and performance of the IC.

The LTM4647 is a complete 30A output switching mode step-down DC/DC ?Module? (power module) regulator. Included in the package are the switching controller, power FETs, inductor and all supporting components. Operating over an input voltage range of 4.7V to 15V, the LTM4647 supports an output voltage range of 0.6V to 1.8V, set by a single external resistor. Only a few input and output capacitors are needed.Its high efficiency design delivers 87% efficiency from 12V input to 1.0V output with 30A continuous load current. High switching frequency and a current-mode architecture enable a very fast transient response to line and load changes without sacrificing stability. The device supports frequency synchronization, programmable multiphase operation, N+1 phase redundancy, and output voltage tracking for supply rail sequencing.Fault protection features include overvoltage and overcurrent protection. The power module is offered in a space saving 9mm ? 15mm ? 5.01mm BGA package. The LTM4647 is available with SnPb (BGA) or RoHS compliant terminal finish.Applications Telecom, Networking and Industrial Equipment Point of Load Regulation

This TI Reference Design demonstrates a single op amp used as a slew rate limiter. In control systems for valves or motors: abrupt changes in voltages or currents can cause mechanical damages. By controlling the slew rate of the command voltages: into the drive circuits: the load voltages can ramp up and down at a safe rate.

Design features low component count and low cost isolated flyback: converting the universal mains (85Vac…275Vac) to 5.2V@200mA. Due to primary side regulation of the controller UCC28700: no optocoupler is needed to close the loop.