Search results

DC352A Demo Board for: LTC1629 PolyPhase, High Efficiency, Synchronous Step-Down Switching Regulator LTC1628-SYNC High Efficiency, 2-Phase Synchronous Step-Down Switching Regulator

The LTC6905-X series of parts are precision, fixed frequency, silicon oscillators designed to minimize board space while maximizing accuracy and ease of use.Programmed at the factory to a fixed frequency, the LTC6905-X series of parts need no external trim components. An internal three-state divider allows for division of the master clock by 1, 2 or 4, providing 3 frequencies (for each device).The LTC6905-X series operate with a single 2.7V to 5.5V power supply and provide a rail-to-rail, 50% duty cycle, square wave output. The OE pin will disable the output when brought low and synchronously enable the output when brought high, avoiding pulse slivers.The four products of the LTC6905-X family are: LTC6905-133: fOSC = 133MHz, 66.7MHz, 33.3MHz LTC6905-100: fOSC = 100MHz, 50MHz, 25MHz LTC6905-96: fOSC = 96MHz, 48MHz, 24MHz LTC6905-80: fOSC = 80MHz, 40MHz, 20MHz?The LTC6905-X series of parts are designed with a factory trim option to modify the divider ratios from 1, 2, 4 to 8, 16, 32. A second trim option allows for additional master clock frequencies. For the alternate divider ratios and unlisted frequencies, contact LTC marketing.Protected by U.S. Patents, including 6614313, 6342817.Applications Data Clocks for High Reliability Applications High Vibration, High Acceleration Environments Replacement for Fixed Crystal and Ceramic Oscillators

Demonstration circuit DC1095 is a micropower synchronous buck-boost converter based on the LTC3538 monolithic buck-boost regulator. The DC1095 has an input voltage range of 2.4V to 5.5V and an output of 3.3V @ 800mA.

Demonstration circuit 1045 is a Telecom isolated DC/DC converter featuring the LTC3805 constant frequency current mode flyback controller. The DC1045 converts 36V to 72V input voltage to an isolated 3A of output current at 3.3V. The 200kHz constant frequency operation is maintained down to very light load to reduce low frequency noise generated over a wide range of load current.

The LTM4651 is an ultralow noise, 58V, 24W DC/DC ?Module? inverting topology regulator. It regulates a negative output voltage (VOUT?) from a positive input supply voltage (VIN), and is designed to meet the radiated emissions requirements of EN55022. Conducted emission requirements can be met by adding standard filter components.Included in the package are the switching controller, power MOSFETs, inductor, filters and support components. The LTM4651 can regulate VOUT? to a value between ?0.5V and ?26.5V, provided that its input and output voltages adhere to the safe operating area criteria of the LTM4651: VIN + |VOUT?| ? 58V. A switching frequency range of 250kHz to 3MHz is supported (400kHz default) and the module can synchronize to an external clock.Despite being an inverting topology regulator, no level shift circuitry is needed to interface to the LTM4651?s RUN, PGOOD or CLKIN pins; those pins are referenced to GND.The LTM4651 is offered in a 15mm ? 9mm ? 5.01mm BGA package with SnPb or RoHS compliant terminal finish.Applications Avionics, Industrial Control and Test Equipment Video, Imaging and Instrumentation 48V Telecom and Network Power Supplies RF Systems

DC373A-A: Demo Board for the LT1725 General Purpose Isolated Flyback Controller.

DC1983A: Demo Board for the LTC5510 1MHz to 6GHz Wideband High Linearity Active Mixer.

Demonstration circuit 2707B uses the LTC®4418 to arbitrate between two input supply rails, selecting the highest priority, valid supply to power the load. The V1 rail is defined to have higher priority and the V2 rail has lower priority. Both rails have individual overvoltage and undervoltage comparators for setting valid window thresholds with external resistive dividers. If the highest priority rail voltage V1 falls out of the defined window (overvoltage or undervoltage), the V2 rail, if it is valid, is enabled and powers the load. Two or more LTC4418s can be cascaded to provide switchover between more than two rails.

The ADP1878?/ ADP1879 are versatile current mode, synchronous step-down controllers. They provide superior transient response, optimal stability, and current-limit protection by using a constant on-time, pseudo fixed frequency with a programmable current limit, current control scheme. In addition, these devices offer optimum performance at low duty cycles by using a valley, current mode control architecture. This allows the ADP1878 / ADP1879 to drive all N-channel power stages to regulate output voltages to as low as 0.6 V.The ADP1879 is the power saving mode (PSM) version of thedevice and is capable of pulse skipping to maintain outputregulation while achieving improved system efficiency at lightloads (see the ADP1879 Power Saving Mode (PSM) section formore information).Available in three frequency options (300 kHz, 600 kHz, and1.0 MHz, plus the PSM option), the ADP1878 / ADP1879 are wellsuited for a wide range of applications that require a single-inputpower supply range from 2.95 V to 20 V. Low voltage biasing issupplied via a 5 V internal low dropout regulator (LDO).In addition, soft start, programmability is included to limitinput in-rush current from the input supply during startup andto provide reverse current protection during precharged outputconditions. The low-side current sense, current gain scheme andintegration of a boost diode, along with the PSM/forced pulsewidthmodulation (PWM) option, reduce the external part countand improve efficiency.The ADP1878/ADP1879 operate over the ?40?C to +125?Cjunction temperature range and are available in a 14-LeadLFCSP_WD package.APPLICATIONS Telecom and networking systems Mid to high-end servers Set-top boxes DSP core power supplies

The LTC7812 is a high performance synchronous Boost+Buck DC/DC switching regulator controller that drives all N-channel power MOSFET stages. It contains independent step-up (boost) and step-down (buck) controllers that can regulate two separate outputs or be cascaded to regulate an output voltage from an input voltage that can be above, below or equal to the output voltage. The LTC7812 operates from a wide 4.5V to 38V input supply range. When biased from the output of the boost regulator, the LTC7812 can operate from an input supply as low as 2.5V after start-up. The 33?A no-load quiescent current extends operating run time in battery-powered systems.Unlike conventional buck-boost regulators, the LTC7812?s cascaded Boost+Buck solution has continuous, nonpulsating, input and output currents, substantially reducing voltage ripple and EMI. The LTC7812 has independent feedback and compensation points for the boost and buck regulation loops, enabling a fast output transient response that can be easily optimized externally.Applications Automotive and Industrial Power Systems High Power Battery Operated Systems

DC800A-B: Demo Board for the LT1993-4 900MHz Low Distortion, Low Noise Differential Amplifier/ADC Driver (AV = 4V/V).

The HMC773ALC3B is a general-purpose, double balanced mixer ina leadless, RoHS compliant LCC package that can be used as anupconverter or downconverter from 6 GHz to 26 GHz. Thismixer requires no external components or matching circuitry. The HMC773ALC3B provides excellent LO to RF and LO to IFsuppression due to optimized balun structures. The mixeroperates well with LO drive levels of 13 dBm or above. TheHMC773ALC3B eliminates the need for wire bonding, allowing useof surface-mount manufacturing techniques.Applications Point to point radios Point to multipoint radios and very small aperture terminals (VSATs) Test equipment and sensors Military end use

The LTM2887 is a complete galvanic digital ?Module? (micromodule) isolator. No external components are required. A single 3.3V or 5V supply powers both sides of the interface through an integrated, isolated DC/DC converter. A logic supply pin allows easy interfacing with different logic levels from 1.62V to 5.5V, independent of the main supply.Available options are compliant with SPI and I2C (master mode only) specifications.The isolated side includes two 5V nominal power supplies, including programmable current limit, each capable of providing more than 100mA of load current. The supplies may be adjusted from their nominal value using a single external resistor.Coupled inductors and an isolation power transformer provide 2500VRMS of isolation between the input and output logic interface. This device is ideal for systems where the ground loop is broken, allowing for a large common mode voltage range. Communication is uninterrupted for common mode transients greater than 30kV/?s.Applications Isolated SPI or I2C Interfaces Industrial Systems Test and Measurement Equipment Breaking Ground Loops

The AD9670 is designed for low cost, low power, small size, andease of use for medical ultrasound applications. It contains eightchannels of a VGA with an LNA, a CW harmonic rejection I/Qdemodulator with programmable phase rotation, an antialiasingfilter, an ADC, and a digital demodulator and decimator for dataprocessing and bandwidth reduction.Each channel features a maximum gain of up to 52 dB, a fullydifferential signal path, and an active input preamplifier termination.The channel is optimized for high dynamic performance andlow power in applications where a small package size is critical.The LNA has a single-ended-to-differential gain that is selectablethrough the serial port interface (SPI). Assuming a 15 MHz noisebandwidth (NBW) and a 21.6 dB LNA gain, the LNA input SNRis 94 dB. In CW Doppler mode, each LNA output drives an I/Qdemodulator that has independently programmable phaserotation with 16 phase settings.Power-down of individual channels is supported to increasebattery life for portable applications. Standby mode allows quickpower-up for power cycling. In CW Doppler operation, theVGA, antialiasing filter, and ADC are powered down. The ADCcontains several features designed to maximize flexibility andminimize system cost, such as a programmable clock, dataalignment, and programmable digital test pattern generation.The digital test patterns include built-in fixed patterns, built-inpseudorandom patterns, and custom user-defined test patternsentered via the SPI.Applications Medical imaging/ultrasound Nondestructive testing (NDT)

The LTM8051 is quad 40VIN, 1.2A step-down Silent Switcher ?Module? regulator. The Silent Switcher architecture minimizes EMI while delivering high efficiency at frequencies up to 3MHz. Included in the package are the controllers, power switches, inductors, and support components. Operating over a wide input voltage range, the LTM8051 supports output voltages from 0.8V to 8V, and a switching frequency range of 300kHz to 3MHz, each set by a single resistor. Only the bulk input and output filter capacitors are needed to finish the design. The LTM8051 product video?is available on website. The LTM8051 is packaged in a compact (6.25mm ? 11.25mm ? 2.22mm) over-molded Ball Grid Array (BGA) package suitable for automated assembly by standard surface mount equipment. The LTM8051 is available with SnPb (BGA) or RoHS compliant.APPLICATIONS Automated Test Equipment Distributed Supply Regulation Industrial Supplies Medical Equipment

The LTC2378-20, LTC2377-20 and LTC2376-20 are 20‑bit, low power, low noise SAR ADCs with serial outputs that operate from a single 2.5V supply. The demo manual refers to the LTC2378-20 but applies to all parts in the family, the only difference being the maximum sample rate. The LTC2378-20 supports a ±5V fully differential input range with a 104dB SNR, consumes only 21mW and achieves ±2ppm INL max with no missing codes at 20 bits. The DC1925A demonstrates the DC and AC performance of the LTC2378-20 in conjunction with the DC590 QuikEval™ and DC890 PScope™ data collection boards. Use the DC590 to demonstrate DC performance such as peak-to-peak noise and DC linearity.

The ADP5080 is a fully integrated, high efficiency power solution for multicell lithium ion battery applications. The device can connect directly to the battery, which eliminates the need for preregulators and, therefore, increases the battery life of the system.The ADP5080 integrates two keep-alive LDO regulators, five synchronous buck regulators, a configurable four-switch buck boost regulator, and a high voltage LDO regulator. The ADP5080 is a highly integrated power solution that incorporates all power MOSFETs, feedback loop compensation, voltage setting resistor dividers, and discharge switches, as well as a charge pump to generate a global bootstrap voltage.All these features help to minimize the number of external components and PCB space required, providing significant advantages for portable applications. The switching frequency is selectable on each channel from 750 kHz to 2 MHz.Key functions for power applications, such as soft start, selectable preset output voltage, and flexible power-up and power-down sequences, are provided on chip and are programmable via the I2C interface with fused factory defaults. The ADP5080 is available in a 72-ball WLCSP 0.5 mm pitch package.APPLICATIONS DSLR cameras Non-reflex (mirrorless) cameras Portable instrumentation

The ADAR1000 is a 4-channel, X and Ku frequency band, beamforming core chip for phased arrays. This device operates in half-duplex between receive and transmit modes. In receive mode, input signals pass through four receive channels and are combined and output at the common RF_IO pin. In transmit mode, the RF_IO input signal is split and passes through the four transmit channels. In both modes, the ADAR1000 provides a ?31 dB gain adjustment range and a full 360? phase adjustment range in each radio frequency (RF) channel, with 6-bit resolution (less than ?0.5 dB and 2.8?, respectively).A simple 4-wire serial port interface (SPI) controls all of the on-chip registers. In addition, two address pins allow SPI control of up to four devices on the same serial lines. Dedicated transmit and receive load pins also provide synchronization of all ADAR1000 chips in the same array, and a single pin controls fast switching between the transmit and receive modes. The ADAR1000 is fabricated in a silicon-germanium, bipolar CMOS (BiCMOS) process. The device is available in a compact, 88-terminal, 7 mm ? 7 mm, LGA package and is specified from ?40?C to +85?C.APPLICATIONS Phased array radar Satellite communications systems

The LT3430/LT3430-1 are monolithic buck switching regulators that accept input voltages up to 60V. A high efficiency 3A, 0.1? switch is included on the die along with all the necessary oscillator, control and logic circuitry. A current mode architecture provides fast transient response and excellent loop stability.Special design techniques and a new high voltage process achieve high efficiency over a wide input range. Efficiency is maintained over a wide output current range by using the output to bias the circuitry and by utilizing a supply boost capacitor to saturate the power switch. Patented circuitry* maintains peak switch current over the full duty cycle range. A shutdown pin reduces supply current to 30?A and a SYNC pin can be externally synchronized with a logic level input from 228kHz to 700kHz for the LT3430 or from 125kHz to 250kHz for the LT3430-1.The LT3430/LT3430-1 are available in a thermally enhanced 16-pin TSSOP package.Applications Industrial and Automotive Power Supplies Portable Computers Battery Chargers Distributed Power Systems

Demonstration Circuit DC688 is a quad output power supply intended for use in small to medium size TFT panels. The circuit features the LT1942 quad output switching regulator and generates an LED driver along with the triple output supply required for the TFT panels. With an input voltage range of 3V to 4.2V, two step-up regulators and one inverting regulator provide AVDD , VON and VOFF bias voltages for the LCD panels. Another high power boost is used to drive 12 LEDs (2 strings of 6 LEDs each). For 3V minimum input voltage, up to 20mA current is available for each LED string. A built-in LED ballast circuit is included to precisely match the LED currents in the two strings.